service FORD SIERRA 1992 2.G XR4 Workshop Manual

PERFORMANCE & SERVICE
PARTS GUIDE
Merkur XR4ti / Sierra XR4i / Sierra RS Cosworth / Sierra RS 500 / Merkur Scorpio
CATALOG 08/2002 EDITION
BAT BATBAT BAT
BAT Inc.
British American Transfer Inc.
7630 Matoaka Road
Sarasota, FL 34243
phone (941) 355-0005
fax (941) 355-4683
www.batinc.net

pA Front Caliper We offer high quality re-manufactured
front calipers which are considerably less costly than new.
Calipers are handed left & right and require return core charge.
(drivers- left) M420CL(passenger- right) M420CR
pB
Caliper Repair Kit -w/piston Ford caliper repair kits are
an economical way to service a leaking or "sticky" caliper. Fitting
this kit, after honing the piston bore, will cure most caliper related
problems. (kit does 1 caliper)M420K4A
pC
Caliper Seal Kit After inspection many calipers only
require new seals to put them right. (kit does 1 caliper) M420K4
pD
Performance Street Brake Pad Set Premium
Mintex A/F series brake pads will give enhanced brake perform
over a wide temperature range with very little brake dusting.
Mintex pads also incorporate the pad warning sensor wiring.
This is the abusolute best performing street pad we have tested
and for the price they are a steal.
(XR4 & Scorpio)M420M
pD
Racing Brake Pad Sets Mintex 1144 is a rally/race pad
that is perfectly at home on track or street, offering a high coefficient
of drag (.44) and excellent modulation throughout a very wide
operating range (up to 1200 degrees). Mintex 1144 is supplied pre-
burnished for easy break-in and minimal fade on the first heating
cycle. Both fade resistance and wear characteristics are excellent.
Mintex pads are the only racing brake pads to incorporate the
standard "low pad" sensor wiring. Match a set of these pads with our
drilled or grooved sport rotors and Aeroquip stainless brake lines for
a substantial increase in braking performance.
(XR4 & Scorpio)
Mintex Street/Competition (M1144)M420G
Mintex Full Competition (M1155) M420GA
pE Standard Front Rotors Lesser quality generic "white
box" rotors tend to warp easily, don't even consider fitting them
on your XR4 or Scorpio. BAT supplies only the highest quality
(Brembo -
Italy & United Brake -England) rotors at better than
"bargain" rotor prices. (each)
XR4 M425
Scorpio G425
pE
pC
pD
pD
pA
pB pF
Brake System (front)
pH
See price list for caliper
slide bushings and pins
pG
0 7
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
pF Cross Drilled Front Rotors Cross-drilling brake
rotors is an excellent way to increase brake performance.
Theory being that centrifugal force will draw excess brake
dust and expelled gasses from the pad surface through the
drilled passages into the rotors vented cavity and out. This
process also improves rotor cooling giving improved braking
response and resistance to fade. Our drilled brake rotors
are made from Carballoy (a medium flake graphite fully
pearlitic low phosphorous iron) manufactured to BS 1452
- 1990 grade 180/220 standard. The cross drilling process
is handled by computer CNC milling equipment with holes
arranged in a parabolic pattern giving an even sweeping
effect to the pad surface ensuring maximum cooling with
minimum noise and drag. M425CD
*rotors must by purchased as (handed) pairs- priced as each
Grooved Front Rotors As an option we can supply
slotted (grooved) pattern rotors which are manufactured to
the same high standards as the above listed cross drilled
versions.M425S
*rotors must by purchased as (handed) pairs- priced as each
Drilled & Slotted Front Rotors As an option we can
supply combination drilled & slotted (grooved) pattern
r o t o r s manufactured to the same high standards as the above
listed cross drilled versions.M425CDS
*rotors must by purchased as (handed) pairs- priced as each
pG Master Cylinder high quality Bendix replacement power
brake master cylinder.
