seats FORD SIERRA 1988 2.G Suspension And Steering Workshop Manual

7Working in the engine compartment,
unscrew the strut upper mounting nut, at the
same time supporting the strut from below.
Use a 6 mm Allen key inserted in the end of
the strut piston rod to prevent the rod from
turning as the upper mounting nut is
unscrewed (see illustration). On some
models, the upper mounting nut may be fitted
with a plastic cover. Note the upper mounting
cup under the nut.
8Withdraw the strut from under the wing of
the vehicle.
Overhaul
9To dismantle the strut, proceed as follows.
10Using spring compressors, compress the
coil spring. Do not attempt to compress the
spring without using purpose-made spring
compressors, as the spring is under
considerable tension, and personal injury may
occur if it is suddenly released (see
illustration).
11Hold the piston rod as described in
paragraph 7, unscrew the nut from the pistonrod and remove the lower cup, bearing, spring
seat, gaiter, coil spring and bump stop (see
illustration).
12Working in the engine compartment,
remove the upper cup and nylon spacer, and
if required prise out the rubber insulator.
13Clean all the components and examine
them for wear and damage. Check the action
of the shock absorber by mounting it vertically
in a vice and operating the piston rod several
times through its full stroke. If any uneven
resistance is evident, the shock absorber
must be renewed. Renew any worn or
damaged components as applicable.
Refitting
14Reassembly and refitting is a reversal of
dismantling and removal, bearing in mind the
following points.
15When reassembling, ensure that the gaiter
is fitted over the bump stop, and that the ends
of the coil spring are correctly located on the
spring seats. Also ensure that the bearing is
correctly located on the upper spring seat.
16Fit the nylon spacer over the piston rod
before fitting the strut to the top mounting.
17Tighten all fixings to the specified torque.
18On P100 models align the previously
made marks on the roadwheel and wheel
stud.Note: A balljoint separator tool will be
required for this operation.
Removal
1Loosen the relevant front roadwheel nuts,
apply the handbrake, jack up the front of the
vehicle and support on axle stands (see
“Jacking and Vehicle Support”).
2Remove the roadwheel. On P100 models
mark the position of the roadwheel in relation
to one of the wheel studs before removal.
3Remove the front brake caliper but do not
disconnect the hydraulic hose. Support the
caliper on an axle stand, or suspend it with wire
from the coil spring to avoid straining the hose.
4Mark the position of the brake disc in
relation to the drive flange, and on Saloon,
Hatchback and Estate models, remove the
retaining screw or spire washer(s), as
applicable, and remove the disc. On P100
models, unscrew the five retaining nuts and
remove the wheel adapter plate and disc.
5Where applicable, unbolt the ABS wheel
sensor from the hub carrier and unplug the
wiring connector. Place the sensor to one side.
6Remove the split pin and unscrew the
castellated nut securing the tie-rod end to the
hub carrier. Using a balljoint separator tool,
disconnect the tie-rod end from the hub carrier.
7Repeat the procedure given in the previous
paragraph for the lower arm-to-hub carrier
balljoint.
8Unscrew and remove the pinch-bolt which
secures the hub carrier to the strut (see
illustration). Using a suitable lever, such as a
cold chisel, lever the hub carrier clamp legs
and wedge them apart. Withdraw the hub
carrier from the strut.
Refitting
9Refitting is a reversal of removal, but use
new split pins on the castellated nuts, and
align the previously made marks on the brake
disc and hub. Tighten all fixings to the
specified torque.
10On P100 models align the previously
made marks on the roadwheel and wheel
stud.
5Front hub carrier -removaland
refitting
Suspension and steering 11•5
11
5.8 Unscrewing the hub carrier-to-strut
pinch-bolt
4.11 Cross-section of the front strut upper mounting
A Bearing
B Nylon spacer
C Upper cupD Rubber insulator
E Lower cup
F Spring seatG Bump stop
H Gaiter
4.10 Suspension strut fitted with spring
compressors
4.7 Hold the strut piston rod with a 6 mm
Allen key when unscrewing the upper
mounting nut

pivot pin. Take care not to lose the
components (see illustration).
5Remove the brake cable sheaths from their
brackets on the vehicle underbody.
6Unscrew the brake pipes from the brake
hoses at the brackets on the vehicle
underbody. Plug the ends of the pipes and
hoses to prevent leakage and dirt ingress,
then detach the hoses from the brackets by
removing the U-shaped retaining clips (see
illustration).
