light FORD SIERRA 1990 2.G XR4 Workshop Manual

Suspension
pC Camber Shims
pD Front
Strut Tower Brace
pE RearpA
Suspension Packages -XR4
Below is a listing of shock and spring packages available as engineered
suspension packages. Fixed rate or adjustable shocks are supplied as noted.
More information on the shocks that make up these kits is listed elsewhere in
the front and rear suspension sections. Kits are available with either -25mm
or standard ride height sport springs- your choice same price !
Spax Sport Gas Shocks & Sport Springs (-25mm or Standard) M400S
* supplied with fixed rate high performance gas shocks
Bilstein Gas Shocks & Sport Springs (-25mm or Standard) M400B
* supplied with fixed rate high performance gas shocks
Spax Sport Adjust Shocks & Sport Springs (-25mm or Std.) M400A
* supplied with adjustable high performance gas shocks
pB Sport Spring Sets -XR4
Our specially designed progressive rate sport springs will minimize body "roll" while
cornering and reduce "dive" under hard braking. Progressive springs are designed to
become stiffer as they are compressed allowing for a smooth transition between (very
reasonable) straight line comfort and high performance cornering. We recommend
the standard height or -25mm ride height sets for all around performance street and
light competition use, the -40mm springs should be considered for only racing/
competition use. Take into account when lowering your cars ride height that additional
negative camber will be added to the front and rear suspension angles. This is usually
not a problem on the front end, however, cars that are already experiencing noticeable
wear on the inside edges of the rear tires at "standard" ride height will see this increase
when lowering. This condition can be corrected if necessary by using camber shims
(kit available below) at the rear spindle mount to adjust for excessive negative camber.
Notes: Defining "standard" ride height is difficult on the XR4 as the springs on many
cars have already "sagged" 1/2 to 3/4 of an inch since new. In this case if the front
and rear tires are still wearing normally lowering the car another 1/4" or 1/2" (over what
it is currently) should not adversely effect tire wear.
Sport Spring Set -25mm (front & rear) XR M414M
Competition Spring Set -40mm (front & rear) XR M414C
Sport Spring Set*
Standard Height (front & rear) XR M414S
See Price List For Scorpio Spring Applications
pC Rear Camber Shim Kit -XR4
To correct rear camber angles on cars that have excessive negative camber
we offer a handy rear spindle shim kit. This kit is sometimes necessary on cars
with lowered sport springs, but can also be used to correct camber on cars with
"sagging" stock rear springs. The components (instructions and shims)
needed to space the rear bearing spindles between the brake backing plates
are supplied. This camber kit will add roughly 1.5 degrees of positive camber
and adjust rear toe back with in standard range as well.M423R
pD
Front Strut Tower Brace -XR4
The XR4 has a well built chassis structure that does not exhibit much flex
under normal conditions. With the addition of high performance tires and
suspension parts more stress is put on the front strut towers causing some
deflection under hard cornering which will eventually weaken the structure
and lead to unpredictable handling characteristics. Connecting the front strut
towers by adding a upper stressbar (strut tie bar) will improve chassis
stiffness and keep the suspension angles constant under hard use condi-
tions. For this purpose we offer a lightweight aluminum front tower brace
(stressbar) that incorporates a removable tubular cross brace and cast alloy
turret mounts. Highly recommended for cars that are used for track events,
drivers schools, auto-cross and spirited road use.M403F
pE
Rear Shock Mount Brace XR4
Our rear (stressbar) is a nicely finished lightweight tubular aluminum rear
brace which is just the thing for linking left and right hand upper shock mounts.
A slight bit of plastic trimming is required when fitting. Bars are supplied with
an attractive blue finish.M403R

(less expensive steel version of above) M403RS pA
Suspension Packs
0 3
pB Sport Spring Sets

pA Sway Bar Bushings H.D. Urethane sway bar bushings in 25mm for
standard XR4 and 28mm for larger Sierra Cosworth or Scorpio sway bars.
