lock FORD TAURUS 1997 Workshop Manual

Function Trade Number
Rear window wiper/washer
switch (wagon)Go to Ford
authorized
dealer
Headlamps
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood. If you are replacing the driver
side headlamp, unclip the electronic module on the
right side of the battery and move it out of the way.
2. Remove the
electrical connector
from the bulb by
pulling the connector.
3. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) about an eighth
of a turn to free it from
the bulb socket, and by
sliding the ring off the
plastic base. Keep the ring because it will be used
again to retain the new bulb.
4. Remove the old bulb from its socket by gently
pulling it straight back out of the socket. Do not
turn the bulb while you are removing it.
To install the new bulb:
Maintenance and care
148
ProCarManuals.com

1. With the flat side of
the bulb's plastic base
facing upward, insert
glass end of the bulb
into the socket. You
may need to turn the
bulb left or right to line
up the grooves in the
plastic base with the
tabs in the socket. When the grooves are aligned,
push the bulb into the socket until the plastic base
contacts the rear of the socket.
2. Slip the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating it
clockwise until you feel a ªstop.º
3. Push the electrical connector into the rear of the
plastic base until it snaps, locking it into position.
4. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.
AIMING THE HEADLAMPS
Your vehicle is equipped with a Vehicle Headlamp
Aim Device (VHAD) on each headlamp body. Each
headlamp may be proeprly aimed in the horizontal
direction (left/right) and the vertical position
(up/down).
A non-zero bubble reading does not necessarily
indicate out-of-aim headlamps. If your vehicle is not
positioned on a level surface, the slope will be
included in the level indicator. Therefore, vertical
headlamp adjustment should be performed only
when beam direction appears to be incorrect or a
level surface can not be verified.
The horizontal aim must be adjusted first. You will
need one 7 mm box wrench or open end wrench.
The following procedure assumes that the vehicle's
front structure is properly aligned. If the vehicle has
Maintenance and care
149
ProCarManuals.com

²Take care when using a power washer to clean
the engine. The high pressure fluid could
penetrate the sealed parts and cause damage.
²Do not spray with cold water to avoid cracking
the engine block.
²Cover the
highlighted areas to
prevent water
damage when
cleaning the engine.
²Never wash or rinse the engine while it is
running; water in the running engine may cause
internal damage.
Cleaning plastic exterior parts
Use a vinyl cleaner for routine cleaning of plastic.
Clean with a tar remover if necessary. Do not clean
plastic parts with thinners, solvents or
petroleum-based cleaners.
Cleaning the exterior lamps
Wash the exterior
lamps with the same
detergent you used to
wash the exterior of
your vehicle. Use glass
cleaner or tar remover
if necessary.
To avoid scratching the
lamps, do not use a dry paper towel, chemical
solvents or abrasive cleaners to clean the lamps.
Maintenance and care
153
ProCarManuals.com

FluidFord Part
Name or
EquivalentFord Part
NumberFord
Specification
Lock
cylindersE8AZ-
19A501-BPenetrating
lubricantN/A
Automatic
transaxleXT-2-QDX Motorcraft
MERCONt
AT FMERCONt
Engine oil
(Gasoline
engines)XO-5W30-
QSPMotorcraft
5W30 super
premiumWSS-
M2C153-F
and API
Certification
Mark
Constant
velocity
jointsE43Z-19590-
ACV joint
grease -
high temp.ESP-
M1C207-A
Engine
coolantE2FZ-
19549-AAFord
premium
cooling
system
fluidESE-
M97B44-A
Power
steering
pump
reservoirXT-2-QDX Motorcraft
MERCONt
AT FMERCONt
ENGINE DATA
Engine data
Engine 3.0L SOHC
V63.0L DOHC
V63.4L DOHC
V8
Cubic
inches182 183 207
Horsepower 145 @ 5250
rpm200 @ 5750
rpm235 @ 6100
rpm
Capacities and specifications
161
ProCarManuals.com

of your vehicle for maximum theft protection:
²left and right front fenders
²hood
²left and right front doors
²front and rear bumpers
²left and right rear quarter panels
²decklid
²liftgate
²engine compartment
²transaxle Engine number
The engine number is stamped on the engine block.
Capacities and specifications
167
ProCarManuals.com