warning light FORD WINDSTAR 1996 1.G Service Manual

Features
167
[FV14125(ALL)02/96]
7-1/2 pica art:0050292-A[FV14130(ALL)02/96]2.
Continue pushing to return the seatback to its previously
locked position.
[FV14135(ALL)02/96]
NOTE: When returning the seatback to its original position,
you may experience a slight hesitation. If so, stop
pushing the seatback momentarily, then resume. The
seatback will only return to its original position after
the seat is safely latched.
[FV14140(ALL)02/96]
Your Windstar tip slide seat has been equipped with a lock-out
safety feature which prevents the seatback from returning to its
original position until the seat pedestal latches in the tracks. If
the seat has not latched check under the seat and in the rear
tracks for possible obstructions.
[FV14145(ALL)02/96]
RWARNING
DO NOT DRIVE THE VEHICLE WITH THE TIP SLIDE
SEAT UNLATCHED.
[FV14150(ALL)02/96]
To move the seat forward or backward:
[FV14155(ALL)02/96]1.
Find the adjustment bar underneath the front part of the
seat.
[FV14160(ALL)02/96]2.
Lift the bar to unlatch the seat.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

Features
181
*
[FV18200(ALL)05/89]
Be careful that the latches are not damaged when the seats are
stored.
*
[FV18300(ALL)05/89]
To install the seat assembly:
*
[FV18400(ALL)10/90]1.
Clear the area of debris around the seat floor attachments.
[FV18500(ALL)03/94]2.
With the seatback in a folded and latched position (except
for bench seats equipped with built-in child safety seat),
place the seat assembly in your vehicle. Tip the seat
assembly forward and engage the front seat hooks onto the
forward attachment pins in the floor wells.
*
[FV18600(ALL)10/90]3.
Rotate the seat downward and engage the latch into the rear
floor attachment. Lifting of the latch handles is not required
for installation.
*
[FV18700(ALL)10/90]4.
Ensure that the latch handles are fully seated in the down
position.
[FV18800(ALL)12/93]5.
(Second row bench seat only) Before you engage the safety
belt, be sure it is not twisted. A twisted safety belt may
cause the retractor to not work properly. Remove any twist,
then insert the tongue end of the safety belt into the
detachable anchor until you hear a ªsnapº and feel the latch
engage.
[FV18820(ALL)03/94]6.
To raise the seatback, pull up on the seatback latch handle.
A slight downward pressure on the seatback (bench seat
only) will reduce effort on the latch. Rotate the seatback
upward until the latch re-engages.
*
[FV18850(ALL)05/95]
RWARNING
When reinstalling a rear seat in your vehicle it must be
placed in its original position. Improper installation of
the seat will prevent correct use of the safety belts and
could increase the risk of injury. Refer to the warning
label on the seat belt.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

Driving Your Windstar
241
*
[DR06800(ALL)01/93]
Four-Wheel Anti-lock Brakes
*
[DR06900(ALL)01/94]
The Anti-lock Brake System (ABS) prevents wheels from
completely locking up by automatically releasing and
re-applying the brakes. During ABS braking, slight brake pedal
pulsations may be felt on the driver's foot. These pulsations
represent the rapid cycling of the ABS valves. The pedal
pulsations are considered normal ABS operation, and will stop
when normal braking is resumed or when the vehicle comes to
a stop.
%*
[DR07000(ALL)12/93]
During ABS activation, a mechanical noise may be heard as the
ABS system cycles. This is normal ABS operation.
*
[DR07100(ALL)12/93]
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After the
engine is started and the ABS warning light turns off, the
system performs another test the first time the vehicle reaches
4 mph (6 km/h). A mechanical noise may be heard as the ABS
system performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
[DR07150(ALL)12/93]
6 pica art:0050147-B
The anti-lock brake system light
*
[DR07200(ALL)12/93]
You should always be careful when braking, even if your
vehicle has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