Note: XR4Ti and Scorpio sway bar clamps differ slightly making the bushings
non-interchangeable. XR's that require replacement bar clamps (see below) will
then require Scorpio type bushings to match. (bushings sold each)
Bar Bushing H.D. 25mm- (direct fit) XR4 M407BU
Bar Bushing H.D. 28mm- (direct fit) XR4 M407BAU
Bar Bushing H.D. 25mm- (special) XR4 with G407C clampG407BA
Bar Bushing H.D. 28mm- (direct fit) Scorpio G407BAU
pB
Sway Bar Bushing Clamps The European type sway bar bushing
clamp (used on Scorpio & Cosworth) has a groove to receive a ridge back
type bushing. Clamps are a direct replacement for Scorpio and can also be
used to replace worn or broken clamps on XR4 with correct bushings (see
above).
(2) required- sold each
Sway Bar Bushing Clamp (each)- Scorpio G407C
pC
Steering Rack Complete ZF type rack assemblies include inner tie
rods, boots, and stainless steel inner sleeve.
Steering Rack Assembly- XR4 M434SR
Steering Rack Assembly- Scorpio G434SR
Steering Rack Bushing Standard and H.D. (urethane) rack bushings
(2) required (sold each)
Steering Rack Bushing (each)- XR4 & Scorpio M434B
Steering Rack Bushing H.D (each)- XR4 & Scorpio M434BH
pD
Inner Tie Rod High quality European Ford inner tie rods available
for XR4 and Scorpio.
(sold each)
Inner Tie Rod- XR4Ti M434TK
Inner Tie Rod- Scorpio (left & right same) G434TK
pE
Rack Boot All rubber steering rack bellows (boots). Suitable for both
XR4 and Scorpio.
(left & right rack boots same- sold each)
Steering Rack Boot (each) -XR4 & Scorpio M434RB
pF Outer Tie Rod End High quality European Ford outer tie rod ends
available for XR4 and Scorpio.
(each)
Tie Rod End- XR4 (left) M434L
Tie Rod End- XR4 (right) M434R
Tie Rod End- Scorpio (left & right same) G434
pG
Power Steering Pumps Direct fit, replacement power steering
pumps for XR4 and Scorpio applications.
(core charge required)
Power Steering Pump- XR4Ti (integral reservoir type) M434P
Power Steering Pump- XR4Ti (remote reservoir type) M434PA
Power Steering Pump- Scorpio (all) G434P
pH
P/S Pressure Hose We have these hard to find pressure side hoses
available for all model year XR4Ti's.
P/S Pressure Hose- XR4Ti (all years) M434PH
pI
Strut Boot/Bump Stop These H.D. strut boot/bump stops help
reduce the chance of strut damage due to over-compression and/or strut rod/
seal damage from dirt and corrosion. A specially designed one piece bellows
with integral (NBR),"nitrile butadiene", variable rate bump rubber make these
especially well suited for lowered ride height suspensions.
(sold each)
Strut Boot/Bump Stop (each) -XR4 & Scorpio M405B
Front Strut Rotating Bearings
Upper Rotating Bearing (each) -Scorpio G403
Upper Rotating Bearing (each) -XR4M403
pF pC
pEpD
Suspension & Steering
pA/B
0 4
pI
pH pG

pC
pDpBpA
pA Front Brake Special 260 x 24mm
This kit is just the thing for replacing the standard size, wear related,
front brake components. We supply high quality Euro specification
rotors and premium Mintex brake pads for either XR4 or Scorpio and
at a special price as compared to buying items separately.
Front Brake Special XR4ti M420SP
Front Brake Special Scorpio G420SP
pB
BAT R/S Front Brake Kit (283 x 24mm) XR4ti
BAT R/S Brake Kit allows larger 11.25" (283mm) Cosworth brake
rotors to be fitted with standard XR calipers. Increasing rotor "swept
area" in this way will greatly improve stopping power (leverage) and
help to reduce high brake temperatures that can cause premature
brake fade and poor pedal feel. Kits are available in 4 different
component levels from as little as $295.00, which leaves you no
reason not to upgrade to larger brakes.
Kits include: 285 x 24mm
vented (standard or cross-drilled) rotors, Mintex brake pad set
(standard or M1144), caliper mounting brackets & hardware (fitment
with most 15" and larger wheels -some require modification or
spacers)
Front R/S Brake Kit (283 x 24mm) M417
includes standard rotors, standard Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M417A
includes X-drilled rotors, standard Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M418
includes standard rotors, M1144 Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M418A
includes X-drilled rotors, M1144 Mintex pads, brackets & hardware
pC BAT/Wilwood Front Brake Kit (283 x 24mm) XR4ti
This kit combines the performance of the larger 283mm Cosworth rotor
with Wilwood 4 piston Superlite 2A calipers which are extremely ridged
and transfer torque directly without unwanted flex. Construction is
aluminum with stainless pistons for both weight savings and maximum
head dissipation. At just 5 lbs. they are also much lighter than stock
calipers. This goes a long way to reducing "unsprung" weight benefiting
both braking and handling performance.
