oil pressure FORD SIERRA 1992 2.G XR4 Workshop Manual

pC pB
pD pJ
pK
pE
pJ
pG
pI
pF
pH
Suspension - (front)0 2
pA
sway bar bushings
(see page 4)
pF Front Control Arms higher mileage cars exhibiting ball
joint and bushing wear can benefit from our standard control
arms. These arms are brand new, and include ball joints and
bushings installed.
Note: the outboard (sway/control arm) bushing
is an uprated "castellated" design which transmits less vibration
than the original U.S. spec. bushing.
(left) M428L
(right) M428R
pG
Inner Control Arm Bushing H.D. Made from
increased durometer rubber, these heavy duty (GPN) bushings
offer the desired firming effect while retaining a reasonable
degree of shock and vibration absorption. (each) M428BH-N
Optional urethane version of above bushing(set) M428BU
pH
Control Arm/Sway Bar Bushing Kit This heavy
duty urethane bushing set really does an excellent job
limiting the amount of "jutter" felt at the steering wheel
which is especially noticeable under braking. The kit includes
bushing halves and center sleeves to do both sides of the
car and is easy to install.
(set) M428BK
pH
Control Arm/Sway Bar Bushings As an option to
urethane bushings we offer either the "castellated" type
outer TCA bushings are available in standard rubber, or the
new style (better fills the void between the bushing halves)
H.D. GPN bushing kit. Both will dramatically reduce the
vibration under braking common to XR's and Scorpio's.
Outer TCA Bushings Standard (pair) does 1 armM428B
Outer TCA Bushing Set H.D. (set)M428BK-N
pI
Sway Bar Washer Get the most from your new
"castellated" type outer TCA bushings by using this "shallow"
washer (in front behind the lock nut) for a tighter fit.M407W
pJ
Tie Rod Ends High quality European Ford standard
replacement tie rod ends. (left) M434L (right) M434R
pK
Front Strut Upper Insulator H.D. Made from increased
durometer rubber, these heavy duty (GPN) Insulators offer the
desired firming effect while retaining a reasonable degree of
shock and vibration absorption. Steering and transitional
response becomes noticeably more direct.(each) M404 pA
Front Sway Bar The larger Cosworth Sierra 28.5mm
factory front sway bar is a direct replacement for the standard
25mm bar.
(H.D. bar clamp bushings are included)M407
NOTE: see price list for sway bar clamp bushings for XR & Scorpio
pB Spring Sets see page 3 (spring section) for listings
pC Front Struts (see below- shocks sold as each)
Spax TA series struts utilize a non pressurized gas over oil design
with 10 positive settings (knob type external adjustment on top) for
tuning the dampening to suit individual applications.M401A
Spax Sport One of the most popular shocks we sell, Spax fixed rate
gas sport shocks are an excellent choice for upgrading the handling
performance on the XR. M401V
Bilstein New for 2000. Bilstein's new sprint series gas shocks
offer the big B's renowned German made performance at a very
attractive price. Bilstein shocks are now available in our
suspension kits see page 3 for details.M401B
Rally/Sport Super-Gas made to European Ford spec. by Koni of
Holland. R/S shocks feature Konis twin-tube low pressure design and
have adjustable settings (knob type external adjustment on top) which
can be tailored to suit individual applications.
M401RS
Boge Turbo-Gas German manufactured twin tube high pressure
gas design utilizing a unique variable valving system that insures
the perfect balance between ride comfort and road holding
capability.M401S
DeCarbon French made mono tube high pressure gas shocks with
fairly sporty valving, similar in design to Bilstein.M401G
KYB GR2 gas struts are high quality, heavy duty units that are
a cost effective performance upgrade for the XR4. Handling is
improved without sacrificing ride quality.M401Y
pD
Steering Rack complete rack assembly w/inner tie rods,
boots, and stainless steel inner sleeve. M434SR
pE
Rack Boot* replacement steering rack boot M434RB
*same boot left or right XR4 & Scorpio
Shock Absorbers
GAS SHOCK ABSORBERSSUPER
GAS SHOCK ABSORBERScheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items

pA
pC
pDpG
pH
pE
pI
pF
GAS SHOCK ABSORBERS
pA Rear Sway Bar The larger Cosworth Sierra 16mm rear
sway bar is a direct replacement for standard U.S. spec. rear
bar.
