brake FORD SIERRA 1982 1.G Cooling And Air Conditioning Systems Workshop Manual

passing over the evaporator fins on its way to
the vehicle interior. The refrigerant becomes a
gas again and the cycle is repeated.
Various subsidiary controls and sensors
protect the system against excessive
temperature and pressures. Additionally,
engine idle speed is increased when the
system is in use to compensate for the
additional load imposed by the compressor.
Precautions
Air conditioning refrigerant
Although the refrigerant is not itself toxic, in
the presence of a naked flame (or a lighted
cigarette) it forms a highly toxic gas. Liquid
refrigerant spilled on the skin will cause
frostbite. If refrigerant enters the eyes, rinse
them with a dilute solution of boric acid and
seek medical advice immediately.
In view of the above points, and of the need
for specialised equipment for evacuating and
recharging the system, any work which
requires the disconnection of a refrigerant line
must be left to a specialist.
Do not allow refrigerant lines to be exposed
to temperatures above 230°F (110°C) - eg
during welding or paint drying operations and
do not operate the air conditioning system if it
is known to be short of refrigerant, or further
damage may result.
Antifreeze mixture
Antifreeze mixture is poisonous. Keep it out
of reach of children and pets. Wash splashes
off skin and clothing with plenty of water.
Wash splashes off vehicle paintwork to avoid
discolouration.
Antifreeze/water mixture must be renewed
at the specified intervals to preserve its anti-
corrosive properties. In climates where
antifreeze protection is unnecessary, a
corrosion inhibitor may be used instead -
consult a Ford dealer. Never run the engine
for long periods with plain water as coolant.
Only use the specified antifreeze as inferior
brands may not contain the necessary
corrosion inhibitors, or may break down at
high temperatures. Antifreeze containing
methanol is particularly to be avoided, as the
methanol evaporates.
The specified mixture is 45 to 50%
antifreeze and 50 to 55% clean soft water (by
volume). Mix the required quantity in a clean
container.
Refer to Chapter 1, Section 46.
Refer to Chapter 1, Section 46.
Refer to Chapter 1, Section 46.
Removal
1Disconnect the battery negative lead.
2Drain the cooling system.
3If not already done, disconnect the bottom
hose from the radiator.
4Disconnect the top hose and the expansion
tank hose from the radiator.
5On automatic transmission models, place a
suitable container beneath the fluid cooler
pipe connections at the radiator. Unscrew the
union and plug the upper pipe, then repeat
the procedure on the lower pipe.
6Apply the handbrake, jack up the front of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).
7To improve access, remove the cooling fan
shroud as follows, according to model.
8On SOHC models, remove the four
retaining clips and unscrew the two retaining
screws, then withdraw the upper section of
the fan shroud. Unclip and remove the lower
section of the shroud.
9On CVH and DOHC models, unclip the
wiring connector from the fan motor(s) then
unscrew the retaining nuts and washers, and
withdraw the fan shroud(s) and cooling fan
assembly(s) (see illustration).
10On early models, unscrew and remove the
upper radiator mounting nuts and washers
(see illustration). Unscrew and remove the
lower mounting bolts and washers and
withdraw the radiator from under the vehicle
(see illustration).11On all later models, the radiator is secured
to the engine compartment front panel using
clips and locking pegs. To release the top of
the radiator, work through the cut-outs in the
engine compartment front panel and remove
the two radiator upper locking pegs (see
illustration). Working under the front of the
vehicle, remove the two radiator lower
mounting bolts. Support the radiator from
underneath. Squeeze the upper radiator
locking pegs to release them from the engine
compartment front panel and lower the
radiator assembly from the vehicle.
Refitting
12Refitting is a reversal of removal, bearing
in mind the following points.
13Refill the cooling system.
14On automatic transmission models, check
and if necessary top-up the transmission fluid
level.
1If the radiator has been removed because
of suspected blockage, reverse-flush it.
2Clean dirt and debris from the radiator fins
using an air jet or water and a soft brush. Be
careful not to damage the fins or cut your
fingers.