Kit includes: 285 x 24mm
vented rotors, 4-piston alloy Wilwood Superlite IIA calipers with pads
and aeroquip brake hoses (fitment with most 15" and larger wheels -
some require modification or spacers)
M416W
pD
BAT/Wilwood Front Brake Kit (300 x 24mm) XR4ti
This kit combines even larger 300mm Cosworth rotor with Wilwood
4 piston Billet Dynalite for the ultimate big brake kit. Calipers are
extremely ridged and transfer torque directly without unwanted
flex and are made from aluminum with stainless pistons for both
weight savings and maximum head dissipation. At just 4 lbs. they
are also much lighter than stock calipers. This goes a long way to
reducing "unsprung" weight benefiting both braking and handling
performance.
Kit includes: 300 x 24mm vented rotors , 4-piston
alloy Wilwood Billet Dynalite calipers with pads and aeroquip
brake hoses (fitment with some 15" & most 16" and larger wheels
-some require modification or spacers)
M416W3
Brake Kits & Specials0 8

Brake (related)
pA
pEpA
Racing Brake Fluid Not all brake fluid is created equally. High
operating temperatures at the caliper transfers extreme heat through the piston
causing lesser quality brake fluid to boil. This in turn allows the fluid to become
compressed and reduces overall braking performance. The best way to
counter this from happening is to use a racing specification, mineral (never
synthetic) brake fluid and flush the system after each event for competition or
annually on performance street driven vehicles. Both AP550 and Wilwood 570
brake fluid is DOT approved with a dry boiling point of 550-570 degrees, low
viscosity minimizes aeration and permits easy bleeding.
Brake Fluid AP Competition (16.9oz. 500ml.) MC550
Brake Fluid Wilwood 570 (12oz. 355ml.) MC570
Brake Fluid Wilwood 570 (6 Pack) MC57-6
Brake Fluid Wilwood 570 (24 Case) MC57-C
pB
Cosworth & Scorpio Rotors For those fortunate few who own
Cosworth Sierras or have converted XR4's to Cosworth type front or rear brakes
and are in need of replacement rotors we have them. Scorpio front or rear rotors
in standard and cross drilled are also available. (see price list page 31)
Cosworth Front 283 x 24mm standard, X-drilled, grooved
Cosworth Rear 273 x 10mm standard, X-drilled, grooved
Scorpio Front 260 x 24mm standard or X-drilled
Scorpio Rear 253 x 10mm standard or X-drilled
Performance Brake Kits Engineered competition brake kits for the
ultimate in stopping power.
pC Front R/S Brake Kit (283 x 24mm)
BAT R/S "big brake" kit allows larger 11.25" (285mm) brake rotors to be fitted
with standard XR calipers. Increasing rotor "swept area" in this way will greatly
improve stopping power (leverage) and help to reduce high brake temperatures
that can cause premature brake fade and poor pedal feel.
Kit includes:
285 x 24mm vented (standard or cross-drilled) rotors, Mintex 1144 brake pad
set, caliper mounting brackets & hardware (fitment with most 15" wheels -
some require slight modification)
kit supplied with standard rotors
M418
kit supplied with cross drilled rotors M418A
pD Front Brake Kit (283 x 24mm) w/4 Piston Calipers
Combine the performance of the R/S large rotor kit with 4 piston calipers for the
ultimate in stopping power.
includes: 283 x 24mm vented rotors,
4-piston alloy Wilwood Superlite 2A calipers with pads. (fitment with most 15"
wheels -some require modification or spacers)
M416W
pD Front Brake Kit (300 x 32mm) w/4 Piston Calipers
For those who are looking for the ultimate brake performance. Quite simply the
largest and most competent competition type brake kit that can be fitted to the XR4.
includes: 300 x 32mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite IIA calipers, caliper mounting brackets & hardware
M417A
(this kit also available for Scorpio ! ) G417A
Rear Kit (XR4 w/16" wheels) 300 x 21mm (See Price List)
includes: 300 x 21mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite 2A calipers, caliper mounting brackets & hardware
pE Wheel Bearings Genuine European Ford wheel bearing kits are
complete with all required service parts to do a first class job. Each kit
include bearings, races, seals and hub nuts to service one wheel.