(bar includes urethane bar clamp bushings)M408
Cosworth Bar 18mm w/bush for Scorpio G408
Rear Sway Bar Shackle Worn sway bar end link shackles
can reduce the rollbars effectiveness and should be
inspected and replaced if needed. (each)M408S
Rear Sway Bar Shackle for Scorpio G408S
pB
Rear Bar Bushings H.D. urethane bushings for either
standard 12mm or Cosworth 16mm bars. (sold each)
(12mm size) M408BU (16mm size) M408BAU
pC Spring Sets See page 3 for spring selection.
pD Rear Wishbone Set H.D. Race prepared rear arms are
fully strengthened with bracing tubes and capped to give a smooth
lower surface. The shock absorber mounts are gusseted for added
reliability. Inner and outer bushings are replaced with race quality
spherical bearings. Wishbones are supplied in a durable shot
blasted, powder coated finish.
M424
pE
Outer Rear Arm Bushing H.D. Made from specalized
aircraft urethane, these heavy duty bushings offer the desired
firming effect while retaining a reasonable degree of shock and
vibration absorption. (each-
2 halves w/sleeve) M424BO
pF
Body Beam Mount Bushing H.D. This heavy duty
rubber (GP N) bushing/mounts will reduce the for/aft movement
at the rear axle beam mounting points and really does a great job
in firming up the rear end. (each)M429B
optional urethane version of above bushingM429BU
note M429BU is specially designed for easy installation
pG Inner Rear Arm Bushing H.D. Made from specalized
aircraft urethane, these heavy duty bushings offer the desired
firming effect while retaining a reasonable degree of shock and
vibration absorption. (each-
2 halves w/sleeve) M424BI
Shock Absorbers
GAS SHOCK ABSORBERSSUPERpB
Differential Mount
See Page 32
pH Complete Beam Assembly H.D. Fully race
prepared beam/subframe assembly has capped and
braced tubes and double skinned wishbone and
differential mounting plates, supplied in a durable shot
blasted, powder coated finish.M429
pI
Rear Shock Absorbers (see below - sold as each)
Spax TA series shocks utilize a non pressurized gas over oil
design with external adjustment valve (external screw in bottom)
for fine tuning the dampening to suit individual applications.
Spax is England's largest and best known manufacturer of
performance shock absorbers.M402A
Spax Sport One of the most popular shocks we sell, Spax fixed
rate gas sport shocks are an excellent choice for upgrading the
handling performance on the XR.M402V
Bilstein New for 2000. Bilstein's new sprint series gas shocks
offer the big B's renowned German made performance at a
very attractive price. Bilstein shocks are now available in our
suspension kits see page 3 for details.M402B
Rally Sport Super-Gas made to European Ford spec. by Koni
of Holland. R/S shocks feature mono-tube high pressure design and
have 4 adjustable rebound (STD., +20%, +50%, +100%) settings
which can be tailored to suit individual applications.
M402RS
Boge Turbo-Gas shocks are a German manufactured twin
tube high pressure gas design utilizing a unique variable
valving system that insures the perfect balance between
ride comfort and road holding capability.M402S
DeCarbon French made mono tube high pressure gas shocks
with fairly sporty valving, similar in design to Bilstein. M402G
KYB Gas-Adjust shocks are well made, heavy duty
dampeners that are the least expensive performance shock
upgrade for the XR4. Handling is improved without
sacrificing ride quality.M402Y
NEW
0 6Suspension (rear)
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items

Turbocharger
pC
pG/H/I
pF
pD
pA
pB
pE
pA Standard Wastegate Actuator Since the stock XR
wastegate is no longer available new, we supply a high quality
re manufactured unit. Internal components (diaphragm) are re-
placed and exterior is zinc plated.) M521WR
pB
Turbochargers We offer both re manufactured stock
specification and modified high performance turbos for the
XR. High quality re manufactured turbos include; new center
cartridge compressor/turbine wheel assembly with recondi-
tioned outer compressor/turbine housings, new bearings,
seals and O-rings and fasteners. Our high performance turbo
adds a few extra tweeks. A GNX compressor wheel machined
into the stock comp housing for an additional 30% airflow and
a 360 degree thrust bearing is fitted for added durability.
Turbos are fully dressed and include wastegate actuator,
base & drain gaskets and sold on a exchange "core" basis-
outright purchase will add an additional $100.00 to the cost.
Standard Reman. Turbocharger M522TR
High Performance Turbocharger M522TM
pC
Intercooler Kit If you are looking for a large high flow
intercooler kit this is the one to have. Intercooler core mounts
ahead of the steering rack in front of the engine facing the
ground. Air is ducted up and through the core. Plumbing is kept
short and allows for a larger core than what can usually be fitted
in the bumper/grille area. Kit is complete with intercooler core
(8" x 20" x 3.5"), mounting brackets, inlet plumbing pipes &
connectors, clamps, turbo output elbow, bypass valve and
additional hardware and instructions.