(specify year when ordering)M420MC
pH
Aeroquip Brake Lines One of the more effective brake
modifications you can make is to replace the standard brake
hoses with Aeroquip steel braided lines. These performance
brake hoses incorporate a teflon interior to keep line expansion
"flexing" to a minimum. This greatly reduces the "spongy" pedal
feel common to the XR4 & Scorpio brake system. Our stainless
lines are assembled from genuine Aeroquip AN-3 hose with
premium metric "reusable" (not the lesser quality "swaged" type)
hose ends installed. XR4Ti (state year) M419
Scorpio G419

pA
pBpC
pEpD
pE Rear Brake Parts Kit This handy kit includes all of the
small parts, springs and other attaching hardware for the rear
drum brakes. One kit does both hand sides.M420K5
Rear Brake Special Our rear brake special has all the
items (brake shoes, wheel cylinders & small parts kit)
required for a complete rear brake overhaul, and all at a very
attractive price.M420RSPL
pF
Rear Disk Brake Kit Converting to rear disk brakes
could not be any easier than with our ventilated rear disk
conversion kit. Not only will braking performance be greatly
improved but servicing the friction material (pads) becomes a
much easier task than messing with the old shoes. Kit incudes:
calipers & mounting plates, vented 260mm rotors, brake lines,
hand brake cables, and assorted hardware.M420RK
Note: see price list for individual listings on service parts for
above rear disk brake kit.
XR4 & Scorpio Hand Brake Cables We have replacement
hand brake cable assemblies for both the XR4Ti and Scorpio.
These have been recently discontinued by Ford USA.
Hand Brake Cable XR4Ti M564
Handbrake Cable Scorpio G564
Cosworth Hand Brake Cable required for fitting a
Cosworth rear brake conversion to the XR4 or servicing cars
with existing Cosworth rear brake cables.Z16567
Scorpio Rear Brake Components BAT also stocks
brake components for servicing and upgrading the rear
brakes on the Merkur Scorpio.
Rear Rotor (standard) G425R
Rear Rotor (cross drilled) G425RCD
Rear Caliper (left or right) G420RL/RR
Rear Pad Set G420R pA
Rear Wheel Cylinder Backing plates should be checked
periodically for brake fluid drips or a damp spot at the bottom (a sure
sign of a leaky wheel cylinder). We recommend (and sell) only new
replacement wheel cylinders because of the high incidence of
failure found with re-manufactured units.M420WC
pB Rear Brake Shoes Our premium quality rear brake shoes
are supplied as either European Motorcraft or Mintex brand. Both
are new (non re-manufactured) high quality semi-metallic
replacement linings, not the typical "white box specials".
Note:
fitting reman rear shoes can be a problem as most we have seen
have thicker than standard bonded linings making it difficult, if not
impossible, to reinstall the drum.
M420R
pC
Rear Brake Drum Brake drums that are warped or
beyond minium specification for wear should be replaced.
New rear brake drums are sold each.M420RD
pC
Rear Brake Drum (Grooved) These rear drums offer
an extra degree of braking performance not found when
using standard rear drums. Drums have 12 spiral grooves
for maximum cooling and deglazing effect. Grooved drums
are sold in handed pairs.M420RDG
pD
Aeroquip Rear Brake Lines One of the more effective
brake modifications you can make to the XR4 & Scorpio is to
replace the standard brake hoses with Aeroquip steel braided lines.
These performance brake hoses incorporate a teflon interior to
keep line expansion "flexing" to a minimum. This greatly reduces
the "spongy" pedal feel common to most brake systems. Our
stainless lines are assembled from genuine Aeroquip AN-3 hose
with premium metric "reusable" (not the lesser quality "swaged"
type) hose ends installed.
XR4 Rear Aeroquip Brake Line Set M419R
Scorpio Rear Aeroquip Brake Line Set (4 lines)G419R
Brake System (rear)
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
pF
0 9

Brake (related)
pA
pEpA
Racing Brake Fluid Not all brake fluid is created equally. High
operating temperatures at the caliper transfers extreme heat through the piston
causing lesser quality brake fluid to boil. This in turn allows the fluid to become
compressed and reduces overall braking performance. The best way to
counter this from happening is to use a racing specification, mineral (never
synthetic) brake fluid and flush the system after each event for competition or
annually on performance street driven vehicles. Both AP550 and Wilwood 570
brake fluid is DOT approved with a dry boiling point of 550-570 degrees, low
viscosity minimizes aeration and permits easy bleeding.
