transmission oil GEELY FC 2008 User Guide

Disassemble lubricating oil pipe.
Take our bushing liking that shown in figure.
Take our oil seal.
Take our exterior ring of tapered shaft with special tool liking
that shown in figure.
Disassemble oil guide cover.
Transmission—Disassemble assembly
 168 

Disassemble shift guide shaft and dust-proof cover from shift
cover, and take down gasket liking that shown in figure.
Take out the shift cover oil seal with wrench liking that shown
in figure
Take out the other oil seal on shift cover with same method.
Transmission—Disassemble assembly
 173 

Press shift cover oil seal in with the method in figure, and the
distance from oil seal end surface to oil seal hole end surface
is 2.0-2.5mm after pressing it in.
Press in the other oil seal liking that shown in figure, and the
distance from oil seal end surface to oil seal hole end surface
is 0-0.5mm after pressing it in.
Assemble the gasket on shift guide shaft, and assemble dust-
proof cover in shift guide shaft, then assemble them on shift
cover.
Press a new clip spring on shift reverse shaft liking that shown
in figure.
Transmission—Disassemble assembly
 184 

Assemble lubricating oil pipe liking that shown in figure.
Press a new fork shaft clip spring in third and forth gear fork
shaft liking that in figure.
Assemble reverse gear block and fork shaft clip spring liking
that shown in figure.
Assemble third and forth gear fork shaft in clutch shell body,
and assemble third and forth shift fork in gear cover slot and
tighten them.
Bolt torque is 16N•m
Transmission—Disassemble assembly
 186 

Spread seal fastening glue on the bolts, and connect trans-
position swing lever and transposition swing lever shaft with
transposition cover with bolts, bolt torque is 16N•m
Assemble A gasket, spring, interlocking bracket and shift swing
lever on shift reverse shaft by the sequence in figure, then
press elastic cylindrical pin in the hole of shift swing lever, at
the same time, the distance from its end surface to hole should
be 0-0.5mm after pressing it in.
Press in a new clamp spring liking that shown in figure.
Take out oil with the method in figure, and assemble a new oil
seal in transmission shell body.
Transmission—Disassemble assembly
 188 

Power steering--Poser steering system
Inspection on automobile
1. Check driving belt
(a) Check whether the belt has been abraded too much with eyes, and rope is broken.
If finding any defect, change the driving belt.
Hint: Some light crack at the side of belt rib could be approved, but if belt has any crack from
its rib, it is necessary to change.
2. Exhaust air of power steering system
(a) Check the oil level.
(b) Lift up automobile body, and support it with bracket.
(c) Turn steering wheel.
(1) Turn steering wheel slowly from left and right to bottom for several times when engine extinguishes.
(d) Lay down the automobile.
(e) Start the engine to make it run at idling speed for several minutes.
(f) Rotate steering wheel.
(1) Keep engine at idling speed, and turn the steering wheel from left or right to bottom and keep this
state for 2-3 seconds, then turn it to the other direction for 2-3 seconds.
(2) Repeat (1) for several times.
(g) Engine extinguishes.
(h) Check whether there is any foam or emulsification
phenomenon.
If there is any foam or emulsification phenomenon and
it is necessary to exhaust air second time, it is necessary
to check whether the system has any leakage.
(i) Check the oil level.
3. Check the oil level
(a) Keep automobile horizontal.
(b) Extinguish the engine, and check the oil level of oil stor-
age tank.
If oil level is too low, add oil.
Power steering oil: automatic transmission oil
DEXRON’’ II or III
Hint: check whether the oil level is in the HOT mark
scope of oil storage tank, if oil is cool, check the
oil level is in COLD mark scope.
(c) Start the engine, and keep it at idling speed.
(d) Turn steering wheel from left bottom to right bottom for
several times to make oil temperature increase.
Oil temperature: 80°C
Normal Abnormal
 200 
Normal Abnormal