M522ICpD
Adjustable Boost Valve Kit Replace the troublesome
stock boost control solenoid with this easy to adjust under hood
boost valve. This kit uses a check valve to accurately control the
boost level which allows for faster turbo spool-up (reduced lag)
over typical adjustable "bleed-off" valves. This is a low cost modifi-
cation and should be a "must have" for all XR's.
M521BV
pE
Dual Port Wastegate Actuator These are new actua-
tors which feature an adjustable length rod (set boost & pre load)
and dual vacuum ports. The dual port feature permits use of a
remote mounted boost valve (see below), but can also be used
as a replacement for stock actuator.
M521WA2
pF
Cockpit Mounted Boost Valve Remote cockpit
mounted adjustable boost valve for use with dual port wastegate
actuators (see above). Vacuum signal is regulated by the in
car mounted valve and recirculated to the dual port actuator for
precise adjustment. M521TB
pG
Turbo Oil Feed Pipe is prone to cracking/leaking and
should always be replaced when a new turbo is fitted to assure
proper oil flow. Just look inside an old one and you will see
what we mean. M522P
pH
Turbo Inlet Hose we have a version of this (discontin-
ued by Ford) hose that links the turbo outlet pipe to the throttle
body. Ours is high specification 4-ply Silicone (blue) rated to
over 600 degrees, 190 psi burst pressure- better & cheaper
than the original ! M22H
pI
Stainless Base Gasket replacement for between the turbo
base and exhaust manifold. L521GT
2 5

L4-218
L2G L4ES
L15D
L15DS
L604A
L15E
L2KS L4FS
2300 Turbo Engine Components
Cylinder Block Bare (H.D. "Turbo" Block) L2G 475.00
Main Cap Stud Set (H.D. ARP) L2KS 94.55
Full Gasket Set (Felpro)
1985 engineL15AA 95.00
Full Gasket Set (Felpro)
1986-89 engineL15AB 124.50
Top End Gasket Set (Felpro)
specify year when orderingL15BA 55.00
Top End Gasket Set (Felpro)
with hi-temp valve cover setL15BB 79.50
Bottom End Gasket Set (Felpro)
1985 engine (cork pan)L15CA 40.10
Bottom End Gasket Set (Felpro)
1986-89 engine (rubber pan)L15CB 73.85
Oil Pan Gasket (1 piece rubber) 1986-89 L15CP 34.25
Head Gasket (Felpro) L15DA 19.50
Competition Head Gasket (Felpro #1035)
steel wire ring typeL15DF 59.50
Competition Head Gasket (extreme duty racing gasket) L15DR 29.50
Valve Cover Gasket- Cork L15E 6.79
Valve Cover Gasket H.D. (1 piece rubber) includes upper manifoldL15EA 24.00
Intake Manifold Gasket Set L15FA 11.40
Exhaust Manifold to Cylinder Head L15GA 7.50
Turbo Charger to Exhaust Manifold (stainless) L521GT 8.75
Water Outlet Gasket L15N CALL
Water Pump GasketL15P CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Oil Pump (standard)
MellingL2P 42.90
Oil Pump- (high pressure/ high volume) L2HP 73.20
Water Pump (new) L6A 73.10
Water Pump (recon) L6AA 39.00
Fuel Pump- Electric XR4Ti (in line) M10A 165.00
Fuel Pump- Electric XR4Ti (in tank) M10AT 125.00
Engine Components
Utilizing a design similar to the earlier German
2000 OHC "Pinto" engine the 2300 "Lima" en-
gine eventually replaced the 2000 OHC in most
North American Ford 4 cylinder vehicles from
1974 on. Built for lower maintenance with the
addition of hydraulic lash
adjusters the 2300
was designed to
operate in a lower
RPM range using
its larger displace-
ment and in-
creased torque to
its best advan-
tage. Perfor-
mance turbo-
charged versions
of the 2300 began
to appear in 1979 in
the Mustang/Capri and continued through the
80's in a more refined and powerfull EFI turbo
version. A reduced bore 2000 displacement
"Ranger" truck engine (from 1983-87) was also
produced. Some late production "Lima" engines
are equipped with hydraulic roller cam and valve
train, and other versions use dual spark plug
cylinder heads. The 2300 is a fairly rugged
engine in its stock form, however some compo-
nents will require up-rating with performance
components if high RPM duty is required. The
"Lima" series turbo and normally aspirated en-
gines respond quite well with a bit of perfor-
mance tuning and though lacking in refinement
do give quite a bit of bang for the buck.
