fold seats FORD WINDSTAR 1996 1.G Owners Manual

Safety Restraints
37
[SR18900(ALL)06/95]
To fold up the child seat:
[SR19000(ALL)04/95]1.
Fold the protector flap over the child seat cushion. Refer
back to Figure 3.
[SR19100(ALL)11/93]2.
Rotate the child seat cushion upward.
[SR19200(ALL)04/95]3.
Push the headrest release lever and slide the headrest
downward until it latches against the child seat cushion.
Refer back to Figures 1 and 2.
[SR19300(ALL)05/95]4.
When the child seat isnotin use, it may be folded up so
that an adult may use the vehicle's rear seat.
*
[SR19500(ALL)05/95]
Inspection after a collision
*
[SR19601(ALL)06/95]
RWARNING
All built-in child restraints, including seats, buckles,
retractors, seat latches, interlocks, and attaching hardware
should be inspected by a qualified dealer technician after
any collision.
*
[SR19620(ALL)05/95]
If the child seat was in use during a collision, Ford recommends
replacing it. However, if the collision was minor and a qualified
tehcnician finds that the child restraints do not show damage
and continue to operate properly, they do not need to be
replaced. If there is any bending of the vehicle seat back or seat
structure, it should also be replaced. Built-in child seats not in
use during a collision should also be inspected and replaced if
either damage or improper operation is noted.
*
[SR19700(ALL)05/95]
Cleaning
*
[SR19800(ALL)05/95]
Your Built-In Child Seat may be cleaned with mild soap and
water. Do not use household cleaners as they may weaken the
webbing or damage the plastic parts. For your convenience, the
liner is made to be machine washable and air dried.
File:wnsrs.ex
Update:Tue Mar 19 08:27:08 1996

Features
181
*
[FV18200(ALL)05/89]
Be careful that the latches are not damaged when the seats are
stored.
*
[FV18300(ALL)05/89]
To install the seat assembly:
*
[FV18400(ALL)10/90]1.
Clear the area of debris around the seat floor attachments.
[FV18500(ALL)03/94]2.
With the seatback in a folded and latched position (except
for bench seats equipped with built-in child safety seat),
place the seat assembly in your vehicle. Tip the seat
assembly forward and engage the front seat hooks onto the
forward attachment pins in the floor wells.
*
[FV18600(ALL)10/90]3.
Rotate the seat downward and engage the latch into the rear
floor attachment. Lifting of the latch handles is not required
for installation.
*
[FV18700(ALL)10/90]4.
Ensure that the latch handles are fully seated in the down
position.
[FV18800(ALL)12/93]5.
(Second row bench seat only) Before you engage the safety
belt, be sure it is not twisted. A twisted safety belt may
cause the retractor to not work properly. Remove any twist,
then insert the tongue end of the safety belt into the
detachable anchor until you hear a ªsnapº and feel the latch
engage.
[FV18820(ALL)03/94]6.
To raise the seatback, pull up on the seatback latch handle.
A slight downward pressure on the seatback (bench seat
only) will reduce effort on the latch. Rotate the seatback
upward until the latch re-engages.
*
[FV18850(ALL)05/95]
RWARNING
When reinstalling a rear seat in your vehicle it must be
placed in its original position. Improper installation of
the seat will prevent correct use of the safety belts and
could increase the risk of injury. Refer to the warning
label on the seat belt.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996