key FORD WINDSTAR 1996 1.G Owner's Manual

122
*
[IP12541(ALL)02/93]
To maximize fog lamp bulb life it is recommended that the fog
lamp switch be turned off after each use prior to turning off the
headlamps.
*
[IP12544(ALL)10/94]
n
To turn the fog lamps on, push the switch. An indicator light
will glow when the lamps are on.
*
[IP12547(ALL)10/94]
n
To turn off, push the switch again.
%*
[IP12550(ALL)03/95]
ªHeadlamps Onº Alert Chime
[IP12601(ALL)03/94]
The ªheadlamps onº alert chime acts as an indicator that you
have left the headlamps or parking lights on. This continuous
chime will activate when the following conditions are present:
[IP12620(ALL)03/94]
n
The headlamp and/or parking lamps are on
[IP12640(ALL)03/94]
n
There is no key in the ignition
[IP12660(ALL)05/94]
n
The driver's door is ajar (open)
%*
[IP12700(ALL)01/93]
Daytime Running Light (DRL) System
(Canadian vehicles only)
*
[IP12800(ALL)03/95]
The Daytime Running Light (DRL) system is designed to turn
the high beam headlamps on, with a reduced light output and
without illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates when all of the
following conditions are met:
*
[IP12900(ALL)01/93]
n
the vehicle is ªrunningº
*
[IP13000(ALL)01/93]
n
the vehicle has a fully released parking brake
*
[IP13100(ALL)01/93]
n
the headlamp system is in the OFF position
*
[IP13200(ALL)01/93]
NOTE: You may notice that the lights flicker when the engine
is turned on or off. This is a normal condition.
File:wnips.ex
Update:Tue Mar 19 08:23:17 1996

Instrument Panel Controls
123
*
[IP13300(ALL)05/95]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
%*
[IP13320(ALL)02/95]
Setting the Autolamp Delay System (If equipped)
[IP13340(ALL)04/95]
By using the autolamp, you can set the headlamps to:
*
[IP13350(ALL)09/93]
n
turn on the headlamps automatically at night
*
[IP13360(ALL)09/93]
n
turn off the headlamps automatically during daylight
[IP13370(ALL)09/93]
n
keep the headlamps on for up to three minutes after you
turn the key to OFF.
[IP13380(ALL)10/93]
10-1/2 pica
art:0050157-A
The autolamp system
File:wnips.ex
Update:Tue Mar 19 08:23:17 1996

132
[SC03530(ALL)12/93]
The Speed Dependent feature comes disabled from the factory,
but can be activated at any time by using the following
procedure.
[SC03560(ALL)12/93]1.
Make sure the two front doors are securely closed.
[SC03570(ALL)04/95]2.
Insert the key into the ignition and turn first to the ON
position (the gauges on the instrument panel willnot
illuminate) and then back to the OFF position. Remove the
key and within 30 seconds:
[SC03575(ALL)12/93]3.
Press and hold the washer button on the end of the turn
signal lever.
[SC03580(ALL)04/95]4.
Within two seconds, put the key back in the ignition and
turn to the ON position.
[SC03585(ALL)06/94]5.
Hold the washer button down until a long (two second) tone
is heard. Release the button while the tone is active.
[SC03591(ALL)12/93]6.
After the long tone, a confirmation sequence will be heard.
One beep indicates the feature is inactive. Two beeps
indicates the feature is active.
[SC03595(ALL)12/93]
Repeat this procedure any time you want to cancel or reactivate
the Speed Dependent feature.
*
[SC03600(ALL)04/95]
Windshield Washer
[SC03700(ALL)08/94]
To clean the windshield, push in the washer button on the end
of the turn signal lever. For a constant spray, push and hold the
button. If the windshield wipers are off, one momentary push
results in one wipe and a longer push in three wipes and
activation of washer fluid. If the windshield wipers are in
interval mode a quick tap results in two wipe cycles and a
longer tap in three wipes and washer fluid activation.
*
[SC03800(ALL)01/93]
Do not try to clean the windshield when the washer fluid
container is empty and never activate the washers for more than
fifteen seconds continuously. This could damage the washer
pump system.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Steering Column Controls
135
[SC04415(ALL)09/93]
13-1/2 pica
art:0050017-A
The horn pad
%*
[SC04610(ALL)04/95]
Hazard Flasher Switch
*
[SC04620(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[SC04630(ALL)09/93]
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these
lamps will flash on and off. The turn signal indicators cannot be
used when the hazard lamps are flashing. Operation of the
hazard flashers does not affect operation of the brakelamps.
*
[SC04640(ALL)12/93]
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the battery
excessively. If the flashers run for longer than two hours or if
your battery is not fully charged, your battery may be drained
to the point where the vehicle will not start.
[SC04650(ALL)09/93]
The hazard flasher switch is located on top of the steering
column.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