Main Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16A 32.65
Connecting Rod Set- (4) Forged H-beam 5.20" length L4ES 549.00
Connecting Rod Set- (4) Forged
I-beam 5.20" length L4ESB 398.00
Connecting Rod Set- (4) Forged H-beam 5.70" length L4ESA 549.00
Rod Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16H 16.35
Con Rod Bolt Set- ARP H.D. (for standard 2.3L rod) L4FS 47.70
Head Stud Set- ARP H.D. L2DS 105.00
Cam Bearing Set- ACL/Vandervell L16M 18.50
Cam Bearing Set- ACL/Vandervell (360 degree O.D. groove) L16MA 18.50
Aux. Shaft Bearing L5DC 20.25
Cam Follower- (standard O.E. type)
eachL5B 7.50
Cam Follower- (roller type)
eachL5BR 16.00
Ring Set- Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4R 85.90
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4TF 98.00
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .025", .035", .045", .065")

*for above "performance pistons" - file fit top ringL4T1 127.50
Ring Set*- Gapless Moly type 2mm, 2mm, 4.75mm (std, .020", .030", .040", .060")
*for standard OE type pistons - specify sizeL4TFA 98.00
Performance Piston- Power Forged #250F (std, +.020", +.030", +.040", +.060 sizes)
exact replacement for standard 2.3 turbo piston, light weight "power forged"
design, 1.589" comperssion height for 8.0:1 compression, 2mm 2mm 4.75mm
ring land, supplied with wrist pins and locks.
L4-250F 62.20
Performance Piston- Forged (custom)
BAT can supply custom forged pistons to your specifications. Information regarding
bore size, ring land sizes & locations, compression height, and wrist pin bore size
is required for ordering. Pricing is on request
2 8

Engine Components
Camshafts- see chart below
Hydraulic Lash Adjuster Set- (standard O.E. type) L5BA 43.00
Hydraulic Lash Adjuster Set- (high rev. anti pump-up) L5BH 49.95
Intake Valve- (standard O.E. type) L3H 8.25
Intake Valve- 1.740" (oversized stainless steel hi-flow)
eachL3HA 13.25
Intake Valve- 1.890" (oversized stainless steel hi-flow)
eachL3HB 15.00
Exhaust Valve- (standard O.E. type)
eachL31 25.75
Exhaust Valve- 1.510" (oversized stainless steel hi-flow)
eachL31A 13.25
Exhaust Valve- 1.590" (oversized stainless steel hi-flow)
eachL31B 15.00
Valve Spring Retainers (various)-
call with specific application------CALL
Valve Spring Set- (sport spring set for hydro cams to .480" lift) L3F 73.75
Valve Springs Racing-
call with specific application------CALL
Electric Fan Switch -XRM450FS 24.50
Knock Sensor-XRM450KS 52.70
Engine Coolant Temp Sensor (ECT)-XR M450EC 28.45
Idle Speed (Air Bypass Valve) XR/Scorpio
M450IS 79.90
Throttle Position Sensor (TPS)-XR M450TP 47.60
Oxygen Sensor (OS)-XRM450OS 60.50
Oil Pressure Switch-XRM450P 6.40
Water Temp Gauge Sender- XR (purple band)M450F 39.75
Adjustable Cam Sprocket (key way type) L5F 34.95
Adjustable Cam Sprocket (vernier type) L5FA 95.75
Cam Belt- (H.D. Ford Motorsport) L5G 29.95
Cam Belt- (H.D. Pirelli type)L5GA 15.00
Fuel Injector 2.3L Turbo (35pph -disk type) each L7G 68.50
Fuel Injector 2.3L Turbo- Remanufactured (35pph -brown top) each M7G 49.50
Intake Hose- Turbo Outlet to Throttle Body (Hi-Temp 4-Ply Silicone "Blue") XR4Ti, T-Bird & SVO M22H 47.00
Air Vane Meter* 50mm (T-Bird)
reconditionedL7V 164.50
Air Vane Meter* 65mm (SVO)
reconditionedL7VA 175.00
*can also be used for performance upgrade on XR4Ti with "PE" programed chip (call for information)
Distributor- 2.3L Turbo (reman) w/o cap, rotor, module (35.00 core) L9AB 119.00
Distributor Cap H.D. (hi-temp epoxy w/brass terminals) L9B 16.98
Distributor Rotor H.D. (hi-temp epoxy)
85-86 screw down typeL9F 7.50
Distributor Rotor H.D. (hi-temp epoxy)
87-89 push-on typeL9FA 8.90
Ignition Module TFI (on distributor) L9M 80.75
Ignition Wire Set- (8mm custom length w/silicone jacket and boots)L9HT 39.00
Ignition Wire Set- (8.5mm custom length w/silicone jacket and boots) M9HT69.50
Ignition Wire Set- (10mm custom length w/silicone jacket and boots)M9HTR 79.50
Performance Air Filter KN (2.3L Turbo) XR4Ti M22P 32.50
*durations quoted gross & .050" - timing events are @.050"
Grind#
Pricing $DescriptionPower
BandCam Lift
inlet/exhst.Valve Lift
inlet/exhst.Duration
inlet/exhTim ing
FiguresTiming
Inlet @
Full LiftValve
Clearance
inlet/exhst.Com m ents
2300 Turbo Camshafts (Hydraulic)
H260
$169.00Hydraulic2500-6000.252"/.252".416"/.416"272/272
220/2200/40 40/01100 / 0smooth idle, strong low and mid performance,
turbo suitable, auto & manual trans.