6Radiator -inspectionand
cleaning
5Radiator - removal and refitting
4Cooling system - filling
3Cooling system - flushing
2Cooling system - draining
Cooling, heating and air conditioning systems 3•3
3
5.10a Radiator and cooling fan shroud
upper mountings
A Radiator mounting nut
B Shroud securing screw
C Shroud securing clips
D Radiator top hose clip
5.11Removing a radiator upper locking peg5.10b Lower radiator mounting bolt
5.9 Unscrew the fan shroud/radiator
retaining nuts

DOHC models
6Disconnect the battery negative lead.
7To provide additional clearance when
removing the cooling fan shroud assembly
(which is removed from below the vehicle),
apply the handbrake, then jack up the front of
the vehicle and support it securely on axle
stands (see “Jacking and Vehicle Support”).
8Disconnect the wiring plug(s) from the
motor(s), and where applicable, unclip the
wiring from the fan shroud.
9Unclip the expansion tank hose from the
fan shroud.
10Unscrew the two nuts securing the fan
shroud to the top of the radiator, then tilt the
top of the shroud away from the radiator, and
lift the shroud to release the lower securing
clips. Withdraw the assembly from below the
vehicle.
11To remove the fan blades, prise the
securing clip from the end of the motor shaft.12The motor can be separated from the fan
shroud by unscrewing the three securing nuts
and bolts.
13Where two cooling fans are fitted, both are
secured to the shroud in the same manner.
14Refitting is a reversal of removal, but
when fitting the fan blades, ensure that the
drive dog on the motor shaft engages with the
slot in the rear of the fan blades.
On CVH models, the cooling fan switch is
located on the right-hand side of the
thermostat housing (see illustration). On
DOHC models, the switch is located in the
end of the thermostat housing.
Removal and refitting of the switch is as
described for the temperature gauge sender.
Removal
1With the engine cold, slowly unscrew the
expansion tank cap to release any remaining
pressure from the cooling system. Remove
the cap.
2Place a suitable container beneath the
expansion tank.
3Disconnect and plug the upper hose.
4Where applicable, disconnect the coolant
level sensor wiring plug. 5Unscrew the expansion tank securing
screws, and tilt the tank so that the coolant
runs to the sealed end.
6Disconnect and plug the lower hose.
7Drain the expansion tank into the container
and remove the tank.
8Where applicable, the coolant level sensor
can be removed from the tank by unscrewing
the collar from the sensor, then withdrawing
the spacer, sensor and seal (see illustration).
Renew the seal if necessary. Note that the
sensor can only be fitted in one position (see
illustration). Refitting
9Refitting is a reversal of removal.
10On completion, top-up the coolant level to
the maximum mark, then refit the expansion
tank cap and run the engine at a fast idling
speed for several minutes. Check the
expansion tank for leaks, then stop the engine
and if necessary top-up the coolant level.
Removal
1On SOHC models, the temperature gauge
sender is located on the front left-hand side of
the cylinder head, just in front of the inlet
manifold. On CVH models, the sender is
located on the front face of the inlet manifold,
next to the thermostat housing. On DOHC
models, the sender is located at the front of
the inlet manifold (see illustration).
16Temperature gauge sender
- removal and refitting
15Expansion tank and coolant
level sensor - removal and
refitting
14Cooling fan switch -removal
andrefitting
3•8Cooling, heating and air conditioning systems
13.2 Fan blade securing clip and direction
of rotation arrow
15.8a Removing the coolant level sensor
from the expansion tank
16.3a Disconnect the temperature gauge
sender wiring - SOHC16.1 Temperature gauge sender location
(arrowed)16.3b Disconnect the temperature gauge
sender wiring - CVH
15.8b Fitting the coolant level sensor
14.1 Disconnecting the wiring plug from
the cooling fan switch

1With the heater unit removed from the
vehicle, remove the two securing screws and
withdraw the heater matrix from the casing
(see illustrations).
2Cut the heater casing gasket in line with the
casing joint, then use two suitable
screwdrivers to prise off the retaining clips
and separate the casing halves. Withdraw the
lower part of the casing to the side.
3Remove the air flap valves, then press the
control levers from the casing. Note that the
“up/down” control lever can only be removed
when the marks are aligned as shown (see
illustration).
4Clean all components and hose through the
matrix to remove any debris. If necessary usea chemical cleaner to clear the inner passage
of the matrix. Renew the components as
necessary.
5Reassembly is a reversal of dismantling.
Removal
1Disconnect the battery negative lead.