142
%[SC11400(ALL)05/95]
Speed Control Light (Electronic Cluster Only)
*
[SC11500(ALL)03/95]
This light comes on when you turn on the speed control system
and set the speed. The light will be on whenever the speed
control is set, even if you override the set speed by pressing the
accelerator pedal or by pressing the coast button. The light will
go off when the brakes are used or the speed control system is
turned off.
[SC11600(ALL)11/93]
This light comes on briefly during the display self-test every
time you turn your ignition key to the ON position. The light
will go off when the key is turned to the START position. The
light should stay off when the self-test is done.
*
[SC11700(ALL)05/95]
This light does not indicate any problems with the speed control
system, but is a convenience to tell you when the speed control
system is actively maintaining a set speed.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Features
147
[FV04460(ALL)11/93]
10-1/2 pica
art:0050186-A
The power door lock switch in the cargo area
*
[FV04500(ALL)05/95]
NOTE: If the sliding door is open when all doors are locked
with the power door lock switch, the sliding door
automatically locks when it is closed.
*
[FV04600(ALL)01/93]
You can manually lock and unlock the doors using the manual
door locks to override the power locks.
% [FV04780(ALL)11/93]
Using the Keyless Entry System
(If equipped)
[FV04800(ALL)06/94]
If you have chosen the keyless entry system option for your
vehicle, you can lock or unlock the doors and liftgate without
using a key. The keypad is above the outside door handle on
the driver's side. See alsoRemote Entry Systemwhich follows
this description.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

148
[FV04900(ALL)10/93]
13-1/2 pica
art:0050107-A
The keyless entry system keypad
[FV05110(ALL)04/95]
When you bought your vehicle, you were given a computer
code that operates the system for your vehicle. For your
convenience, we have duplicated this code in two places.
*
[FV05120(ALL)02/95]
The code is:
*
[FV05130(ALL)02/95]
n
on your owner's wallet card found in the glove compartment
*
[FV05145(ALL)02/95]
n
taped to the computer module
[FV05160(ALL)04/95]
When you use the keyless entry system, the illuminated entry
system turns on the interior lights for 25 seconds and the
buttons on the keypad light up for five seconds.
*
[FV05170(ALL)01/93]
Do not push the keypad buttons with a key, ball-point pen,
pencil, or any other hard object since they could damage the
buttons.
%*
[FV05200(ALL)02/95]
Using the Keyless Entry System
*
[FV05300(ALL)02/95]
To operate the Keyless Entry System, you must be familiar with
the ªpersonal codeº and the ªpermanent code.º The personal
code is a code number that you select that is easy for you to
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

Features
149 remember. This is the number that you enter on the keypad to
unlock the door. The personal code can be changed as often as
you like.
[FV05400(ALL)02/95]
The permanent code is a number that is assigned to your
vehicle and can be used to program your personal code into the
system.
[FV05500(ALL)02/95]
For your convenience, one additional piece of tape with the
permanent code has been included in the glove box. Place this
additional piece of tape in a safe location where you can refer
to it when necessary. Do not put it in any location that is
accessible to unauthorized persons, since this would allow them
entrance to your vehicle.
%*
[FV06200(ALL)02/95]
Programming your Personal Code
[FV06250(ALL)02/95]
A personal code does not replace the permanent code that the
dealership gave you. The original dealer code will always work
in addition to your personal code.
*
[FV06300(ALL)02/95]
To program your own code:
*
[FV06350(ALL)02/95]1.
Select five digits for your personal code.
[FV06400(ALL)10/93]2.
Enter the permanent code.
[FV06500(ALL)11/93]3.
Within five seconds, press the 1/2 button.
[FV06600(ALL)11/93]4.
Within five seconds of pressing the 1/2 button, enter your
personal code. Press each digit within five seconds of the
previous digit.
[FV06700(ALL)11/93]5.
The keyless system registers this second code. To open your
vehicle, you can now use either code. The module
remembers only one personal code at a time. Entering a
second personal code will erase the first and replace it with
the new code.
[FV06800(ALL)10/93]6.
After you have entered your personal code, the driver's door
will unlock.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

