headlamp GEELY FC 2008 Workshop Manual

Light--Light SystemThe phenomena table1. front combination lights and tail lightPhenomena
Only one front combination light
lights
Low beam headlights do not light
(all)
distance lights do not light (all)
Distance light do not light (one
side)
Flare does not light
Front combination lights are too
dark
Only one rear combination light
lights
Rear combination lights do not light
(front combination lights are normal)
Rear combination lights do not light
(front combination lights are abnormal)Reference pages
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-LightLight SystemNotes1. Notes for changing the front combination bulb(a) When the surface of halogen bulbs (the bulb of front assembled headlamp and front fog light) touches
oil, their working life will be shorten. When it lights, it becomes hot.
(b) Because of pressured gas in halogen bulbs (the bulb of front assembled headlamp and front fog
light), the bulb may explode and pieces of broken glass disperse around. So deal with it carefully.
(c) If the time after disassembling the bulb from lamp carrier is too long, the mirror may be polluted by
dirties or hydrosphere. You should prepare a new bulb,then replace it.
(d) Replace it with the lamp of same wattage.
(e) Assemble the changing bulb on the lamp carrier firmly, or it may bring mirror mirage or water intrusion.
(f) Do not touch the black of the top of glass, or it may shorten its working life.Possible part
1.bulb
2.fuse
3.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.bulb
2.wiring harness
1.left combination switch
2.flare
3.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
3.left combination switch
4.wiring harness
1.fuse
2.relay 279 

Windshield/bodywork glass/wing mirror--Electric window control system
Avometer terminalsconditionsregular situations
16-earth(input +B signal)turn ignition switch from OFF to ON 0V → 10-14V
11-earthalways conduction
12-earthalways conduction
15-earth(input IG signal)turn ignition switch from OFF to ON 0V→10-14V
(4) Inspect other windows whether they can not actuate except window of driver seat room, when the
electric window switch locked.
2. Inspect automation function
(a) inspect basic function
(1) Turn the ignition switch to ON
(2) Inspect whether driver seat window automatic descends completely, when you press electric win-
dow main switch.
(3) Inspect whether driver seat window stop descending when driver seat window automatic descends
and press the main switch.
If the voltage and conduction do not accord with the regulations, the input side of electric window main
switch may have malfunction.
(b) Inspect the joint terminal voltage when connect the joint.
If the voltage does not accord with the regulations, electric window main switch may have malfunction.
(c) Inspect whether AUTO headlamp(LED) lights when connect the joint, turn the ignition switch from
OFF to ON.
 318 
Avometer terminalsconditionsregular situations
4-earth turn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.UP) Main switch from OFF to UP (manual operation)
9-earthturn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.DOWN)Main switch from OFF to DOWN (manual operation)
9-earthturn the ignition switch to ON, turn Off Driver
seat
window → driver seat Main switch to DOWN 0V→over9V→0V
(output P/W.DOWN)
(auto Operation)
→ windows open completely.
3. Inspect electric window main switch assembly
(a) Inspect operations
(1) Disassemble the joint of driver seat electric window main
switch and inspect the voltage and conduction among
terminals.

Windshield/bodywork glass/wing mirror--Front windscreen
Front windscreen
Change
Clues on: Please assemble as the disassembly opposite sequence. Assemble directions could
be got when necessary.
1. Disassemble right front pillar trim board assembly [68010017] (referring to page 390)
2. Disassemble left front pillar trim board assembly [68010014] (referring to page 390)
3. Disassemble inner rear mirror assembly [67010013] (referring to page 390)
4. Disassemble right sun shade [68010085] (referring to page 390)
5. Disassemble left sun shade [68010084] (referring to page 390)
6. Disassemble interior front headlamp assembly [67010075] (referring to page 390)
7. Disassemble passenger handle (referring to page 390)
8. Disassemble sun shade pothook [68010086] (referring to page 390)
9. Disassemble top interior trim board
Disassemble top interior trim board
10.Disassemble top left trim tape [68000128]
11. Disassemble top right trim tape [68000129]
12. Disassemble front windscreen sealed trim board [68000062]
(a) Use blade to cut trim tape as the drawing.
Note: Do not cut the bodywork.
(b) Disassemble rudimental trim type.
steel wire
 321  13. Disassemble front windscreen assembly [68000061]
(a) Use a steel wire to drill through windows and bodywork.
(b) Tie something like wood block at both the end of steel wire.
Clues on: Stick adhesive tape on the bodywork at work
to prevent paintwork from scraping.
Clues on: When separate window, do not damage
paintwork and interior trim board. When disassemble
front windscreen,put a plastic board between steel wire
and panel to prevent scratching the panel.
(c) Pull steel wire along front windscreen around, remove
agglutinant.
(d) Disassemble front windscreen.
Note: When cut front windscreen down, leave aggluti-
nant as much as possible on the bodywork.
14.Clean front windscreen assembly [68000061]
Use white gasoline to clean front windscreen around.
15. Assemble windscreen orientation plastic button