maintenance FORD SIERRA 1992 2.G XR4 Workshop Manual

pA Constant Velocity Joints & Boots The Merkur XR4Ti and Scorpio
independent rear axle assemblys utilize half shafts that have inner and outer constant
velocity joints. Eventually these joints and protective boots will require service. We
have joints and boots available separately making it economical to replace just the
worn component without having to replace whole axle assembly. However, if more
than one C.V. per axle requires service, our complete axle assembly is the more cost
effictive way to go.
Note: right/left inboard and outboard C.V. joints and boots are
interchangeable- see price list for complete axle prices (handed left & right)
Constant Velocity Joint- XR4 & ScorpioM550B
C.V. Boot Kit-
XR4 & ScorpioM550BK
Complete Axle(specify left or right)-
XR4 & ScorpioM550L/R
pB
Rubber Drive Shaft Coupling The rubber "Drive Donut" or "Rotoflex
Coupling" on the XR4 and Scorpio drive shaft can be a real bugger. Many owners
have contacted us after being quoted up to 500.00 to totally replace the complete
drive shaft assembly by the local Ford L/M dealer, as they do NOT list the rubber
drive coupling as a separate service part. We import the proper replacement
drive coupling and make it available at considerable savings to you. If your car
exhibits a driveline shudder that increases with speed, (especially noticeable in
colder weather) we recommend taking a close look at the condition of the drive
coupling. Cracks in the rubber or missing pieces will require immediate replace-
ment, loosing one of these joints at speed will be very messy !
Note: BAT supplies
the standard equipment XR4i drive coupling by the original supplier to Ford. This
is not a lesser "fits all" component that just happens to be similar.
Rubber Drive Shaft Coupling- XR4 & ScorpioM17A
pC
Drive Shaft Center Support Bearing- Replacement driveshaft
center support bearing assemblys for XR4Ti and Scorpio.
Drive Shaft Center Support Bearing- XR4Ti M550SB
Drive Shaft Center Support Bearing- Scorpio G550SB
pD
Quaife Torque Biasing Differential Quaife torque biasing
differentials provide a constant and infinitely variable output to both rear
wheels. These unique differentials utilize a series of helical gears which
sense the amount of applied torque and adjust automatically for loss of
traction. The Quaife limited slip design is also free of high wear items
(clutches, ratchets and plates), making them stronger and more maintenance
free than other types of limited slip units. Anyone who has had the pleasure
of driving a vehicle equipped with a Quaife LSD will immediately comment on
its smooth seamless performance, very unlike clutch/plate type LSD's which
exhibit a notchy ratchet like take up through the drive line. The Quaife LSD
that we offer is originally designed as a replacement upgrade for the Sierra
Cosworth and are now supplied with output flanges tapped for either the large
108mm (Cosworth size) or smaller 100mm (XR4 size) C.V. joints.
Quaife Limited Slip DifferentialM710
pE
Clutch Kits We have a very good selection of clutch packages that include
clutch disk, pressure plate, throw out bearing, and clutch alignment tools. Buying one
of our engineered kits will guarantee best quality, performance, fitment (ease of
installation) and price. First option is a new (not rebuilt or re-lined) O.E. quality
replacement clutch kit by Sachs/Valeo. This clutch is best suited for standard or
slightly modified cars being used under normal driving conditions. If your requirements
are beyond the capabilities of the standard clutch we also have some heavy duty clutch
kit options. H.D. clutch kits include pressure plates that have increased clamping force
(from 30 to 50%) and clutch disks with high temperature friction materials applied.
Centerforce H.D. clutch kits have a unique centrifugal pressure plate design with
substantially more clamping force but requires very little pedal pressure over the stock
clutch.
Note: all kits are for standard transmission 1" 23 spline except where noted.
Sachs Clutch Kit XR - best quality O.E. clutchM519K
Sachs Clutch Kit Scorpio -
best quality O.E. clutchG519K
Sachs Clutch Kit XR w/ T5 Trans -
1 1/16" 10 spline for T-5 transM519T5
H.D. Centerforce Clutch Kit -
uprated disk & 30% p. plateM519C
H.D. Center Force II Clutch Kit -
uprated disk & 50% p. plateM519C2
Clutch Alignment Tool -
1" 23 spline for std. transmissionS11H
Clutch Cable- XR4Ti M562
Clutch Cable- Scorpio G562pD
Driveline
pA
pD pB
pC
1 1