Front Wheel Bearing Kit (specify left or right) -XR4 M560F
Rear Wheel Bearing Kit (specify left or right) -XR4 M560R
Front Wheel Bearing Kit (specify left or right) -Scorpio G560F
Rear Wheel Bearing Kit (specify left or right) -Scorpio G560R
pB
pC
pD
1 0

pA Constant Velocity Joints & Boots The Merkur XR4Ti and Scorpio
independent rear axle assemblys utilize half shafts that have inner and outer constant
velocity joints. Eventually these joints and protective boots will require service. We
have joints and boots available separately making it economical to replace just the
worn component without having to replace whole axle assembly. However, if more
than one C.V. per axle requires service, our complete axle assembly is the more cost
effictive way to go.
Note: right/left inboard and outboard C.V. joints and boots are
interchangeable- see price list for complete axle prices (handed left & right)
Constant Velocity Joint- XR4 & ScorpioM550B
C.V. Boot Kit-
XR4 & ScorpioM550BK
Complete Axle(specify left or right)-
XR4 & ScorpioM550L/R
pB
Rubber Drive Shaft Coupling The rubber "Drive Donut" or "Rotoflex
Coupling" on the XR4 and Scorpio drive shaft can be a real bugger. Many owners
have contacted us after being quoted up to 500.00 to totally replace the complete
drive shaft assembly by the local Ford L/M dealer, as they do NOT list the rubber
drive coupling as a separate service part. We import the proper replacement
drive coupling and make it available at considerable savings to you. If your car
exhibits a driveline shudder that increases with speed, (especially noticeable in
colder weather) we recommend taking a close look at the condition of the drive
coupling. Cracks in the rubber or missing pieces will require immediate replace-
ment, loosing one of these joints at speed will be very messy !
Note: BAT supplies
the standard equipment XR4i drive coupling by the original supplier to Ford. This
is not a lesser "fits all" component that just happens to be similar.
Rubber Drive Shaft Coupling- XR4 & ScorpioM17A
pC
Drive Shaft Center Support Bearing- Replacement driveshaft
center support bearing assemblys for XR4Ti and Scorpio.
Drive Shaft Center Support Bearing- XR4Ti M550SB
Drive Shaft Center Support Bearing- Scorpio G550SB
pD
Quaife Torque Biasing Differential Quaife torque biasing
differentials provide a constant and infinitely variable output to both rear
wheels. These unique differentials utilize a series of helical gears which
sense the amount of applied torque and adjust automatically for loss of
traction. The Quaife limited slip design is also free of high wear items
(clutches, ratchets and plates), making them stronger and more maintenance
free than other types of limited slip units. Anyone who has had the pleasure
of driving a vehicle equipped with a Quaife LSD will immediately comment on
its smooth seamless performance, very unlike clutch/plate type LSD's which
exhibit a notchy ratchet like take up through the drive line. The Quaife LSD
that we offer is originally designed as a replacement upgrade for the Sierra
Cosworth and are now supplied with output flanges tapped for either the large
108mm (Cosworth size) or smaller 100mm (XR4 size) C.V. joints.
Quaife Limited Slip DifferentialM710
pE
Clutch Kits We have a very good selection of clutch packages that include
clutch disk, pressure plate, throw out bearing, and clutch alignment tools. Buying one
of our engineered kits will guarantee best quality, performance, fitment (ease of
installation) and price. First option is a new (not rebuilt or re-lined) O.E. quality
replacement clutch kit by Sachs/Valeo. This clutch is best suited for standard or
slightly modified cars being used under normal driving conditions. If your requirements
are beyond the capabilities of the standard clutch we also have some heavy duty clutch
kit options. H.D. clutch kits include pressure plates that have increased clamping force
(from 30 to 50%) and clutch disks with high temperature friction materials applied.
Centerforce H.D. clutch kits have a unique centrifugal pressure plate design with
substantially more clamping force but requires very little pedal pressure over the stock
clutch.
Note: all kits are for standard transmission 1" 23 spline except where noted.
