stop start FORD RANGER 1997 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: RANGER, Model: FORD RANGER 1997 2.GPages: 361, PDF Size: 3.39 MB
Page 23 of 361
20
%*
[IS08400(R)04/96]
Engine Oil Pressure Gauge
*
[IS08500(R)01/96]
This gauge indicates the engine's oil pressure, not the oil level.
However, if your engine's oil level is low, it could affect the oil
pressure. With the engine running, the pointer should move into
the NORMAL band. If the pointer drops below the NORMAL
band while the engine is running, you have lost oil pressure
and continued operation will cause severe engine damage.
*
[IS08600(R)05/96]
If you lose engine oil pressure:
*
[IS08700(R)04/96]1.
Pull off the road as soon as safely possible.
*
[IS08800(R)03/96]2.
Turn off the engine. If you do not stop the engine as soon as
safely possible, severe engine damage could result.
*
[IS08900(R)01/96]3.
Check the engine's oil level, following the instructions on
checking and adding engine oil. Refer toEngine oilin the
Index. If you do not follow these instructions, you or others
could be injured. To assure an accurate reading, your vehicle
should be on level ground.
*
[IS09000(R)01/96]4.
If the level is low, add only as much oil as necessary before
you start the engine again. Do not overfill. Do not operate
the engine if the pointer is below the NORMAL band,
regardless of the oil level. Contact your nearest dealer for
further service actions.
[IS09100(R)01/96]
7-1/2 pica art:0020056-E
Engine oil pressure gauge Ð mechanical cluster
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997
Page 55 of 361
52
[AS30390(R)05/96]
Using the Controls of Your Compact Disc Radio
(If equipped)
[AS30400(R)05/96]
Your Ford Compact Disc Radio is capable of playing 12 cm or 8
cm discs. The player operates when the power is on and a disc
is inserted (label side up). Handle the disc by the edge only. Be
sure to read and follow all of the care and cleaning instructions
underHow to Take Care of and Clean Your CD Player and Discs.
[AS30410(R)05/96]
The digital display on your CD player will either show the
track (selection) number or the elapsed time. Select the display
mode by pressing the ºCLKª button. Indicators for play (
a),
stop (
X), and compression (C) are also on the display. These
features are described later.
[AS30420(R)05/96]
Once a disc is inserted, operation of the CD player will override
the radio.
[AS30430(R)05/96]
NOTE: The volume, bass, treble, balance, and fader controls
on the radio are also used with the CD player. Refer
to the earlier operating instructions about these
controls.
[AS30440(R)05/96]
Inserting a disc and beginning play
[AS30450(R)05/96]
Insert a disc, label side up, into the disc opening. When
inserted, the disc automatically loads into the unit and play
starts at the beginning of the first track (selection).
[AS30460(R)05/96]
NOTE: Once a disc is inserted, the disc opening is secured to
prevent the accidental insertion of another disc.
[AS30470(R)05/96]
NOTE: The CD player has heat protection circuitry to protect
the laser diode. If the temperature of the player
reaches167ÊF (75ÊC), theheat detection circuit will
shut off the player and ºCD HOTª will scroll in the
display for approximately five seconds (radio will
resume playing). When the temperature returns to
normal operating range, the CD player will again be
operational.
File:04unasr.ex
Update:Thu Mar 20 08:49:21 1997
Page 56 of 361
Electronic Sound Systems
53
[AS30480(R)05/96]
How to stop and restart the CD player
[AS30490(R)05/96]
When a disc is loaded, the unit automatically enters the play
mode. To stop temporarily, press the ºAM/FMª button. The
stop indicator (
X) in the display illuminates and operation
returns to the radio mode. To resume CD play, press the ºCDª
button.
[AS30500(R)05/96]
NOTE: If the ignition key is turned to OFF during play and
then is turned to the ON or ACCESSORY position,
the CD player will resume playing in the mode it was
in when the ignition was turned off.