H283
$169.00Hydraulic3500-6500.274"/.274".453"/.453"276/276
224/2242/42 42/21100 / 0good idle, strong low and mid performance,
turbo suitable, manual transmission only
2300 Turbo Camshafts (Hydraulic Roller*) *for cars origionally equipped or kit available below
HR220
$385.00Hydro-roller2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR225
$399.00Hydro-roller3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR310
$375.00Hydro-roller3000-7000.317"/.317".535"/.535"284/284
224/2240/44 44/01120 / 0H.P. roller cam for cars origionally equipped.
turbos use 112 centerline, manual transmission only
2300 Turbo Camshaft Kits (Hydraulic Roller)
HR220K
$680.00Hydro-roller
cam kit2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
HR225K
$715.00Hydro-roller
cam kit3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
2 9

Engine & Related Components
pADistributor Cap 2.3L Heavy duty epoxy/resin cap
w/brass terminals.L9B

pBDistributor Rotor 2.3L Heavy duty epoxy/resin rotor
(screw down type 1985-86).
L9F
pB
Distributor Rotor 2.3L Heavy duty epoxy/resin rotor
(push- on type 1987-89).
L9FA
pC
TFI Module 2.3L (Motorcraft)L9M
pD
Distributor 2.3L excludes cap, rotor, module
(35.00 core)
re manufacturedL9AB
pD
Distributor 2.9L excludes cap, rotor, module
(55.00 core)
remanufacturedG9AB
pE
Engine Management XR4Ti and Scorpio engine
management computers. (75.00 core)
remanufactured
XR4TI (specify auto or manual trans) M9C
Scorpio (specify auto or manual trans) G9C
2.3L Turbo Engine Sensors & Switches
pFElectric Fan Switch -XR M450FS
pGKnock Sensor-XR M450KS
pHEngine Coolant Temp Sensor (ECT)-XR M450EC
pIIdle Speed (Air Bypass Valve) XR/Scorpio
M450IS
pJThrottle Position Sensor (TPS)-XR M450TP
pKOxygen Sensor (OS)-XR M450OS
pLOil Pressure Switch-XR M450P
pM
Water Temp Gauge Sender- XR (purple band)M450F
Sensors & Switches (other)
Air Charge Temp. Sensor (ACT) Scorpio G450A
Coolant Temp. Sensor (ECT)- Scorpio M450EC
MAP Sensor -Scorpio G450M
Oil Pressure Switch- Scorpio G450P
Oxygen Sensor- Scorpio G450OS
Vehicle Speed Sensor- Scorpio G450S
Throttle Position Sensor- Scorpio G450TP
pCpB pA
pD
pN
pE
pNA/C Compressor XR4/Scorpio Nippondenso A/C
compressor units, includes clutch.
remanufacturedM470C
pO
Alternator Bosch (90 amp) alternators available for XR &
Scorpio. (10.00 core)
remanufactured.
Alternator -XR4TiM24A
Alternator -ScorpioG24A
pPStarter XR4Ti and Scorpio starter units. (30.00 core) re
manufactured.
Starter -XR4TiM23A
Starter -ScorpioG23A
pQFuel Injectors Replacement injectors for XR4Ti.
35 lb. Standard Brown Top Injector (reman) M7G
35 lb. Optional Disk Type Injector (new) L7G
pRVane Air Meter Larger 50mm (T-bird) and 65mm (SVO)
VAM's can be fitted as a performance upgrade on the XR4Ti.