Brake Fluid AP Competition (16.9oz. 500ml.) MC550
Brake Fluid Wilwood 570 (12oz. 355ml.) MC570
Brake Fluid Wilwood 570 (6 Pack) MC57-6
Brake Fluid Wilwood 570 (24 Case) MC57-C
pB
Cosworth & Scorpio Rotors For those fortunate few who own
Cosworth Sierras or have converted XR4's to Cosworth type front or rear brakes
and are in need of replacement rotors we have them. Scorpio front or rear rotors
in standard and cross drilled are also available. (see price list page 31)
Cosworth Front 283 x 24mm standard, X-drilled, grooved
Cosworth Rear 273 x 10mm standard, X-drilled, grooved
Scorpio Front 260 x 24mm standard or X-drilled
Scorpio Rear 253 x 10mm standard or X-drilled
Performance Brake Kits Engineered competition brake kits for the
ultimate in stopping power.
pC Front R/S Brake Kit (283 x 24mm)
BAT R/S "big brake" kit allows larger 11.25" (285mm) brake rotors to be fitted
with standard XR calipers. Increasing rotor "swept area" in this way will greatly
improve stopping power (leverage) and help to reduce high brake temperatures
that can cause premature brake fade and poor pedal feel.
Kit includes:
285 x 24mm vented (standard or cross-drilled) rotors, Mintex 1144 brake pad
set, caliper mounting brackets & hardware (fitment with most 15" wheels -
some require slight modification)
kit supplied with standard rotors
M418
kit supplied with cross drilled rotors M418A
pD Front Brake Kit (283 x 24mm) w/4 Piston Calipers
Combine the performance of the R/S large rotor kit with 4 piston calipers for the
ultimate in stopping power.
includes: 283 x 24mm vented rotors,
4-piston alloy Wilwood Superlite 2A calipers with pads. (fitment with most 15"
wheels -some require modification or spacers)
M416W
pD Front Brake Kit (300 x 32mm) w/4 Piston Calipers
For those who are looking for the ultimate brake performance. Quite simply the
largest and most competent competition type brake kit that can be fitted to the XR4.
includes: 300 x 32mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite IIA calipers, caliper mounting brackets & hardware
M417A
(this kit also available for Scorpio ! ) G417A
Rear Kit (XR4 w/16" wheels) 300 x 21mm (See Price List)
includes: 300 x 21mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite 2A calipers, caliper mounting brackets & hardware
pE Wheel Bearings Genuine European Ford wheel bearing kits are
complete with all required service parts to do a first class job. Each kit
include bearings, races, seals and hub nuts to service one wheel.
Front Wheel Bearing Kit (specify left or right) -XR4 M560F
Rear Wheel Bearing Kit (specify left or right) -XR4 M560R
Front Wheel Bearing Kit (specify left or right) -Scorpio G560F
Rear Wheel Bearing Kit (specify left or right) -Scorpio G560R
pB
pC
pD
1 0

pA Constant Velocity Joints & Boots The Merkur XR4Ti and Scorpio
independent rear axle assemblys utilize half shafts that have inner and outer constant
velocity joints. Eventually these joints and protective boots will require service. We
have joints and boots available separately making it economical to replace just the
worn component without having to replace whole axle assembly. However, if more
than one C.V. per axle requires service, our complete axle assembly is the more cost
effictive way to go.
Note: right/left inboard and outboard C.V. joints and boots are
interchangeable- see price list for complete axle prices (handed left & right)
Constant Velocity Joint- XR4 & ScorpioM550B
C.V. Boot Kit-
XR4 & ScorpioM550BK
Complete Axle(specify left or right)-
XR4 & ScorpioM550L/R
pB
Rubber Drive Shaft Coupling The rubber "Drive Donut" or "Rotoflex
Coupling" on the XR4 and Scorpio drive shaft can be a real bugger. Many owners
have contacted us after being quoted up to 500.00 to totally replace the complete
drive shaft assembly by the local Ford L/M dealer, as they do NOT list the rubber
drive coupling as a separate service part. We import the proper replacement
drive coupling and make it available at considerable savings to you. If your car
exhibits a driveline shudder that increases with speed, (especially noticeable in
colder weather) we recommend taking a close look at the condition of the drive
coupling. Cracks in the rubber or missing pieces will require immediate replace-
ment, loosing one of these joints at speed will be very messy !
Note: BAT supplies
the standard equipment XR4i drive coupling by the original supplier to Ford. This
is not a lesser "fits all" component that just happens to be similar.
Rubber Drive Shaft Coupling- XR4 & ScorpioM17A
pC
Drive Shaft Center Support Bearing- Replacement driveshaft
center support bearing assemblys for XR4Ti and Scorpio.