242
*
[DR07300(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[DR07320(ALL)05/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
*
[DR07350(ALL)12/93]
Ford Motor Company has not found any negative effects of
mobile radio transmitting equipment installed on vehicles with
the ABS system providing that the radio is installed according
to the radio manufacturer's instructions. However, if you have
had a mobile radio transmitter installed and the check ABS light
comes on (at any time other than immediately after turning the
key to the ON position) have your mobile radio dealer inspect
the radio installation. Also, if the ABS system is activated other
than during maximum braking, have your mobile radio
installation checked.
%*
[DR07400(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
*
[DR07500(ALL)01/93]
If the brake pedal seems ªlowº it may indicate the need for a
brake system inspection and/or service. Apply your parking
brake several times. If the condition has not improved, you
should have your brakes checked as soon as possible.
%*
[DR07600(ALL)01/93]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes very loud or if it becomes more frequent,
return the vehicle to your dealer for inspection.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

Driving Your Windstar
245
*
[DR08700(ALL)01/93]
RWARNING
When parking, do not use the gearshift in place of the
parking brake. Always set the parking brake fully and
make sure that the gearshift is securely latched in Park
(P). Turn off the ignition whenever you leave your
vehicle. Never leave your vehicle unattended while it is
running. If you do not take these precautions, your
vehicle may move unexpectedly and injure someone.
*
[DR08900(ALL)01/93]
RWARNING
If the parking brake is fully released, but the Brake
System light remains on, have the brakes checked
immediately. They may not be working properly.
*
[DR09000(ALL)02/94]
The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the service brakes fail. However, since the parking
brake does not stop your vehicle as quickly as the normal
brakes, the stopping distance will increase greatly.
%*
[DR09100(ALL)01/95]
Driving Under Special Conditions
%*
[DR09200(ALL)01/95]
Tips for Safe Driving
*
[DR09300(ALL)01/93]
As with any new vehicle, yours may drive and handle
differently from your previous vehicle. Use greater care until
you become accustomed to its features and driving
characteristics.
*
[DR09400(ALL)01/93]
Always operate your vehicle within reasonable limits. Abrupt
changes in acceleration, deceleration, turning, or combinations of
these maneuvers can cause a vehicle to behave differently than
anticipated, especially when road conditions vary.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

256
*
[DR19400(ALL)04/94]
Safety chains
*
[DR19500(ALL)01/93]
Always use safety chains between your vehicle and trailer.
Cross chains under the trailer tongue and allow slack for
turning corners. Connect safety chains to the vehicle frame or
hook retainers.Never attach chains to the bumper.
%*
[DR19600(ALL)01/93]
Trailer Brakes
*
[DR19700(ALL)01/93]
Separate trailer brakes are required on most trailers weighing
over 1,500 lbs. (680 kg).
*
[DR19800(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
%*
[DR19900(ALL)01/93]
Trailer Lamps
*
[DR20000(ALL)01/93]
Make sure your trailer lamps conform to federal and local
regulations.
*
[DR20100(ALL)01/93]
Class I Trailer Tow electrical wiring provides two circuits (right
hand and left hand) to operate trailer stop/turn tail lamps. Each
stop/turn circuit will operate one combination stop/turn light
bulb (# 1157, 3157, 2357, or 3357) on the trailer. Never add more
than one trailer light bulb to one circuit.
File:wndrs.ex
Update:Tue Mar 19 08:18:48 1996

261
Roadside Emergencies
%*
[RE00700(ALL)03/95]
Jump-Starting Your Vehicle
*
[RE00800(ALL)01/93]
Your vehicle's battery may discharge if you leave the lights or
any electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start from a booster battery
to start your vehicle.
*
[RE00900(ALL)02/95]
RWARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
*
[RE01000(ALL)02/95]
RWARNING
To protect yourself when charging a battery, always
shield your face and eyes. Make sure that you can
breathe fresh air.
%*
[RE01100(ALL)05/95]
RWARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
%*
[RE01200(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE01220(ALL)05/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
File:wnres.ex
Update:Tue Mar 19 08:18:21 1996