("PE"
computer chip upgrade required)
50mm VAM (reman) L7V
65mm VAM (reman)L7VA
Standard VAM XR4Ti (reman)L7VM
pSFuel Pressure Regulator Standard replacement regulator
for XR4Ti.M7PR
pTElectric Fuel Pumps New XR4Ti (in line) high pressure
and (in tank) low pressure fuel pumps
Electric Fuel Pump (in line) high pressureM10A
Electric Fuel Pump (in tank) low pressureM10AT
Important note: all electrical items are pre-
tested before shipping. Carefully check all
wiring, fuses & relays
before ordering. Electrical
items are not returnable !
pF pGpHpI
pJ
pK
pL
pM
pO
pQpP
pS
pT
pR
3 1

Price List
PAGE 23 cooling system (Scorpio)
Hose- heater valve (out) to core G421HA 8.90
Hose- heater valve to engine G421HB 17.50
Hose- heater valve (inlet) to core G421HC 13.95
Hose- heater valve to pipe G421HD 18.75
Heater Control Valve- XR4 & Scorpio M421V 60.00
Hose- coolant pipe to oil cooler from heat valve G421HL 9.90
Oil Cooler- oil to water heat exchanger AD1000 110.00
Hose- oil cooler to coolant pipe G421HM 14.40
Hose- coolant pipe from oil cooler to water pump G421HK 17.90
Hose- bypass/ water pump outlet to inlet mfld. G421HP 14.10
Hose- upper radiator (late 89) w/vent G421TH-9 35.00
Hose- coolant tank to thermo housing G421HF-9 16.45
Tank Lever Sender M421LS 40.25
Lever Sender Install Kit M421SK 9.40
Cap/Plug- Rubber G421P 2.50
Hose- lower radiator (late 89) w/tee off hose G421BH-9 35.75
Coolant Tank (6/88>89) Oval TypeG421T 52.00
Coolant Tank (late style 6-88>2-92) rectangular shapeG421TL 46.00
Radiator Cap (thread-on) Scorpio & late XR4 G421C 7.35
PAGE 24 A/C system
Evaporator- (XR4 & Scorpio) M470E 245.75
Expansion Valve - (XR4 & Scorpio) M470EV 46.50
Blower Motor - (XR4)
O.E. FordM470A 198.00
Blower Motor - (Scorpio)
O.E. FordG470A 230.00
Refrigerant Hoses*- (XR4Ti only) M470H 149.00
Refrigerant Hoses*- (Scorpio) G470H 129.00
*this item requires an additional 100.00 charge refundable upon core return
Compressor- (XR4 & Scorpio) includes clutchM470C 429.00
Clutch Assembly*- (XR4 & Scorpio) M470CL 157.50
*this item requires an additional 25.00 charge refundable upon core return
Condenser- (XR4) M470D 335.00
Condenser- (Scorpio) G470D 335.00
Electric Condenser Fan- 16" Pusher (XR4 & Scorpio)A16F-PU 89.00
Fan Mounting Tie Set (for above fan)ABKT1 7.95
Pressure Switch-
(XR4 & Scorpio) O.E. Ford DISCONTINUED
Receiver/Dryer- (XR4 & Scorpio) M470R 108.00
Receiver/Dryer- (XR4 & Scorpio) O.E. Ford M470R-F 131.50
PAGE 25 turbo components
Wastegate Actuator* -Reman. M521WR 95.00
*this item requires an additional 30.00 charge refundable upon core return
Turbo/Reman* (specify auto or 5-speed) M522TR 425.00
Performance Turbo* M522TM 649.00
*this item requires an additional 100.00 charge refundable upon core return
Intercooler Kit M522IC 1195.00
Adjustable Boost Kit M521BV 48.00
Wastegate Actuator (adjustable rod- dual port) M521WA2 119.00
Cockpit Mount Adjustable Boost Kit (remote valve) M521TB 74.50
Turbo Oil Feed Pipe M522P 19.00
Turbo Inlet Hose (45 degree elbow) M22H 44.50
Turbo Base Gasket L521GT 8.75
02/05/023 9
PAGE 26 engine & related
Main Bearing Set (STD) L16A 32.65
Main Bearing Set (+.010") L16B10 32.65
Main Bearing Set (+.020") L16B20 32.65
Main Bearing Set (+.030") L16B30 32.65
Rod Bearing Set (STD) L16H 16.35
Rod Bearing Set (+.010") L16110 16.35
Rod Bearing Set (+.020") L16120 16.35
Rod Bearing Set (+.030") L16130 16.35
Cam Bearing Set L16M 18.50
Cam Bearing Set- grooved L16MA 18.50
Aux. Shaft Bearing L5DC 10.50
Connecting Rod Bolt Set H.D. (standard 2.3 rod) L4FS 44.30
Connecting Rod Bolt Set H.D. (5.7" Chevy rod) L4FSC 35.00
Head Stud Set H.D. L2DS 98.40
Main Stud Set H.D. L2KS 89.20
