wiper blades FORD WINDSTAR 1998 1.G Owners Manual

Controls and Features
97
*
[CF19800(ALL)01/96]
Windshield Washer
[CF19900(ALL)01/96]
To clean the windshield, push in the washer button on the end
of the turn signal lever. For a constant spray, push and hold the
button. If the windshield wipers are off, one momentary push
results in one wipe and a longer push in three wipes and
activation of washer fluid. If the windshield wipers are in
interval mode a quick tap results in two wipe cycles and a
longer tap in three wipes and washer fluid activation.
*
[CF20000(ALL)01/96]
Do not try to clean the windshield when the washer fluid
container is empty and never activate the washers for more than
fifteen seconds continuously. This could damage the washer
pump system.
*
[CF20100(ALL)01/96]
RWARNING
Always warm up the windshield with the defroster
before you use the washer fluid. In freezing weather, the
washer solution may freeze on the windshield and
obscure your vision.
*
[CF20200(ALL)03/96]
For information about refilling the washer fluid or replacing
your windshield wiper blades, seeWindshield washer fluid and
Wipersin the Index.
%*
[CF20300(ALL)01/96]
Gearshift Lever
[CF20400(ALL)07/96]
The gearshift lever on your vehicle is mounted on the steering
column. On the end of the gearshift lever is the Overdrive
On/Off button and the OVERDRIVE OFF lamp. For additional
information about the gearshift lever and the Overdrive On/Off
button, see theDrivingchapter.
File:05wncfs.ex
Update:Tue Oct 8 10:20:34 1996

282methanol. Washer fluids containing non-methanol antifreeze
agents should be used only if they provide cold weather
protection without damaging the vehicle's paint finish, wiper
blades, and windshield washer system.
*
[MC08700(ALL)03/96]
RWARNING
Windshield washer fluid contains methanol which is
poisonous.
[MC08800(ALL)01/96]
When adding windshield washer solution, be sure to observe all
warnings indicated on the washer solution container.
%*
[MC08900(ALL)01/96]
Engine Coolant
%*
[MC09000(ALL)01/96]
Checking the Engine Coolant
[MC09100(ALL)01/96]
Your vehicle's engine coolant protects the engine from
overheating in the summer and from freezing in the winter.
Check the level of the engine coolant at least once a month, but
preferably each time you stop for fuel. Simply check the coolant
reservoir, located in the engine compartment. The coolant
should stay slightly above the ºFULL COLDª mark.
*
[MC09200(ALL)05/96]
Adding Engine Coolant
*
[MC09300(ALL)05/96]
RWARNING
Do not put engine coolant in the container for the
windshield washer fluid.
*
[MC09400(ALL)05/96]
If sprayed to clean the glass, engine coolant or antifreeze could
make it difficult to see through the windshield.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

Maintenance and Care
293
%*
[MC16200(ALL)02/96]
Wiper Blades
[MC16300(ALL)01/96]
Check the windshield wipers at least twice a year. Also check
them whenever they seem less effective than usual. Such
substances as tree sap and some hot wax treatments used by
commercial car washes reduce the effectiveness of wipers.
*
[MC16400(ALL)01/96]
If the blades do not wipe properly, clean both the windshield
and the wiper blades. Use undiluted windshield washer solution
or a mild detergent. Rinse thoroughly with clear water. Do not
use fuel, kerosene, paint thinner, or other solvents to clean your
wiper blades. These will damage your blades.
[MC16500(ALL)01/96]
Your wipers have a service feature that allows you to pull the
wiper arms and blades away from the windshield and into an
upright position. This service position allows you easy access to
the blades from either side of your vehicle.
*
[MC16600(ALL)01/96]
To reach the wiper blades easily, turn the ignition switch to
ACCESSORY and turn your wipers on. Wait for them to reach a
vertical position and turn the ignition to OFF. Moving the
wipers manually may damage them.
[MC16700(ALL)07/96]
Wiper Blade Replacement
*
[MC16800(ALL)01/96]
If the wipers still do not work properly after you clean them,
you may need to replace the wiper blade assembly. When
replacing the wiper blade assembly always use a Motorcraft part
or equivalent.
*
[MC16900(ALL)08/95]
To replace the wiper blades:
*
[MC17000(ALL)01/96]1.
Pull the wiper arm away from the windshield and into the
lock position.
[MC17100(ALL)01/96]2.
Turn the blade at an angle from the wiper arm. Squeeze the
lock tabs of the plastic clip together to release the blade and
pull the wiper blade down toward the windshield to remove
it from the arm.
File:11wnmcs.ex
Update:Tue Oct 8 10:24:50 1996

379
Index
Weight limits (GAWR, GVWR)............. 233
Wheel bearings lubricant specifications......... 325
Wheel dollies (see Towing)............... 268
Wheels
anti-theft lugnuts.................. 254
cleaning...................... 322
covers....................... 253
inspection and maintenance............. 294
Windows....................... 113
manual windows, operating............. 113
power windows, operating.............. 113
Windshield, washing................... 95
Windshield washer fluid and wipers........... 95
checking and adding fluid.............. 281
checking and replacing wiper blades......... 293
liftgate reservoir................... 281
low washer fluid light................. 19
operation....................... 95
specifications.................... 281
variable interval wipers................ 95
Windshield wipers and washer.............. 95
Wrecker towing.................... 268
File:wnixs.ex
Update:Fri Oct 11 10:49:35 1996