height adjustment GEELY FC 2008 Workshop Manual

Front suspension - Front wheel alignmentFrontRearIf toe-in is not within specification, please adjust left and
right levers of steering gear.4. Adjustment of toe-in(a) Remove dust cover fixing clip.FrontRearToe-in(Total)Front wheel alignmentAdjustment1. Inspection(a) Check tire is worn and inflation pressure is proper.
Tire inflation pressure under normal temperature:Tire size Front and rear kPa*1 It is used under the condition of speed below 160 km/h.
*2 It is used under the condition of speed above 160 km/h.
(b) Check tire run-out with dial indicator.
Tire run-out: 3.0mm.2. Measurement of vehicle heightVehicle height:
(General road)
(Coarse road)
Measuring point:
A. Height for ground and front wheel center
B. Height for ground and bolt center in front of lower
control arm
C. Height for ground and fixed bolt center of rear axle beam
D. Height for ground and rear wheel center
Note: adjust vehicle height to standard value before checking front wheel alignment.
If vehicle height does not conform to regulations, please shake upward and downward or lift vehicle
body to adjust vehicle height.3. Inspection of toe-inToe-in:Front87

Rear suspension - Rear wheel alignmentRear wheel alignmentAdjustment1. Check tire (see Page 109).
2. Measure vehicle height (see Page 87).Note: adjust vehicle height to standard value before checking
vehicle tire alignment.3. Inspection of toe-inToe-in:
(General road)
If toe-in is not within specification, check and replace relevant suspension parts.4. Inspection of camber(a) Install camber-caster-kingpin gauge or erect wheel alignment tester.
(b) Check camber.
Camber:
(general road)Toe-in (Total) (Coarse road)
Toe-in(Total)For camber could not be adjusted, therefore check suspension components are damaged or worn if
camber measuring value is not within specification, and replace parts if necessary.Camber27’45’Left-right error’(Coarse road)
CamberLeft-right errorFront101

Brake--Remove malfunction2. Check the free travel of pedal.(a) Extinguish the engine, and step brake pedal repeatedly until
there is no vacuum in vacuum booster.
(b) Press down pedal with hand until feeling the resistance,
then measure the distance of this section, liking that shown
in figure.
Free travel of pedal: 1-6mm.
If it is wrong, check the clearance of brake light switch.
Clearance of brake light switch: 0.5-2.4mm
If the clearance accords with the regulation, remove the
malfunction in brake system.3. Check the distance from pedal to floor.Release parking brake drag lever
When engine is running, step down brake pedal, then mea-
sure the distance from pedal to floor, liking that shown in figure,
Force 490 N on pedal, its distance from floor should be:
over 60mm.
If it is wrong, remove the malfunction in brake system.Brake pedal assemblyAdjustment1. Check and adjust the height of brake pedal.(a) Check the height of brake pedal.
Pedal distance from floor: 136.0-146.0mm
(b) Adjust the height of brake pedal.
(1) Disassemble lower trim board of panel.
(2) Disassemble switch joint of brake light.
(3) Loosen locking nut of brake switch, and disassemble
the switch of brake light.
(4) Loosen U-shaped clasp fixing nut of pedal lever.
(5) Turn pedal lever to adjust the height of pedal.
(6) Lock the fixing nut of lever.
Torque: 26
± ±± ±
±2 N⋅ ⋅⋅ ⋅
⋅m
(7) Assemble the switch of brake switch.
(8) Connect the switch joint of brake light.
(9) Press down the brake pedal for 5-15mm, and turn the switch of brake light to illuminate brake light,
then lock the nut.
(10) After assembling, press down the brake pedal for 5-15mm again, and confirm brake light has
illuminated.Pedal distance
from floorFree travel of
pedal Height of pedal Push rodBrake light switch136

Adjustment for headlight height Speaker cigar lighter Audio systemElectrical schematic diagram--Adjustment for headlight height Speaker cigar lighter Sound system 406