Sachs Clutch Kit XR - best quality O.E. clutchM519K
Sachs Clutch Kit Scorpio -
best quality O.E. clutchG519K
Sachs Clutch Kit XR w/ T5 Trans -
1 1/16" 10 spline for T-5 transM519T5
H.D. Centerforce Clutch Kit -
uprated disk & 30% p. plateM519C
H.D. Center Force II Clutch Kit -
uprated disk & 50% p. plateM519C2
Clutch Alignment Tool -
1" 23 spline for std. transmissionS11H
Clutch Cable- XR4Ti M562
Clutch Cable- Scorpio G562pD
Driveline
pA
pD pB
pC
1 1

Trim & Lighting
pA European Emblems & Badges Re-badge your XR4 with Ford ovals
and Sierra emblems or put the finishing touches on that Cosworth clone.
Genuine Ford European logos will distinguish your XR4 or Scorpio from the
rest. Location (on car) for emblems and sticker logos are listed below.
Emblems are chrome and black plastic with self stick backing. Stickers can be
applied to metal or glass surfaces.
Sierra (emblem)
rear hatch leftM321S
Sierra XR4i Red (sticker)
rear hatch leftM352R
Sierra XR4i Anthracite/Gray (sticker)
rear hatch leftM352A
Sierra R/S (emblem)
rear hatch leftM321RS
Cosworth (emblem)
rear hatch left under Sierra R/S emblemM321C
Sierra R/S Cosworth (sticker)
rear hatch leftM352C
R/S (emblem)
side fender XR & ScorpioM352RS
Ghia- crest (emblem)
side fender XR & ScoprioM352G
Oval "Ford" (emblem)
front grille center & rear hatch rightC321
"Ghia"- script (emblem) Scorpio rear hatchG352G
2.9i (emblem)
Scorpio rear hatchG352L
Scorpio (emblem)
Scorpio rear door sail panelG352S
pB
European Headlamps The standard US spec. XR4 & Scorpio
headlights were pretty poor when new, and get worse with age- especially when
the lenses turn cloudy. European headlamps will provide a significant increase
in light output and they look great too. These lamps utilize all glass lensing with
a halogen H-4 55/60 watt bulb for high/low main beam operation, and a halogen
H-3 55 watt bulb for the built-in driving lamp.
Note: Lamps are supplied in right hand
drive (English) specification which has a subtle different low beam flair pattern,
however, this is not very noticeable. If required left hand (German) type lenses are
available separately (see price list). We recommend installing the lamps first before
opting to swap out the lenses as most customers do not bother.
Sierra XR4 European Headlamp Kit* M318
*kit includes (2) lamps, rear bulk heads panels, bulbs & wiring instructions
Scorpio* European Headlamp Kit G318
*kit includes (2) lamps, left & right lamp lamps/indicators & front grille sections,
bulbs, and wiring instructions
Scorpio Fog Lamp (LH)- complete replacement assembly G349L
Scorpio Fog Lamp (RH)- complete replacement assembly G349R
pC
Head Lamp Bulbs Replacement and higher wattage bulbs for above
European headlamps and standard XR4 & Scorpio aerolamps. Headlamps- H4
bulbs are fit eurolamps (not stock headlamps), 9004 bulbs are for use with standard
XR4Ti & Scorpio aerolamps. Fog lamps- H3 bulbs are suitable for eurolamps and
Scorpio, 880 bulbs fit
only XR4Ti fogs. Krypton gas 9004 "Bright White" bulbs burn
brighter with more luminous output than standard halogen type bulbs.
"Blue Ion"
bulbs project a, low glare, blue tinted beam- definitely a different look !
H4 55/60 watt (for high/low main beam) Z H4 55/60
H4 55/100 watt (for high/low main beam) Z H4 55/100
H4 80/100 watt (for high/low main beam) Z H4 80/100
H3 55 watt (for fog & driving lamps) Z H3 55
H3 100 watt (for fog & driving lamps) Z H3 100
880 50 watt "Blue Ion" 50 watt (for XR4Ti fog lamps) Z 880/50B
880 50 watt "Amber" 50 watt (for XR4Ti fog lamps) Z 893/50G
9004 "Bright White" 45/65 watt (for high/low main beam) Z 9-45/65W
9004 55/100 watt (for high/low main beam) Z 9-55/100
9004 80/100 watt (for high/low main beam) Z 9-80/100
9004 "Blue Ion" 55/100 watt (for high/low main beam) Z 9-55/100B
Relay (Hella) 12 volt-
(2) required w/ 80/100 bulbsZ Relay12
pD
Rear Tail Lamp Seals & Lamp Sockets Puddles in the trunk or damp
carpeting might be due to leaking rear tail lamp seals. Non-functioning tail
lamps are usually due to corroded lamp sockets. We have new replacements
for both these USA Ford unavailable parts.