150
*
[FV06901(ALL)02/95]
To erase your personal code:
*
[FV07001(ALL)02/95]1.
Enter the original permanent code.
[FV07101(ALL)04/95]2.
Press the 1/2 button within five seconds of step #1.
*
[FV07201(ALL)02/95]3.
Wait six seconds.
[FV07250(ALL)11/93]4.
The keyless entry system automatically erases your personal
code. The system will now only respond to the permanent
code.
[FV07270(ALL)10/93]
Do not set a code that presents the numbers in sequential order,
such as 1/2, 3/4, 5/6, 7/8, 9/0. Studies show that people who
idly press the buttons usually press a sequential pattern. Also,
do not select a code that uses the same button five times.
Thieves can easily figure out these types of codes.
%*
[FV07300(ALL)01/93]
Unlocking the Doors with the Keyless Entry System
[FV07401(ALL)05/95]
You must unlock the driver's door before you unlock any of the
other doors. If you let more than five seconds pass between
pressing numbers, the system shuts down and you have to
enter the code again. The system has shut down if the keypad
light is out. If the keyless entry system does not work properly,
use the key or Remote Entry transmitter(s) to lock and unlock
the doors or liftgate until the system can be serviced.
[FV07501(ALL)02/95]1.
To unlock the driver's door, enter the code. All codes have 5
numbers. After you press the fifth number, the driver's door
unlocks.
[FV07601(ALL)06/94]2.
To unlock the passenger's door, sliding door and liftgate,
press 3/4 within five seconds of step #1, or re-enter the code
to open the driver's door then press 3/4.
*
[FV07701(ALL)02/95]
Locking the doors with the keyless entry system
*
[FV07801(ALL)03/94]
Along with unlocking your doors, you can use the keyless entry
system to lock the doors.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

Features
151
[FV07901(ALL)06/94]
To lock all of the doors at the same time, press the 7/8 and 9/0
buttons at the same time. It is not necessary to first enter the
keypad code. This will also arm your Ford anti-theft system.
%*
[FV09301(ALL)08/94]
Battery Saver
[FV09302(ALL)06/94]
When the ignition switch is turned to OFF, the vehicle will turn
off battery voltage to the interior lamps after 45 minutes. (The
exterior lamps are not affected.) The purpose is to minimize
extended battery drain if the lights have inadvertently been left
on or if a door or the glove box is not completely closed.
However, the timer will be immediately reset to another 45
minutes if any of the following occurs:
[FV09304(ALL)11/93]
n
any door is open or closed
[FV09305(ALL)11/93]
n
the front door handle is lifted (for Illuminated Entry only)
[FV09306(ALL)11/93]
n
taking the key IN or OUT of the ignition switch
[FV09307(ALL)11/93]
n
the Keyless Entry keypad is used
[FV09308(ALL)11/93]
n
the Remote Entry transmitter is activated
%*
[FV09313(ALL)02/95]
Remote Entry System (If equipped)
[FV09316(ALL)06/94]
If your vehicle has the remote entry system, you can lock and
unlock the vehicle doors without using a key. The remote entry
system also has a personal alarm feature. The buttons that
control the system are located on the hand held transmitter that
come with your vehicle.
*
[FV09318(ALL)02/95]
The system will work with up to four transmitters. Your vehicle
came with two transmitters. Additional transmitters can be
ordered from your dealer.
*
[FV09319(ALL)02/95]
The remote entry features only operate with the ignition in the
OFF position.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996