7Where applicable, disconnect the ABS
sensors, and detach the leads from the clips
on the lower arms.
8Place suitable blocks beneath the rear
wheels, then lower the vehicle so that the rear
coil springs are lightly loaded. Reposition the
axle stands under the side members.
9Support the final drive unit with a jack,
using an interposed block of wood to spread
the load.
10Where applicable, unscrew and remove
the two anti-roll bar mountings from the
underbody.
11Unscrew and remove the three bolts
securing each of the front guide plates to the
underbody and the suspension crossmember
(see illustration). Where applicable, bend
back the lockwasher tabs on the larger bolts.
12Unscrew and remove the four bolts
securing the final drive unit rear mounting to
the underbody. Note the location and number
of any shims which may be fitted (see
illustration).
13Working inside the rear of the vehicle,
disconnect the shock absorber upper
mountings. On Saloon and Hatchbackmodels, access is gained by removing the
trim covers behind the side cushions. Each
cover is secured by two self-tapping screws,
and the shock absorber is secured by a bolt
and nut. On Estate models, fold down the rear
seat backrest, fold back the floor covering
and remove the front section of the luggage
compartment floor, which is secured with 12
self-tapping screws. Remove the nut and
washer from the shock absorber.
14Using a jack and a wooden beam
positioned beneath the longitudinal
underbody side members, raise the rear of the
vehicle until the rear suspension and final
drive unit assembly can be withdrawn from
under the vehicle.
15If desired, the assembly can be
dismantled with reference to the relevant
Sections of this Chapter and Chapter 9.
Refitting
16Refitting is a reversal of removal, bearing
in mind the following points.
17Where applicable, secure the larger front
guide plate bolts by bending up the
lockwasher tabs.
18Ensure that the coil springs are located
correctly on their seats on the vehicle
underbody.
19When refitting the final drive rear mounting
to the underbody, refit any shims in their original
noted positions, and fit the bolts with reference
to the note at the beginning of this Section.
20Tighten all fixings to the specified torque.
21On completion, bleed the brakes and
adjust the handbrake. With the vehicle level,
check the final drive unit oil level.
Models with rear drum brakes
Removal
1Chock the front wheels, jack up the rear of
the vehicle and support on axle stands placed
under the side members.
2Remove the relevant driveshaft.
3Remove the handbrake cable from the clip
on the lower arm.
4Unscrew the brake pipe from the brake
hose at the bracket on the lower arm. Plug the
ends of the pipe and hose to prevent leakage
and dirt ingress, then detach the hose from
the bracket by removing the U-shaped
retaining clip (see illustration).
5Unscrew the brake pipe from the wheel
cylinder on the brake backplate and plug the
end of the pipe and the cylinder to prevent
leakage and dirt ingress.
6Unscrew the bolts securing the brake
backplate to the lower arm and tie the
backplate to one side.
7Where applicable, prise the anti-roll bar
connecting strap from the lower arm.
8Support the lower arm on a jack, and raise
it slightly to place the coil spring under load.
9Remove the shock absorber.
10Unscrew and remove the three bolts
securing the front guide plate to the
underbody and the suspension crossmember
(see illustration). Where applicable, bend
back the lockwasher tab(s) on the larger bolt.
11Lower the lower arm, and remove the coil
spring and rubber cup.
12Note the orientation of the two lower
arm-to-crossmember pivot bolts and nuts,
then unscrew and remove them and withdraw
the lower arm from under the vehicle (see
illustration).
13If the lower arm is to be renewed, unclip
the brake pipe, and refit to the new arm.
14If required, the pivot bushes may be
renewed using a long bolt, nut, washers and a
suitable metal tube. Lubricate the new bushes
with soapy water before fitting.
11Rear suspension lower arm
(Saloon, Hatchback and
Estate models) -removaland
refitting
11•8Suspension and steering
10.4 Handbrake equaliser-to-operating rod
circlip and pivot pin (arrowed)10.11 Rear suspension front guide plate -
lockwasher arrowed
11.4 Brake pipe bracket on lower arm. U-
shaped retaining clip arrowed10.12 Final drive unit-to-underbody rear
mounting
10.6 Rear underbody brake pipe bracket -
U-shaped hose retaining clip arrowed

Refitting
3When refitting the fluid hoses, use new
O-rings, and take care not to overtighten the
unions. Note that with the unions fully
tightened it is still possible to rotate and move
the hoses.
4On completion of refitting, bleed the power
steering fluid circuit (Section 34).
Note: New power steering fluid hose O-rings
will be required when refitting.
