wheel size FORD SIERRA 1992 2.G DOHC Engine Workshop Manual

General
Engine type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four-cylinder, in-line, double overhead camshaft
Engine code:
Carburettor engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N8A
Fuel injection engine without catalyst . . . . . . . . . . . . . . . . . . . . . . . . . N9A
Fuel injection engine with catalyst . . . . . . . . . . . . . . . . . . . . . . . . . . . N9C
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.00 mm
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.00 mm
Cubic capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1998 cc
Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 : 1
Compression pressure at starter motor speed . . . . . . . . . . . . . . . . . . . . 11 to 13 bars
Maximum continuous engine speed:
N8A engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6050 rpm
All engines except N8A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5950 rpm
Maximum engine power (DIN):
N8A engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 kW at 5600 rpm
N9A engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 kW at 5500 rpm
N9C engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 kW at 5500 rpm
Maximum engine torque:
N8A engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Nm at 3000 rpm
N9A engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Nm at 2500 rpm
N9C engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Nm at 2500 rpm
Cylinder bore diameter
Standard class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.000 to 86.010 mm
Standard class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.010 to 86.020 mm
Oversize 0.15 class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.150 to 86.160 mm
Oversize 0.15 class B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.160 to 86.170 mm
Oversize 0.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.500 to 86.510 mm
Chapter 2 Part B:
DOHC engine
Camshafts and cam followers - removal, inspection and refitting . . .21
Crankcase ventilation system - inspection and maintenance . . . . . . .2
Crankshaft and bearings - examination and renovation . . . . . . . . . .31
Crankshaft and main bearings - removal and refitting . . . . . . . . . . . .30
Crankshaft front oil seal - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Crankshaft rear oil seal - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Cylinder head - dismantling and reassembly . . . . . . . . . . . . . . . . . . .19
Cylinder head - inspection and renovation . . . . . . . . . . . . . . . . . . . . .20
Cylinder head - removal and refitting (engine in vehicle) . . . . . . . . . .17
Cylinder head - removal and refitting (engine removed) . . . . . . . . . . .18
Engine/automatic transmission assembly - removal and separation . .8
Engine/automatic transmission assembly - reconnection and
refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Engine dismantling, examination, renovation and reassembly - general
information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Engine/manual gearbox assembly - removal and separation . . . . . . .7
Engine/manual gearbox assembly - reconnection and refitting . . . . .11Engine - refitting (manual gearbox in vehicle) . . . . . . . . . . . . . . . . . . . .9
Engine - refitting (automatic transmission in vehicle) . . . . . . . . . . . . .10
Engine - removal leaving manual gearbox in vehicle . . . . . . . . . . . . . .5
Engine - removal leaving automatic transmission in vehicle . . . . . . . .6
Engine mountings - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Flywheel/driveplate - removal, inspection and refitting . . . . . . . . . . .22
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Initial start-up after overhaul or major repair . . . . . . . . . . . . . . . . . . .32
Major operations possible with the engine in the vehicle . . . . . . . . . . .3
Major operations requiring engine removal . . . . . . . . . . . . . . . . . . . . .4
Oil pump drive chain and sprockets - examination and renovation . .28
Oil pump - dismantling, inspection and reassembly . . . . . . . . . . . . .27
Oil pump - removal and refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Pistons and connecting rods - removal and refitting . . . . . . . . . . . . .29
Sump - removal and refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Timing chain and sprockets - removal and refitting . . . . . . . . . . . . . .15
Timing chain, sprockets and tensioner - examination and renovation .16
2B•1
Specifications Contents
2B
Unless otherwise stated, procedures are as described for the SOHC engines in Part A of this Chapter.
Easy,suitable for
novice with little
experienceFairly easy,suitable
for beginner with
some experienceFairly difficult,
suitable for competent
DIY mechanic
Difficult,suitable for
experienced DIY
mechanicVery difficult,
suitable for expert
DIY or professional
Degrees of difficulty

6Before removing the crankshaft, check that
the endfloat is within the specified limits by
inserting a feeler blade between the centre
crankshaft web and one of the thrustwashers
(the thrustwashers are fitted to the crankcase,
not the bearing cap). This will indicate whether
or not new thrustwashers are required.