Left or Right Tail Lamp
Seal- XR4 M319S
Left or Right Tail Lamp
Socket- XR4 M319LS
H4 H3 9004 pC
pD
pA
(h XR) (Scorpio i)
pB
Scorpio fog lamps
1 4

Wheels
4 Spoke "Turbo" Wheel
Stylish 4 spoke "Turbo" wheel available
in 16" diameter with either a 6" or 6.5"
width. Finish is bright silver. We highly
recommend these factory Ford wheels
for guaranteed quality fit and finish.
Center cap included.
4 Spoke "Turbo" Wheel
16 x 6" $195.00
16 x 6.5" $195.00
2 x 4 Spoke Wheel
Stylish 2 x 4 spoke wheel available
in 16 & 17" diameters from 6.5" to
7.5" widths. Finish is bright silver.
We highly recommend these factory
Ford wheels for guaranteed quality
fit and finish.
Center cap included.
2 x 4 Spoke Wheel
15 x 7" $209.00
16 x 6.5" $209.00
17 x 7.5" $209.00
TW "Thrust" Wheel
10 spoke "Thrust" light alloy
wheel with a locking center
cover. Available in charcoal
grey with polished silver lip in
15 x 7" size. A great looking
wheel at a budget price.
TW "Thrust" Wheel
15 x 7" $109.00
Wheels FYI
We offer only direct fit wheels for the Contour in the 4 x 108mm pattern and 35-40mm offset range. Most
are factory Ford or Ford Motorsport authorized wheels which guarantees quality fit and finish. BAT imports
these wheels directly from Europe and our prices include all inbound freight charges. Outbound freight
from our location to you by UPS ground will cost between 30.00 to 50.00 per set of 4 wheels- depending
on your location. Please note: We often hear horror stories from customers who have ordered wheels
from European mail-order suppliers only to receive damaged or substandard components, and now you
own it! Sending it back or trying to get the freight carrier to pay for the damage is next to impossible they
will just claim it was "improperly packed" or "it wasn't that way when it left here". Worse yet, the shipping
costs involved importing large, heavy, items like wheels can far exceed the cost of the part (expect 50.00
to 100.00 per wheel) What started out as a bargain now has become a expensive learning experience.
Avoid the hassles, let us supply your wheels to your door at a fair
price. When you do the math you will find we are saving you money.
ST200 Wheel
Stylish 14 spoke wheel available in 17" diameter with a 7" width. Factory
equipment on the Mondeo ST200. Finish is bright silver. We highly
recommend these factory Ford wheels for guaranteed quality fit and finish.
Center cap included. (wheel might requite a spacer for XR fitment)
ST200 Wheel 17 x 7" $209.00 each
1 6

Accessories
pA Scorpio R/S Rear Wing This hot looking rear wing goes a long way
in transforming Scorpio's look. For installation R/S wings will require
painting to match your cars color, and some mounting holes from the
standard spoiler will need to be filled and spot painted. Also note that a rear
brake light will need to be located elsewhere in the rear window.G306
Scorpio R/S Side Skirts Matching Rally Sport rocker panel side skirt
set looks great with above rear wing or without. Other than just good
looks, side skirts help to keep the door sides and rockers cleaner and with
less stone chips. Easy to fit, paint and install.G302S
pB Scorpio Cowl Cover What is it, and why doesn't my car have one?