Servicing Your Windstar
319
*
[SV18300(ALL)05/95]
RWARNING
Continuous contact with USED motor oil has caused
cancer in laboratory mice.
*
[SV18320(ALL)05/95]
Protect your skin by washing with soap and water.
%*
[SV18400(ALL)03/95]
Engine Coolant
%*
[SV18500(ALL)02/95]
Checking the engine coolant
[SV18600(ALL)11/93]
Your vehicle's engine coolant protects the engine from
overheating in the summer and from freezing in the winter.
Check the level of the engine coolant at least once a month, but
preferably each time you stop for fuel. Simply check the coolant
reservoir, located in the engine compartment. The coolant
should stay slightly above the ªFULL COLDº mark.
*
[SV18700(ALL)01/95]
Adding engine coolant
*
[SV18900(ALL)05/95]
RWARNING
Do not put engine coolant in the container for the
windshield washer fluid.
*
[SV18920(ALL)05/95]
If sprayed to clean the glass, engine coolant or antifreeze could
make it difficult to see through the windshield.
File:wnsvs.ex
Update:Tue Mar 19 08:16:43 1996

334
*
[SV28900(ALL)05/95]
RWARNING
When using snow tires, make sure they are the same size
and grade as the tires you normally use on your vehicle.
*
[SV29000(ALL)02/95]
Do not use chains when using a temporary spare. For full size
tires, use chains on the tires only in an emergency or if the law
requires them where you live. When you use the tire chains:
*
[SV29100(ALL)01/95]
n
Make sure the chains are the right size for your tires. Use
only SAE Class ªSº chains. Other types may damage your
vehicle.
*
[SV29200(ALL)01/93]
n
Put chains on tightly with the ends held down securely.
Follow the chain manufacturer's instructions.
*
[SV29300(ALL)01/93]
n
Drive slowly. If you can hear the chains rub or bang against
your vehicle, stop the vehicle and tighten the chains. If you
continue to hear the chains rub or bang against your vehicle,
remove the chains to prevent damage to your vehicle.
*
[SV29400(ALL)10/94]
n
Avoid fully loading your vehicle if possible.
*
[SV29500(ALL)05/94]
n
Remove tire chains at the first opportunity after using them
on snow and ice. Do not use the chains on dry roads.
[SV29520(ALL)10/93]
Limited chain clearance exists with P215/70R15 tires. If your
vehicle is equipped with these tires, extra care must be observed
to avoid damage with chains.
[SV29530(ALL)10/93]
Be sure:
[SV29535(ALL)10/93]
n
The chains are fully tightened
[SV29540(ALL)05/95]
n
The vehicle is driven below 30 MPH (50 km/h)
[SV29550(ALL)10/93]
n
The vehicle is lightly loaded
[SV29560(ALL)10/93]
n
To avoid sharp turns
File:wnsvs.ex
Update:Tue Mar 19 08:16:43 1996

Servicing Your Windstar
337
%*
[SV32300(ALL)01/95]
Adding Automatic Transaxle Fluid
*
[SV32400(ALL)04/95]
The fluid type is stamped on the dipstick. Before adding any
fluid, be sure that the correct type will be used.
*
[SV32500(ALL)05/95]
Add fluid in 1/2 pint (0.25 liter) increments through the filler
tube to bring the level to the correct area on the dipstick. If an
overfill occurs, excess fluid should be removed by a qualified
technician.
%*
[SV32600(ALL)01/93]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
*
[SV32700(ALL)06/94]
NOTE: Always use Motorcraft MERCONHor equivalent
MERCONHautomatic transaxle fluid when you refill
your automatic transaxle fluid.
%*
[SV32800(ALL)02/95]
Brake Fluid
*
[SV32900(ALL)05/90]
Your vehicle is equipped with a brake fluid level indicator in
the master cylinder which lights the BRAKE warning light on
the instrument panel when the brake fluid level is low.
*
[SV33000(ALL)01/93]
Under normal circumstances, your vehicle should not use up
brake fluid rapidly. However, expect the level of the brake fluid
to slowly fall as you put more mileage on your vehicle and the
brake pads wear.
*
[SV33100(ALL)10/89]
Check the brake fluid at least once a year. You can do this by
looking at the fluid level in the plastic reservoir on the master
cylinder. The fluid level should be at or near the MAX mark.
*
[SV33200(ALL)05/95]
RWARNING
Brake fluid is toxic.
File:wnsvs.ex
Update:Tue Mar 19 08:16:43 1996