tire type FORD SIERRA 1989 2.G XR4 Workshop Manual

Engine & Related Items
2.5mm metallic inductance EMI
suppressed conductor: with
stainless steel windings spaced
over ferrimagnetic core
substrate
serves as
strength
member for
cable assembly
ignition cables have a non-layered high strenght insulating
jacket made entirely of aerospace grade silicone rubber to
prevent swelling and splitting at extreme trmperatures
KV85 & R-100
metallic inductance EMI
suppressed conductor
pA Performance Air Filters A quick and easy performance modification
is to replace the standard air filter with a direct fit KN high performance air filter.
Merkur XR4Ti (2.3L Turbo)M22P
Merkur Scorpio (2.9L V-6)G22P
pB
High Temp Fyre Sleeve The under hood temperatures on the XR4Ti can
be quite severe. Slipping a length of fyre sleeve over critical wiring or rubber water
& A/C hoses will add an extra degree of protection. Fyre Sleeve provides radiant heat
protection up to 800 degrees. Sleeve is sold per foot and is sized by internal diameter.
Hoses or wiring can be disconnected at one or both ends then slipped through fyre
sleeve or sleeve can be un-stitched at the seam and wire tied in place.
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot320510
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot320512
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot320516
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot320520
pC
Engine Mount Insulators BAT has an alternative to the recently
discontinued original equipment Ford motor mounts on the XR4Ti. Simply
remove the old motor mount assemblies, discard the worn-out rubber
portion, and reuse the top and bottom metal plates with our replacement
insulators.
Note: slight modification requires 10mm holes in plates to be
increased to 12mm. Scorpio mounts are Ford mfg. direct replacements.
Engine Mount Insulator (left & right same) XR4TiM433
Engine Mount Insulator (left & right same) Scorpio-
new FordG433
pD
Transmission Mount /Insulator Rear transmission mount/insulator-
direct fit for automatic & manual Scorpio. A heavy duty version also available.
Note:
this "square" type mount can be fitted to the XR4 with special crossmember, (see
below) as the standard "round" trans. mount used on our XR4Ti's is no longer available.
Transmission Mount Insulator*- (automatic & manual) G433T
Transmission Mount Insulator H.D*.- (automatic & manual) M433TA
*can be fitted to XR4 with additional x-member (see below)
pE Transmission Crossmember Wide and narrow type transmission
tunnel crossmenbers allow the above "square" mount/insulators to be installed in
the XR4Ti. Fitting the XR with this crossmember/mount combination is a consider-
able upgrade (strength, noise, vibration) over the USA supplied "round" mount.
Crossmember* XR4 (wide) 1987-89- manual & auto M433XL
Crossmember* XR4 (narrow) 1985-86- manual & autoM433X
*for use in combination with above G433, M433 "square" type mount
pF Engine Belts H.D. Our search for the ultimate heavy duty engine
accessory v-belts lead us to the top cog "Gold Series" by Dayco. Top cog v-
belts are built to last up to 20% longer than conventional belts. A unique cogged
design increases flexibility and airflow around the belt for reduced friction and
heat. Laminated design with high temperature rated polyester cords provide
maximum tension holding (reduced slip) over the life of the belt.
Belt- XR4Ti (1985-89) W. Pump, Alt, P. Steering (2 required)M6G
Belt- XR4Ti (1986-89) A/C CompressorM6H
Belt- XR4Ti (1985) A/C CompressorM6HA
Belt- Scorpio (1988-89) Fan & Power Steering (2 required)G6G
Belt- Scorpio (1988-89) AlternatorG6GA
Belt- Scorpio (1988-89) A/C CompressorG6H
pG
Performance Ignition Wire Sets We have tried a number of
different ignition wire options on the 2.3 Turbo and 2.9L V6 engines and have
found the Magnecor brand to offer superior quality, performance, and durability.
Cables are red in color with 8mm, 8.5mm and 10mm cable diameters.
Merkur XR4Ti (2.3L Turbo)
Ignition Wire Set- (8mm w/silicone jacket and boots)L9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)M9HT
Ignition Wire Set- (10mm R-100 wire w/silicone jacket and boots)M9HTR
Merkur Scorpio (2.9L V6)
Ignition Wire Set- (8mm w/silicone jacket and boots)G9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)G9HT9 pG
pF
pA
Aluminized Mylar Fyre Sleeve
pB
pC pD
pE
2 7