This is a commonly asked question regarding this item. Ford equipped
very few Scorpios bound for the US market with these European cowl
covers. This moulded plastic cover keeps dirt, debris and small animals
from winding up in the ventilation fan and associated duct work. Clean
out this area once and for all, then install a new cowl cover- your Scorpio
will thank you.G369C
pC Mini-Lite Wheels (15" x 7") for XR4 Cars of English heritage,
XR4's included, look great on classic Mini-Lite type wheels. These
wheels are both lightweight and attractive with a bright silver clear coat
finish. Specifications: 4 x 108mm pattern, 15" x 7" size, 38mm offset,
18lbs each, center caps included.M411M
pD Thrust Wheels (15" x 7") for XR4 We are often asked to supply
inexpensive road wheels, and here they are. The Thrust is a 10 spoke
light alloy wheel with locking center cover, available in either silver, or
charcoal w/silver lip. You will not find a better quality, proper wheel
fitment for the price. Specifications: 4 x 108mm pattern, 15" x 7" size,
35mm offset, 18lbs each, locking center covers included.M411T
pE Floor Mats Foul weather mats, commonly referred to as "ice cube
trays" or "waffle mats", are made of heavy duty rubber with small
compartments to catch melting ice, water, mud etc. from your shoes or
boots. These Euro. Ford mats are the best protection for your interior for the
winter months or when going afield. Can be placed over standard plush
mats or directly on carpeting. When dirty or filled with water- remove, drain,
hose off, and reinstall. Front mats will fit both XR4 and Scorpio, rear mats
are for XR4 only.
Front Mat set M1010 Rear Mat SetM1011
First Aid Kits We are often asked to supply the First Aid kits that Ford
equips new cars with in Europe. Includes more than just a selection of
"Band-Aids". Think of it as good insurance.M102
Fuse Box Covers A common breakage item on XR4's. We have new
European Ford replacements.M474
pF Sunroof Wind Deflector The buffeting effect, and wind noise, that
takes place with the sunroof open at speed can be eliminated with a
Sunroof Wind Deflector. Tinted smoke (grey) acrylic, fits both XR4 and
Scorpio- hardware included.M307
pG Side Window Wind Deflector for XR4 A similar product to the
Sunroof Deflector the Side Window Deflector keeps the wind noise levels
to a minimum while allowing maximum ventilation. Effective even in light
rain! Tinted smoke (grey) acrylic, easy installation- no holes to drill. For
XR4 only- sold in pairs.M340WD
pB
pD
pC
pA
pE
pG pF
1 7

Accessories
pApA
Cosworth Sierra Steering Wheel This sporty 3 spoke design
leather wrapped steering wheel is standard factory issue on the Sierra
Cosworth and RS500 models. The smaller wheel diameter (13.9 inch) helps
make the steering ratio more effective and the fatter rim grip offers both comfort
and control. Wheel is available in black and included center horn button with
Ford logo and horn symbol.M322
pB Cosworth Sapphire Steering Wheel This 3 spoke leather wrapped
wheel from the Sierra Sapphire 4x4 steering wheel is a departure on the
original Coswoth version. It's wider center spokes are positioned lower for
comfortable hand position and a better view of the instrumentation. The smaller
wheel diameter (13.9 inch) helps make the steering ratio more effective and the
fatter rim grip offers both comfort and control. Wheel is available in black and
included center horn button with Ford logo and horn symbol.M322A
Standard Horn Button for the standard XR4 steering wheel we have the
European "Ford" oval logo horn button. Just the thing for finishing the interior
off while fitting Ford logos to the exterior.
Z61551
pC Contoured Dash Overlay just the ticket for covering up a cracked
vinyl dash pads which are so common on the XR4 & Scorpio. This moulded
plastic dash overlay is simple to install and covers up a world of sin, quickly
returning the interior to its original splendor.
note: supplied in black can be easily
painted to match interior color
(for XR4) M323

NEW (for Scorpio) G323
pD White Gauge Face Set Colored gauges are quite the rage. They add
a very unique look to the interior, and are easy to read in daylight or when
illuminated at night. We have a gauge face kit that will replace the standard
(black) speedo, tach/boost, fuel and water temp, gauges and indicator lamps
with a thick self adhesive mylar faces that are white in color. These gauge
faces are manufactured specially for BAT by a original equipment instrument
supplier to Ford, GM, Vauxhall so quality is outstanding. They illuminate from
the rear "back light", just as the standard gauges, and will not opaque with age
like typical cheap reproductions will. An added benefit of our gauge face kit
is the speedo is calibrated beyond 85mph all the way to 150mph. Updating
earlier cars with 85mph speedos is a snap.
(available spring 99) M341W
pE
170 mph Speedometer For the owners of land based cruise
missiles we offer the original equipment Sierra Cosworth speedometer
calibrated in mph (170 in white) and kmph (270 in yellow) with re-setable
trip-meter. A slight bit of tweaking is required to fit.