2Where necessary, unclip the brake servo
vacuum hose for improved access.
3On models from 1987, unclip the
windscreen washer hoses and wiring from the
motor cover, and secure them to the
bodywork out of the way.
4Unscrew the two securing bolts from the
motor cover, pull off the rubber moulding,
then withdraw the cover (see illustration).
5Disconnect the wiring from the motor, and
detach the earth lead from its bracket. 6Unscrew the two motor securing nuts, and
withdraw the motor assembly (see illustration).
7Unclip the casing halves, then prise open
the motor retaining strap using a screwdriver,
or if necessary a drift.
8Detach the wiring from the motor, then
remove the motor and fan wheels from the
casing. Refitting
9Refitting is a reversal of removal.
1Only those items which can be renewed
without discharging the system are described
here(see illustration).Other items must be
dealt with by a Ford dealer or air conditioning
specialist.
21Air conditioning system -
component renewal
20Heater motor - removal and
refitting
19Heater unit - overhaul
3•10Cooling, heating and air conditioning systems
19.1a Remove the securing screws . . .19.3 Heater “up/down” control lever must
be aligned as shown before removal
Note that the cross marks are for right-hand
drive vehicles
1 De-ice thermostat
2 Evaporator
3 Expansion valve
4 Compressor
5 Compressor clutch6 Pressure switch
7 Sight glass
8 Dehydrator/collector
9 Cooling fan
10 Condenser
21.1 Layout of air conditioning system components
20.6 Heater motor and wiring
20.4 Unscrew the securing bolts and
withdraw the heater motor cover
19.1b . . . and withdraw the heater matrix

Compressor drivebelt
2Disconnect the battery negative lead.
3On SOHC models, remove the thermo-
viscous cooling fan.
4Slacken the compressor mounting and
pivot bolts, move the compressor towards the
engine and remove the old drivebelt (see
illustration).
5Fit the new drivebelt, position the
compressor to achieve the correct belt
tension, then tighten the mounting and pivot
bolts.
6On SOHC models, refit the thermo-viscous
cooling fan.
7Reconnect the battery negative lead.
Condenser fan and motor
Models up to 1987
8Disconnect the battery negative lead, and
remove the radiator grille. On Ghia models,
remove the front bumper.9Disconnect the fan wiring connector at the
side of the condenser.
10Remove the three securing bolts and
withdraw the fan assembly. Turn the frame to
position the fan wiring on the dehydrator side
to avoid damaging the wiring. Take care also
not to damage the condenser fins or tube.
11To remove the fan blades from the motor,
remove the retaining nut and circlip. The nut
has a left-hand thread, ie, it is undone in a
clockwise direction.
12With the blades removed, the motor can
be unscrewed from the frame.
13Reassemble and refit in the reverse order
of dismantling and removal.
Models from 1987
14Disconnect the battery negative lead.
15Remove the bonnet lock.
16Unclip the guard from the fan frame.
17Disconnect the fan wiring connector (see
illustration).
18Apply the handbrake, jack up the front of
the vehicle and support on axle stands (see
“Jacking and Vehicle Support”).
19Unscrew the two lower condenser
securing bolts and disengage the condenser
from the top of the radiator by releasing the
three clips.
20Unscrew the four securing bolts and
detach the fan assembly from the condenser.
Withdraw the fan assembly from underneath
the vehicle.
21Proceed as described in paragraphs 11 to
13 inclusive.
De-ice thermostat
22Disconnect and remove the battery.23Disconnect any vacuum hoses,
windscreen washer hoses and electrical
wiring as necessary, then unscrew the four
securing bolts and on models up to 1987 the
single nut, and remove the right-hand plenum
chamber cover plate from the bulkhead.
24Disconnect the thermostat from the
evaporator casing and withdraw it. Also
withdraw the thermostat probe from the
casing.
25Refitting is a reversal of removal.
Heating/air conditioning controls
26The procedure is similar to that described
for the heater controls but additionally the
vacuum hoses must be disconnected from
the control unit vacuum valve during removal,
and reconnected when refitting.
Cooling, heating and air conditioning systems 3•11
3
21.17 Air conditioning condenser fan
wiring connector location (arrowed) -
models from 198721.4 Typical air conditioning compressor
mounting and pivot bolts (arrowed)