[AS30510(R)05/96]
Using the ºSEEKª feature
*
[AS30520(R)05/96]
The ºSEEKª feature allows you to quickly find a particular
selection on the disc.
[AS30530(R)05/96]
Press (
b) once to repeat the current playing selection. Press
(
a) to advance to the next selection. If the (
a) button is
pressed during the last selection on the CD, the CD will
advance to the first track on the disc.
[AS30540(R)05/96]
Pressing and holding the (
b)or(
a) button will scroll
backward and forward respectively through the tracks.
[AS30550(R)05/96]
Using the ºSCANª function
[AS30560(R)05/96]
The ºSCANª function allows you to briefly sample all tracks on
a disc.
[AS30570(R)05/96]
Press the ºSCNª button to enter the scan mode. The scan mode
causes the CD to advance to the next track, play for 8 seconds,
and then advance to the next track. This continues until the
ºSCNª button is pressed a second time, the ºCDª button is
pressed, or a different tuning function is selected.
File:04unasr.ex
Update:Thu Mar 20 08:49:21 1997
Page 149 of 361
148
%*
[TO06200(R)01/96]
Starting Your Engine
*
[TO06300(R)01/96]
To start your engine:
*
[TO06400(R)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO06425(R)01/96]2.
Turn the ignition key to the ON position.
*
[TO06451(R)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO06475(R)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO06501(R)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO06510(R)01/96]
For a cold engine:
*
[TO06515(R)01/96]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO06520(R)01/96]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
%*
[TO06521(R)01/96]
For a warm engine:
*
[TO06522(R)01/96]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[TO06575(R)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997
Page 154 of 361
Starting
153
*
[TO10400(R)01/96]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[TO10650(R)01/96]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[TO10700(R)01/96]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
*
[TO13076(R)03/96]
Removing the Key From the Ignition
*
[TO13100(R)03/96]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[TO13117(R)01/96]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[TO13300(R)03/96]
If your vehicle's gearshift lever is mounted on the
column:
*
[TO13400(R)03/96]1.
Put the gearshift in P (Park).
*
[TO13500(R)03/96]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[TO13600(R)03/96]3.
Turn the ignition key to LOCK.
*
[TO13700(R)03/96]4.
Remove the key.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997
Page 187 of 361
186
%*
[GF20600(R)01/96]
Additional Special Driving Instructions for
4-Wheel Drive Vehicle Operators
*
[GF20701(R)01/96]
Driving on Hill or Slope Terrain
[GF20800(R)03/96]
When driving on a hill, avoid driving crosswise or turning on
steep slopes; you could lose traction and slip sideways. Drive
straight up, straight down or avoid the hill completely. Know
the conditions on the other side of a hill before driving over the
crest.
*
[GF20900(R)01/96]
When climbing a steep hill, start in a lower gear, rather than
finding it necessary to downshift from a higher gear after the
ascent has started. This reduces strain on the engine and the
possibility of stalling.
*
[GF21000(R)01/96]
When descending a steep hill avoid sudden braking. Rapid
pumping of the brake pedal will help slow the vehicle and still
maintain steering control.
*
[GF21101(R)01/96]
Driving on Snow or Ice
[GF21200(R)01/96]
A four-wheel drive or all-wheel drive vehicle has advantages
over two-wheel drive vehicles in snow and ice but can skid like
any other vehicle. If so equipped, keep the vehicle in four-wheel
drive if icy or slippery conditions exist.
*
[GF21300(R)01/96]
Avoid sudden applications of power and quick changes of
direction on snow or ice. Apply the accelerator slowly and
steadily when starting from a full stop.
*
[GF21310(R)01/96]
All utility-type and Four-Wheel Drive vehicles have special
design and equipment features to make them capable of
performing in a wide variety of off-road applications. Specific
design characteristics give them higher centers of gravity than
ordinary passenger cars.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 215 of 361
214
*
[GF38800(R)03/96]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift the
automatic transmission gearshift into the 2 (Second) or 1 (Low)
position.