All engines except 1.8 litre (R6A)
CVH and 2.0 litre DOHC
1Place a suitable container under the power
steering pump, unscrew the fluid hose unions,
and drain the fluid. Ensure that fluid is not
allowed to spill onto the alternator.
2Remove the drivebelts and unbolt the
power steering pump pulley if necessary to
ease removal.
3Unbolt the rear support bar from the pump
and the engine block (see illustration).
4Unbolt the pump from its mounting bracket,
and withdraw the pump from the engine.
5Refitting is a reversal of removal, noting the
following points.
6Tension the drivebelts correctly.
7When refitting the fluid hoses, use new
O-rings, and take care not to overtighten the
unions. 8On completion of refitting, bleed the power
steering fluid circuit.
1.8 litre (R6A) CVH engine
9The removal and refitting procedures are
basically the same as described below for the
2.0 litre DOHC engine, except that the pump
is mounted on a bracket above the alternator
on the front left-hand side of the engine.
2.0 litre DOHC engine
10The pump is mounted on a bracket on the
front right-hand side of the cylinder block.
11Place a suitable container under the
pump, unscrew the fluid pipe unions, and
drain the fluid.
12Remove the drivebelt which also drives
the coolant pump and alternator.
13Prevent the pulley from rotating using a
strap wrench (which can be improvised using
an old drivebelt and a large socket and
wrench), and unscrew the three pulley
securing bolts. Withdraw the pulley.
14Unscrew the three pump securing bolts
from the front of the pump bracket, and the
single bolt from the rear of the bracket, and
withdraw the pump (see illustrations).
15Refitting is a reversal of removal, bearing
in mind the following points.
16Reconnect the fluid unions using new O-
rings.
17On completion, bleed the power steering
fluid circuit.
Note: New fluid hose O-rings will be required
when refitting.
Removal
1Clean around the hose unions on the
steering gear. Place a suitable container
beneath the steering gear, then remove the
single bolt securing the hoses to the pinion
housing, unscrew the hose unions and drain
the power steering fluid.
2Clean around the hose unions on the pump.
Place a suitable container beneath the pump,
unscrew the hose unions, and drain any
remaining fluid. Ensure that no fluid is allowed
to spill onto the alternator.3If the hoses are to be left disconnected for a
long period of time, plug the ends of the
hoses and the apertures in the steering gear
and pump, or cover them with masking tape
to prevent dirt ingress.
Refitting
4Refit in reverse order using new O-rings.
5On completion top-up the fluid and bleed
the system.
1Unscrew the filler cap from the power
steering pump reservoir and top-up the fluid
level to the maximum mark using the specified
fluid.
2Disconnect the low tension negative lead
from the ignition coil and crank the engine
several times for two second periods while
slowly turning the steering wheel from
lock-to-lock. Top-up the fluid level if
necessary and continue cranking the engine
until the fluid is free of air bubbles.
3Reconnect the coil lead and start the
engine. Check the system for leaks.
4Switch off the engine and refit the filler cap.
5Drive the vehicle for a few miles to warm up
the fluid and expel any remaining air, then
stop the engine and make a final fluid level
check.
1Remove the tie-rod end.
2Unscrew and remove the tie-rod end
locknut from the tie-rod.
3Remove the clips and slide the gaiter from
the tie-rod and steering gear.
4Slide the new gaiter over the tie-rod and
onto the steering gear. Where applicable,
make sure that the gaiter seats in the cut-outs
in the tie-rod and steering gear.
5Secure the gaiter with new clips.
6Refit the tie-rod end locknut to the tie-rod.
7Refit the tie-rod end.
Note: A balljoint separator tool will be
required for this operation.
Removal
1Loosen the relevant front roadwheel nuts,
apply the handbrake, jack up the front of the
vehicle and support on axle stands.
2Remove the roadwheel. On P100 models
mark the position of the roadwheel in relation
to one of the wheel studs before removal.
3Make alignment marks on the tie-rod and
tie-rod end, then loosen the locknut by a
quarter of a turn.
33Tie-rod end - removal and
refitting
32Steering gear rubber gaiter -
renewal
31Power steering fluid circuit
- bleeding
30Power steering fluid hoses
- removal and refitting
29Power steering pump
- removal and refitting
11•18Suspension and steering
29.3 Power steering pump rear support bar
bolts (arrowed)
29.14b Power steering pump rear securing
bolt29.14a Unbolt the power steering pump
pulley for access to the front pump
securing bolts (arrowed)