L4-218
L2G L4ES
L15D
L15DS
L604A
L15E
L2KS L4FS
2300 Turbo Engine Components
Cylinder Block Bare (H.D. "Turbo" Block) L2G 475.00
Main Cap Stud Set (H.D. ARP) L2KS 94.55
Full Gasket Set (Felpro)
1985 engineL15AA 95.00
Full Gasket Set (Felpro)
1986-89 engineL15AB 124.50
Top End Gasket Set (Felpro)
specify year when orderingL15BA 55.00
Top End Gasket Set (Felpro)
with hi-temp valve cover setL15BB 79.50
Bottom End Gasket Set (Felpro)
1985 engine (cork pan)L15CA 40.10
Bottom End Gasket Set (Felpro)
1986-89 engine (rubber pan)L15CB 73.85
Oil Pan Gasket (1 piece rubber) 1986-89 L15CP 34.25
Head Gasket (Felpro) L15DA 19.50
Competition Head Gasket (Felpro #1035)
steel wire ring typeL15DF 59.50
Competition Head Gasket (extreme duty racing gasket) L15DR 29.50
Valve Cover Gasket- Cork L15E 6.79
Valve Cover Gasket H.D. (1 piece rubber) includes upper manifoldL15EA 24.00
Intake Manifold Gasket Set L15FA 11.40
Exhaust Manifold to Cylinder Head L15GA 7.50
Turbo Charger to Exhaust Manifold (stainless) L521GT 8.75
Water Outlet Gasket L15N CALL
Water Pump GasketL15P CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Oil Pump (standard)
MellingL2P 42.90
Oil Pump- (high pressure/ high volume) L2HP 73.20
Water Pump (new) L6A 73.10
Water Pump (recon) L6AA 39.00
Fuel Pump- Electric XR4Ti (in line) M10A 165.00
Fuel Pump- Electric XR4Ti (in tank) M10AT 125.00
Engine Components
Utilizing a design similar to the earlier German
2000 OHC "Pinto" engine the 2300 "Lima" en-
gine eventually replaced the 2000 OHC in most
North American Ford 4 cylinder vehicles from
1974 on. Built for lower maintenance with the
addition of hydraulic lash
adjusters the 2300
was designed to
operate in a lower
RPM range using
its larger displace-
ment and in-
creased torque to
its best advan-
tage. Perfor-
mance turbo-
charged versions
of the 2300 began
to appear in 1979 in
the Mustang/Capri and continued through the
80's in a more refined and powerfull EFI turbo
version. A reduced bore 2000 displacement
"Ranger" truck engine (from 1983-87) was also
produced. Some late production "Lima" engines
are equipped with hydraulic roller cam and valve
train, and other versions use dual spark plug
cylinder heads. The 2300 is a fairly rugged
engine in its stock form, however some compo-
nents will require up-rating with performance
components if high RPM duty is required. The
"Lima" series turbo and normally aspirated en-
gines respond quite well with a bit of perfor-
mance tuning and though lacking in refinement
do give quite a bit of bang for the buck.
Main Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16A 32.65
Connecting Rod Set- (4) Forged H-beam 5.20" length L4ES 549.00
Connecting Rod Set- (4) Forged
I-beam 5.20" length L4ESB 398.00
Connecting Rod Set- (4) Forged H-beam 5.70" length L4ESA 549.00
Rod Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16H 16.35
Con Rod Bolt Set- ARP H.D. (for standard 2.3L rod) L4FS 47.70
Head Stud Set- ARP H.D. L2DS 105.00
Cam Bearing Set- ACL/Vandervell L16M 18.50
Cam Bearing Set- ACL/Vandervell (360 degree O.D. groove) L16MA 18.50
Aux. Shaft Bearing L5DC 20.25
Cam Follower- (standard O.E. type)
eachL5B 7.50
Cam Follower- (roller type)
eachL5BR 16.00
Ring Set- Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4R 85.90
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4TF 98.00
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .025", .035", .045", .065")

*for above "performance pistons" - file fit top ringL4T1 127.50
Ring Set*- Gapless Moly type 2mm, 2mm, 4.75mm (std, .020", .030", .040", .060")
*for standard OE type pistons - specify sizeL4TFA 98.00
Performance Piston- Power Forged #250F (std, +.020", +.030", +.040", +.060 sizes)
exact replacement for standard 2.3 turbo piston, light weight "power forged"
design, 1.589" comperssion height for 8.0:1 compression, 2mm 2mm 4.75mm
ring land, supplied with wrist pins and locks.
L4-250F 62.20
Performance Piston- Forged (custom)
BAT can supply custom forged pistons to your specifications. Information regarding
bore size, ring land sizes & locations, compression height, and wrist pin bore size
is required for ordering. Pricing is on request
2 8