M341A
150 mph Speedometer Sierra XR4's and later Merkurs came with a more
realistic 150 mph speedometer which easily replaces the American (only
calibrated to 85 mph) version.M341
Dash Instrument Panel Bulb lamp with (white) socketM330L
Dash Warning Lamp Bulb lamp with (gray) socketM330WL
pF Torch Key & Battery complete Ford key blank and lamp/battery.
Torch key blanks and lamp batterys are also listed separately below.
C309KL
Torch Key Blank replacement key blank for XR4 (less lamp)Z61179
pG Lamp & Battery lamp and battery for XR4 & Scorpio keysC309KLB
pH Standard Keys as an extra key or an alternative to the more bulky torch
key, this European key blank has a molded plastic grip with wide ring slot with
Ford logo.
(for Scorpio) G309K (for XR4) C309K
Hatch Lock Assembly lock assem. w/housing & 2 keysM815L
Hatch Striker commonly required replacement itemM815S
Hatch Lock Retaining Clip commonly required replacement itemM815C
Complete Car Lock Set doors, hatch, ignition w/ 2 keysM309LS
pD
pE
BRAKE
pF
pHpG pC
pB
turbo
1 8

Accessories (books)
pA The Sporting Fords- Volume 4: Sierras by Graham Robson.
This book has comprehensive information on the development and
history of all Sierra, Sierra Cosworth, and Merkur models. Chapters
include production street and race versions of the cars, technical
information and specifications, buyers and identification guide,
performance figures and much more.
Hard bound 9 1/2" x 7 1/2", 128
pages, 131 black & white illustrations.
M207
pB High Performance Sierras & Merkurs by various authors.
Packed with reprints of magazine articles, road tests of production
and racing cars, data & comparisons, development, specifications,
and tuning. Cars covered in this publication are Sierra, Sierra
Cosworth, RS500, XR 4x4, and Merkur XR4Ti models.
Soft bound 8
1/2" x 11", 172 pages, 200 + black & white illustrations.
M206
pC Classics in Color - Ford Sierra Cosworth by Dennis Foy &
Terry West. A full color profile of the Sierra Cosworth line
including R/S Cosworth, RS500, Cosworth 4x4, and Cosworth
Sapphire. Great color photographs of both production and racing
variants of these unique vehicles.
Soft bound 7 1/2" x 10, 96
pages, 130 color illustrations.
M203
pD Workshop Manual- Sierra 1982-1992 by Haynes. Covers the
European Sierra & Sapphire 4 cylinder models (except Cosworth). Lots
of good information covering repair procedures (light-years ahead of
Chiltons). Most sections, with the exception of the engine, are the same
or similar to the US cars. An inexpensive alternative or addition to the
American Merkur Manual.
Hard bound 8 1/2" x 11 ", 250 pagesM204
pE Workshop Manual- Sierra XR4i (V6) by Haynes. Similar to
above, covers the XR4i & XR4x4 V6 equipped models.
Hard bound
8 1/2" x 11 ", 250 pages
M204A
pF Workshop Manual- Scorpio (V6) by Haynes Covers the
European Scorpio/Granada V6 models- very similar to our US spec cars.
A handy manual to have.
Hard bound 8 1/2" x 11 ", 250 pagesG204
pG Build & Modify Ford V6 Engines by Sven Pruett. A very
well done build and tune book covering the V6 Ford 2.6, 2.8, 2.9, 4.0L
engines.
Soft bound 8 1/2" x 11", 160 pages.G202
pA
pC
pB
pD
pFpE
pG
pH
pH How To Prepare The Sierra For Motorsport by Ford Motor
Company Competition Department & Graham Robson. Complete
guide to race preparing the European specification Sierra for
motorsports competition. Chapters on modifying suspension, body,
engine, driveline, brakes, clutch, and differential- including
specifications and part number listings.
Soft bound 8 1/4" x 11 3/4",
147 pages, 150 black & white illustrations.
M205
Workshop Manual- Sierra & Escort Cosworth origional European
Ford shop manuals (2 volume set) for the Cosworth cars.M202
The Complete 2.3L Turbo EEC-IV Handbook a comprehensive
view of the engineering, performance characteristics, and troubleshooting
for each component of the EEC-IV engine control system.M209
Ford Sierra Cosworth
Dennis Foy & Terry West
(Not Pictured)
2 0