Drive Shaft Center Support Bearing- XR4Ti M550SB
Drive Shaft Center Support Bearing- Scorpio G550SB
pD
Quaife Torque Biasing Differential Quaife torque biasing
differentials provide a constant and infinitely variable output to both rear
wheels. These unique differentials utilize a series of helical gears which
sense the amount of applied torque and adjust automatically for loss of
traction. The Quaife limited slip design is also free of high wear items
(clutches, ratchets and plates), making them stronger and more maintenance
free than other types of limited slip units. Anyone who has had the pleasure
of driving a vehicle equipped with a Quaife LSD will immediately comment on
its smooth seamless performance, very unlike clutch/plate type LSD's which
exhibit a notchy ratchet like take up through the drive line. The Quaife LSD
that we offer is originally designed as a replacement upgrade for the Sierra
Cosworth and are now supplied with output flanges tapped for either the large
108mm (Cosworth size) or smaller 100mm (XR4 size) C.V. joints.
Quaife Limited Slip DifferentialM710
pE
Clutch Kits We have a very good selection of clutch packages that include
clutch disk, pressure plate, throw out bearing, and clutch alignment tools. Buying one
of our engineered kits will guarantee best quality, performance, fitment (ease of
installation) and price. First option is a new (not rebuilt or re-lined) O.E. quality
replacement clutch kit by Sachs/Valeo. This clutch is best suited for standard or
slightly modified cars being used under normal driving conditions. If your requirements
are beyond the capabilities of the standard clutch we also have some heavy duty clutch
kit options. H.D. clutch kits include pressure plates that have increased clamping force
(from 30 to 50%) and clutch disks with high temperature friction materials applied.
Centerforce H.D. clutch kits have a unique centrifugal pressure plate design with
substantially more clamping force but requires very little pedal pressure over the stock
clutch.
Note: all kits are for standard transmission 1" 23 spline except where noted.
Sachs Clutch Kit XR - best quality O.E. clutchM519K
Sachs Clutch Kit Scorpio -
best quality O.E. clutchG519K
Sachs Clutch Kit XR w/ T5 Trans -
1 1/16" 10 spline for T-5 transM519T5
H.D. Centerforce Clutch Kit -
uprated disk & 30% p. plateM519C
H.D. Center Force II Clutch Kit -
uprated disk & 50% p. plateM519C2
Clutch Alignment Tool -
1" 23 spline for std. transmissionS11H
Clutch Cable- XR4Ti M562
Clutch Cable- Scorpio G562pD
Driveline
pA
pD pB
pC
1 1

Engine Builders Kits
Time for that inevitable engine rebuild? BAT takes the guess work out of acquiring
all the right components by offering these prepackaged performance engine service
kits. Our top end (cylinder head) and bottom end (short block) rebuilding kits are
supplied complete with premium high performance parts. With the help of a competent
machine shop these rebuild kits will restore your engine to better than new condition.
As usual we have gone to great lengths to supply only the absolute best components
for the job and still managed to keep the prices reasonable.
Performance Short Block Rebuild Kit (2.3L Turbo)
(1) Full Gasket Set -Felpro L15AB
(1) Main Bearing Set -ACL Vandervell (specify size; STD, +.010", +.020", +.030") L16A
(1) Rod Bearing Set -ACL Vandervell (specify size; STD, +.010", +.020", +.030") L16H
(4) Forged Pistons -Power Forged (specify size; STD, +.010", +.020", +.030", +.040",
+.060")
L4250F
(1) Gapless Ring Set -Total Seal (specify size; STD, +.010", +.020", +.030", +.040",
+.060")
L4TF
(1) Rod Bolt & Nut Set H.D. -A.R.P. L4FS
(1) Oil Pump- Melling L2P
Short Block Rebuild Kit L501
$649.00
as above listed
Optional Items to Short Block Rebuild Kit
A) Forged Connecting Rod Set - "I" beam type w/ H.D. fasteners (add $350.00)
B) Forged Connecting Rod Set - "H" beam type w/ H.D. fasteners (add $525.00)
C) Main Stud Set H.D. - A.R.P. (add $75.00)
D) Crankshaft (if required) - resized, polished, balanced, indexed (add 349.00)
E) Crankshaft "Power Pulley" (add $90.00)
Performance Cylinder Head Rebuild Kit (2.3L Turbo)
(1) Top End Gasket Set* - Felpro L15BA * see notes below
(1) Cam Bearing Set -ACL Vandervell
L16M
(1) Head Bolt Set L2D
(4) Exhaust Valves -Stainless Hi-flow 1.51" L31A
(4) Inlet Valves -Stainless Hi-flow 1.74" L3HA
(1) Valve Spring Set H.D. L3F
(8) Cam Followers L5B
(1) Hydraulic Adjuster Set (lifters) L5B
(1) Cam Sprocket (index type) L5F
(1) Cam Belt H.D. L5G
(1) Camshaft (.416" / 272 turbo profile) L5H260
Cylinder Head Rebuild Kit L502
$649.00
as listed above
Optional Items to Cylinder Head
(A) Head Stud Kit H.D. - A.R.P. (add 45.00)
(B) Adjustable Cam Sprocket -alloy
"vernier" type (add 50.00)
*Notes: this item (L15BA) is not required when ordering L502 cylinder head kit with
L501 short block kit (it is already included with L501). We will offer a 50.00 discount
when ordering L502 and L501 together.