Full Gasket Set (complete engine) Felpro L15AA 95.00
Top End Gasket Set Felpro L15BA 55.50
Bottom End Gasket Set (block, crank & sump) Felpro L15CA 40.10
Pan Set- sump rails & seals (cork) L15CP 22.05
Head Gasket H.D. (Ford Motorsport turbo style) L15D 16.00
Head Gasket H.D.- Felpro L15DA 19.50
Head Gasket Competition (extreme duty racing gasket)L15DR 29.50
Head Space Shim .020" L15DS 17.85
Valve Cover Gasket (standard cork) L15E 6.75
Valve Cover Gasket H.D. 2300 (hi-temp rubber)L15EA 24.00
Valve Cover Gaskets H.D. 2.9L V6 (hi-temp rubber)G15EA 15.50
Intake Manifold Gasket Set L15FA 11.40
Water Outlet Gasket (thermostat housing) L15N CALL
Water Pump Gasket (pump to block) L15P CALL
Crankshaft Rear Seal L15Q CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Inlet Hose- Turbo to T.Body (silicone blue) M22H 45.00
Performance Exhaust System 3" (full system) M522 705.00
Performance Exhaust System 2.5" (down pipe w/cat back)M522B 425.00
Exhaust Down Pipe 3" M522DP 159.00
Exhaust Manifold (standard cast Fomoco) M521 185.00
Exhaust Header 2.3 Turbo (tubular stainless steel) L521T 595.00
Gasket- turbocharger to manifold (stainless) L521GT 8.75
Exhaust Hanger (rubber donut) each C522H 5.25
PAGE 27
engine & related
Air Filter- XR4Ti (2.3L Turbo) M22P 35.10
Air Filter- Scorpio (2.9L V-6) G22P 50.00
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot 320510 4.55
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot 320512 4.90
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot 320516 5.64
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot 320520 6.32
Motor Mount Insulator (left or right same) XR- each M433 99.50
Motor Mount Insulator (L or R same) Scorpio- each G433 69.45
Transmission Mount/Insulator- Scorpio G433T 39.50
Transmission Mount/Insulator H.D. M433TA 53.00
Trans Crossmember XR (wide) 87-89 manual & auto
DISCONTINUED
Trans Crossmember XR (narrow) 85-86 manual & autoDISCONTINUED
Belt- XR4Ti (1985-89) W. Pump, Alt, P. SteeringM6G 11.90
Belt- XR4Ti (1986-89)
A/C Comp.M6H 9.50
Belt- XR4Ti (1985)
A/C Comp.M6HA 9.50
Belt- Scorpio (1988-89)
Fan & Power SteeringG6G 14.20
Belt- Scorpio (1988-89)
AlternatorG6GA 12.65
Belt- Scorpio (1988-89)
A/C Comp.G6H 10.25
Ignition Wire Set- XR4Ti (8mm ) L9HT 39.95
Ignition Wire Set- XR4Ti (8.5mm KV85 wire) M9HT 69.50
Ignition Wire Set- XR4Ti (10mm R-100 wire) M9HTR 79.00
Ignition Wire Set- Scorpio (8mm) G9HT 50.75
Ignition Wire Set- Scorpio (8.5mm KV85 wire) G9HT9 88.75

Pages 28-30
Pricing is listed with part numbers on these pages
PAGE 31 engine & related
Distributor Cap H.D. 2.3L L9B 16.98
Distributor Rotor H.D. 2.3L (85-86 screw-down type) L9F 7.50
Distributor Rotor H.D. 2.3L (87-89 push-on type) L9FA 8.90
TFI Module 2.3L -Motorcraft XR & Scorpio L9M 80.75
Distributor* 2.3L L9AB 119.00
*this item requires an additional 35.00 charge refundable upon core return
Distributor* 2.9L V6G9AB110.25
*this item requires an additional 55.00 charge refundable upon core return
Computer* XR4Ti (specify auto or manual) M9C 143.50
Computer* Scorpio (specify auto or manual) G9C 143.50
*this item requires an additional 75.00 charge refundable upon core return
Electric Fan Switch -XR M450FS 24.50
Knock Sensor -XR M450KS 52.70
Engine Coolant Temp. Sensor (ECT) -XR & Scorpio M450EC 28.45
Idle Speed Sensor (Air Bypass Valve) -XR & Scorpio M450IS 79.90
Throttle Position Sensor (TPS) -XR (order with year) M450TP 47.60
Oxygen Sensor -XR M450OS 60.50
Oil Pressure Switch -XR M450P 6.40
Water Temp Gauge Sender (purple band) -XR M450F 39.75
Air Charge Temp Sensor (ACT)- Scorpio G450A 29.25
Coolant Temp. Sensor (ECT)- XR & Scorpio M450EC 28.45
MAP Sensor -Scorpio G450M 97.50
Oil Pressure Switch -Scorpio G450P 6.00