[GF38925(R)05/96]
Servicing Your Vehicle If You Tow
*
[GF38950(R)05/96]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedulebooklet for additional information.
[GF39000(R)01/96]
Trailer towing tips
*
[GF39100(R)01/96]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[GF39200(R)01/96]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[GF39300(R)01/96]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[GF39400(R)01/96]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[GF39500(R)01/96]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
*
[GF39600(R)01/96]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 219 of 361
218
*
[ER00300(R)01/96]
The Fuel Pump Shut-off Switch
*
[ER00400(R)05/96]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[ER00500(R)05/96]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
%*
[ER00700(R)01/96]
Fuses
[ER00800(R)01/96]
Fuses protect your vehicle's electrical system from overloading.
If electrical parts in your vehicle are not working, the system
may have been overloaded and blown a fuse. Before you
replace or repair any electrical parts, check the appropriate
fuses.
[ER00900(R)01/96]
The following charts tell you which fuses protect each electrical
part of your vehicle. If a fuse blows, all the parts of your
vehicle that use that circuit will not work.
*
[ER01000(R)01/96]
Once you have determined which fuses to check, follow the
procedures underChecking and replacing fuseslater in this
chapter.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997
Page 293 of 361
Maintenance and Care
293
*
[MC32770(R)01/96]
Fuels can also be harmful if absorbed through the skin. When
refueling, be careful not to splash fuel on yourself or your
clothing. If fuel is splashed on the skin, promptly remove
contaminated clothing and wash the skin thoroughly with soap
and water.
*
[MC32772(R)01/96]
Fuels can cause severe eye irritation and possibly eye damage. If
fuel is splashed in the eyes, remove contact lenses (if worn),
flush with large amounts of water for 15 minutes, and seek
medical attention.
*
[MC32774(R)01/96]
If you are taking the medication ªAntabuseº or other forms of
disulfiram for the treatment of alcoholism, vapor or skin contact
with a gasoline-methanol blend may cause the same kind of
adverse reaction as drinking an alcoholic beverage. In sensitive
individuals, serious personal injury or sickness could result.
Consult a physician promptly if you experience an adverse
reaction.
%*
[MC32800(R)01/96]
Running Out of Fuel
*
[MC32810(R)01/96]
If your vehicle runs out of fuel, try to stop on level ground
away from traffic. Add at least two gallons (8 liters) of fuel to
start your vehicle again. If your vehicle is not on level ground,
you may need as much as five gallons (20 liters) of fuel to start
it.
*
[MC32812(R)01/96]
You may need to crank the engine several times before the fuel
system starts to pump fuel from the tank to the engine.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 297 of 361
Maintenance and Care
297
%*
[MC42450(R)01/96]
Information about your vehicle's emission control system is on
the Vehicle Emission Control Information decal located on or
near the engine. This decal identifies engine displacement and
gives some tune-up specifications.
%*
[MC42460(R)03/96]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
*
[MC42470(R)04/96]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If your check engine light is on, reference the
check engine light description under theWarning Lights and
Gaugessection. Your vehicle may not pass an I/M test with the
check engine light on. If the vehicle's powertrain system or its
battery has just been serviced, the OBD II system is reset to a
not ready for I/M testing condition. To prepare for I/M testing,
additional city and highway driving is necessary to complete the
check of the OBD II system.
*
[MC43000(R)05/96]
The driving modes required to reach the ready condition consist
of a minimum of 30 minutes of city and highway driving as
described below:
[MC43100(R)03/96]
n
20 minutes of driving in stop and go city-type traffic with at
least four (4) idle periods.
*
[MC43200(R)03/96]
n
10 minutes of driving on an expressway or highway
[MC43300(R)03/96]
Before completing the above driving modes, the engine must be
warmed up and operating temperature. Once started, the vehicle
must not be turned off during the above driving modes. If the
vehicle owner is unable to meet the I/M requirements by using
these driving patterns, an authorized service center can perform
a detailed OBD II Drive Cycle as it would any other type of
repair work.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997