7Unscrew the bolts, and tap off the main
bearing caps complete with bearing shells.
8Lift the crankshaft from the cylinder block,
and remove the rear oil seal if it is still in place
on the crankshaft.
9Extract the bearing shells, and recover the
thrustwashers, keeping them identified for
location.
Refitting
10Commence refitting as follows(see
illustration).
11Wipe the bearing shell locations in the
crankcase, and the crankshaft journals with a
soft non-fluffy rag.
12If the old main bearing shells are to be
renewed (not to do so is a false economy,
unless they are virtually new) fit the five upper
halves of the main bearing shells to their
locations in the crankcase.
13Fit the thrustwashers to the centre main
bearing location, using a little grease to retain
them if necessary. The oil grooves in the
thrustwashers must face outwards (ie facing
the crankshaft webs). Note that where
standard thrustwashers have been fitted in
production, the centre main bearing is
unmarked. If oversize (0.38 mm)
thrustwashers have been fitted, the centre
main bearing will carry a yellow paint mark.
14Lubricate the crankshaft journals and the
upper and lower main bearing shells with
clean engine oil, then carefully lower the
crankshaft into the crankcase.
15Lubricate the crankshaft main bearing
journals again, and then fit the main bearing
caps in their correct locations, with the arrows
on the caps pointing to the front of the engine.16Fit the main bearing cap bolts, noting that
the studded bolts secure bearing caps Nos 3
and 5.
17Lightly tighten all the securing bolts, then
progressively tighten all bolts to the specified
torque.
18Check that the crankshaft rotates freely.
Some stiffness is to be expected with new
components, but there must be no tight spots
or binding.
19Check that the crankshaft endfloat is
within the specified limits by inserting a feeler
blade between the centre crankshaft web and
the thrustwashers.
20Refit the sump mounting plate to the front
of the cylinder block, and tighten the securing
bolts to the specified torque.
21Carefully wind a thin layer of tape around
the rear edge of the crankshaft, to protect the
oil seal lips as the rear oil seal is installed.
22Refit the crankshaft rear oil seal housing,
using a new gasket, and tighten the securing
bolts to the specified torque.
23Ideally, the new oil seal should be
installed using a tool similar to that used for
fitting the crankshaft rear oil seal. A suitable
tool can be improvised using a metal tube of
suitable diameter, a metal disc or flat bar, and
two flywheel bolts. Draw the seal into position
using the two flywheel bolts. Make sure that
the seal lip faces into the engine.
24With the oil seal installed, carefully pull the
tape from the edge of the crankshaft.
25Refit the pistons and connecting rods.
26Refit the flywheel/driveplate, and the
timing chain and crankshaft sprocket.1Proceed as described in Chapter 2, PartA,
noting the following.
2Production bearing undersizes are
indicated as follows:
Yellow or red paint marks on crankshaft -
standard-diameter main bearing journals.
Green line on crankshaft front counterweight
- main bearing journals 0.25 mm
undersize.
Green spot on counterweight - big-end
bearing journals 25 mm undersize.
1Refer to Chapter 2, PartA, but note that
when the engine is first started, a metallic
tapping noise may be heard. This is due to the
timing chain tensioner plunger assembly
taking time to pressurise with oil, resulting in a
temporarily slack chain. The noise should
stop after a short time, once oil pressure has
built up.
32Initial start-up after overhaul or
major repair
31Crankshaft and bearings -
examination and renovation
2B•18DOHC engine
30.5 Main bearing cap identification mark
(arrowed)
30.10 Crankshaft main bearings and associated components
1 Bearing cap
2 Thrustwasher
3 Stud for oil baffle4 Identification markings
5 Bearing shell without oil
groove6 Bearing shell with oil
groove
7 Bearing seat in cylinder
block