Oxygen Sensor -Scorpio G450OS 114.50
Vehicle Speed Sensor- Scorpio G450S 119.00
Throttle Position Sensor- Scorpio G450TP 153.00
A/C Compressor -XR & Scorpio M470C 449.00
Alternator* -XR M24A 235.00
Alternator *-Scorpio G24A 235.00
*this item requires an additional 10.00 charge refundable upon core return
Starter* -XR M23A 87.50
Starter* -Scorpio G23A 220.00
*this item requires an additional 30.00 charge refundable upon core return
Fuel Injector 35lb. XR4Ti (Brown Top) remanM7G 49.50
Fuel Injector 35lb. (Disk Type)
new DISCONTINUED
Vane Air Meter* 50mm (T-Bird) L7V 164.50
Vane Air Meter* 65mm (SVO) L7VA 175.00
Vane Air Meter* XR4Ti Standard L7VM 255.00
*this item requires an additional 75.00 charge refundable upon core return
Fuel Pressure Regulator -XR M7PR 52.35
Electric Fuel Pump- XR (high pressure) in line M10A 165.00
Electric Fuel Pump- XR (low pressure) in tank M10AT 125.00
PAGE 32 transmission related
Oil Seal- input shaft (front) T9 M703 9.30
Gasket- input bearing retainer to main case T9 M702G 2.05
Gasket- top cover T9 M716 6.75
Oil Seal- extension housing (tail shaft) T9 M719 11.80
Gasket- adaptor plate (bearing carrier) to main case T9 M709 4.95
Gasket- adaptor plate (carrier) to ext. housing (tail) T9 M708 6.80
Short Shift Kit M715 55.00
Shifter- competition gear lever (shifter) assembled M717 114.50
Torco Gear Oil (quart) C2S 10.25
Quadrant & Pawl Kit M368 18.90
Transmission T9 (remanufactured) M700 CALL
PAGE 33-34
Pricing is listed with part numbers on these pages
4 0 Price List03/27/02
NEW ITEMS.... Too Late To Classify
Valve Cover Gaskets H.D. 2.9L V6 (h.d. rubber)G15EA 15.50
Head Gasket 2.9L V6 (RH) G15DR 22.50
Head Gasket 2.9L V6 (LH) G15DL 22.50
Main Bearing Set 2.9L V6 (specify size) G16A 53.10
Rod Bearing Set 2.9L V6 (specify size) G16H 31.05
Weather Seal - Rear Hatch to Body -Scorpio G340HS 80.00
Electric Window Switch (door/console)- Scorpio G340S 31.10
Rear Sensor Wiring (low pad warning) Scorpio G420SWR 39.45
Vacuum Modulator- A4LD Auto Trans G750M 26.00
Shop Manual T9 Transmission M201 13.95
Weather Seal- Rear Hatch to Body- XR M340HS 79.90
Moulding/Seal Front Windshield-XR M340F 30.00
Weather Seal- Sunroof Opening- XRM340SR 71.00
Weather Strip- Sliding Sunroof Panel- XRM340SRP 24.25
Electric Window Switches (2) Console-XR M340S 47.30
Ignition Switch (Electrical)- XR M350A 41.75
Ignition Lock Cylinder & Keys- XR M350L 69.00
Plastic Rivet- for exterior body cladding- XR M366R .75
Wiper Link Arm (long) ties L & R arms- XR M369 14.35
Wiper Motor Link Arm (short) XR M369A 14.35
Front Sensor Wiring (low pad) XR & Scorpio M420SW 32.50
Bushing- Body Baem Mount Standard M429 36.00
PCV Valve- XR M450V 5.00
Rotary Fan Switch HVAC- XR M470FS 60.00
Rear Wheel Bearing Carrier- XR M550BC 96.25
Rear Stub Axle (LH) XR & Scorpio M550SL 129.00
Rear Stub Axle (RH) XR & Scorpio M550SR 129.00
Transmission Shift Rail Bushing (in case) M718 2.55
Transmission Shift Bushing (on shaft @ shifter) M715B 2.95
Vacuum Modulator- C3 Auto Trans M750M 26.00
(rear)
(center)
Scorpio Exhaust Components- Scorpio exhaust system
components are generally both expensive and difficult to have
reproduced by the local muffler shop. The center section with
all its close proximity twists and bends makes for some real
aggravation. BAT can supply original quality replacement
exhaust parts at very attractive pricing. Center sections are
one piece and include the main muffler, connecting from the
catalytic converter to rear resonator. Rear sections are standard
type rear (can) resonator.
Scorpio Center Muffler Section G522 $149.00
Scorpio Rear Resonator Section G522T $90.00
Exhaust Hanger (each) C522H 5.95
New