MOTOR RACING COMPONENTS
SPEED-PRO
RACING PRODUCTS
Engine Components3 0

ABEFG
HIFJK
L
N
O
YZ
GG
The Ford Type 9 (T9) or Hummer transmission is a 5-speed version/
conversion (an overdrive portion is added in a casting extension
behind the main case) of the venerable Type E 4-speed. The only
problem with this transmission is the 2.3 turbo engine's torque output
is near the top of T9's performance envelope. It would seem that
Ford's choice of manual and automatic transmissions were both
marginal at best for use in the XR4Ti. Even so the T9 can give better
than average service when driven sensibly. However, they do not
fair well when abused! A sure sign of problems is a "growling" input
shaft bearing. The sooner this is attended to the better. When the
input bearing fails it will take with it some, or all, of the gearing making
for an expensive repair bill. We can supply individual T9 replacement
parts from this list as requested.pNSyncronizer Ring- 1st/2nd gear M711$33.25
pO
Blocker Spring- syncronizer Z61547.55c
pP
Mainshaft w/Reverse- mainshaft w/reverse gear$308.25
pQ
Gear- 1st gear $172.79
pR
Spacer- oil scoop ring $3.50
pS
Bearing- shaft roller bearing M705$38.35
pT
Circlip- specify thickness size below$4.05
2.42, 2.48, 2.54, 2.61, 2.67mm
pU
Snap Ring- specify size below M705A.85c
1.75, 1.81, 1.87, 1.93, 1.99mm
pV
Gear- 5th driven gear $214.00
pW
Spacer- oil scoop ring $1.20
pX
Blocker Spring- syncronizer Z60785.69c
pY
Syncro Hub- 5th gear syncro hub assembly $129.50
pZ
Syncronizer Ring- 5th gear M713$26.15
pAA
Syncronizer Hub- 5th gear syncro hub $129.50
pBB
Bearing- roller bearing (1987 and up) M707$18.10
pBB
Bearing- 19mm needle (85-87) 21 required M707N$1.89
Spacer/Washer- (1985-87) 2 to 4 required M707S$1.50
pCCGear Cluster- countershaft gear cluster $379.65
pDD
Bearing- roller ball bearing M706$34.50
pEE
Circlip- specify thickness size below$2.00
1.88, 1.95, 2.12, 2.19, 2.25mm
pFF
Gear- 5th driver gear $184.25
pGG
Nut- countershaft nut (12 sided) M706N$4.35
pHH
Countershaft- shaft only Z61892$60.50
pI I
Gear- reverse idler gear $153.20
pJJ
Bushing- reverse idler bush $5.00
pKKIdler Shaft- shaft for reverse idler gear $30.50
FF
KK
JJ
II DD
EE
DD UVWAA
*see page 26 for transmission gaskets & seals
CC
HH Q
N
BBOPU
(early)
87> roller bearing assembly (1 piece)
(late)
G
D
C
M
RSTXX
pASnap Ring- front input shaft (large) M701$2.00
pB
Circlip- front input shaft (small) M701A$2.00
specify size 2.16, 2.24, 2.33, 2.42, 2.50mm
pC
Bearing- input shaft roller bearing M702$29.50
pD
Input Shaft- for XR4Ti $255.00
for Scorpio $220.75
pE
Bearing- rear input needle cage M704$7.15
pF
Syncronizer Ring- 3rd/4th gear syncro M712$26.15
pG
Blocker Spring- syncronizer Z60784.35c
pH
Snap Ring- specify size below M704A$2.00
1.63, 1.74, 1.85mm
pI
Syncronizer Assembly- 3rd/4th gear syncro unit $226.30
pJ
Gear- 3rd gear $149.30
pK
Thrust Ring- retainer 3rd gear $2.00
pLThrust Washer- thrust washer 1/2 Z61144$2.72ea.
pMGear- 2rd gear $155.00
Transmission Components3 3

Terms of Business
- Important Notice -
Most of the equipment in this catalog is intended for racing or off-highway use in the United States.
BAT Inc. ships all over the world so we must make it the responsibility of the customer to check the
legality of fitting any part to his/her car. There are many different State, Federal and provincial
regulations governing the replacement of automotive parts and BAT assumes no responsibility or
liability for their illegal use. Please check the regulations in your area before ordering.
Hours of Operation
Order desk hours are Monday through Friday 9:00 a.m. until 5:00 p.m. Eastern Time. Whenever possible orders received before 12:00
noon will be processed and shipped the same day. If anyone would like to visit our location we would like to request that you please
make an appointment before dropping by. We enjoy seeing our customers, discussing their cars, and showing them our latest
developments, however, some days or times of day are better for us to give the attention we like to offer.
Ordering Procedure
You may place an order by telephone, fax, or by mail. Ordering by telephone will connect you to a technical-sales advisor who
will help with any questions, or make ordering recommendations, if you require. Knowing your 6 digit BAT customer number,
catalog part numbers, quantities, and description of order items will help minimize any possible errors in processing your order.
Telephone orders may be placed during business hours as listed above. Fax orders may be placed anytime day or night.
Payment
Payment may be made by Visa, Master Card, Amex, Money Order or Personal Check. Orders which have been paid for by
Personal Check will be shipped only after the check has cleared (allow up to 14 days). Orders accompanied by Personal Checks
that have been bank certified will be shipped with out delay. We have no objections to shipping on a COD basis if required,
however, all COD's must be paid upon delivery with money order or certified check. When ordering by mail or fax by Visa or Master
Card be sure to include your card number and expiration date. Residents of countries outside the United States must prepay
for their goods in U.S. currency. All prices for goods shipped outside the continental United States are quoted FOB Sarasota,
FL. All shipping/duty charges must be the responsibility of the consignee at rates applicable to that particular country.
Shipping
Unless otherwise stated all orders will be shipped by United Parcel Service (UPS) surface system. We can also ship by an express
(overnight, 2 day or 3 day) service if required, check with us for details and additional charges. Items too large or heavy for UPS
service will be shipped common carrier (truck) freight collect. Optional shipping services include Surface Mail, Air Mail, and Air
Freight at current rates.
Back Orders
We dislike back orders as much as you do, and although we carry a huge inventory of merchandise it is inevitable that we will
sometimes run out of certain items. In this case we will hold the order open and ship the back ordered item directly when the item
becomes available. We
NEVER charge for back order items until they actually ship. If an item looks like it will be on back order
for longer than 4 weeks we will try and let you know the approximate time of delivery. You will then have the opportunity to reconfirm
or cancel your order.
Special Orders
Some items that we offer are available as special orders. This includes custom variations on catalog items and race prepared parts.
All special order items require a 50% deposit at the time the order is placed with the balance due at time of shipping. You will be advised
at the time of your order if any item falls into this category.
Returns
All returns must be authorized by BAT with in 30 days of the invoice date and must be sent prepaid. Returns must have an authorized RGA
number and be accompanied by a copy of the original invoice. A restocking charge of 20% may be assessed at our discretion depending on
the reason for the return. Certain parts such as bearings, books, electrical items and piston rings or any part that has been modified or installed
in any way are not returnable. Return items totaling less than $20.00 can be returned for store credit only.
Warranties
All parts are covered only by the manufacturers warranties and/or guarantees. BAT Inc. can assume no responsibility or liability
for use or application by the user. Claims for goods damaged in transit are the responsibility of the carrier. You should always
examine the contents of your package and notify the carrier immediately if there is any sign damage.
Prices and equipment are subject to change without notice.