length GEELY FC 2008 Workshop Manual

Brief introduction on Geely model “FC”Basic parametersTable 1 Complete vehicle basic parametersUnit
Item nameNumber
Dimension parametersOverall
dimension
Wheel trackLength
Width
Height
Front wheel
Rear wheel
Wheel base
Front suspension
Rear suspensionPassenger numberPersonParameters±15±15±20±10±10±30±30Left lamp
Right lamp
Left lamp
Right lampLeft and
right
inclination
Down
inclinationComplete vehicle herb massMax. total massFront axle
Rear axle
Front axle
Rear axle
Weight distributionNo
load
Full
loadMin. turning diameter
Min. gound clearance
Approach angle (full load) Departure angle (full load)Front wheel camber
Kingpin inclination angle
caster angleConvergence of front wheelsRear wheel camberConvergence of rear wheelsLeft wheel: inside/outside
Right wheel:inside/outside CanderaBrief introduction on Geely model “FC” Basic parameters
Mass parameters
Traverse ability
Front wheel alignment
parameters
Rear wheel
alignment
parameters Front wheel
steering
wheel
Head lamp light
High beam
optical axisLuminous intensity of
high beam of head lamp1

Exhaust - Exhaust pipe assemblyExhaustExhaust pipe assemblyRemoving, installing and disassembling, assembling1. Remove oxygen sensor.(a) Uncouple oxygen sensor joint.
(b) Remove oxygen sensor.2. Remove exhaust pipe guard [64000051].
3. Remove front exhaust pipe together with three-way catalytic converter assembly
[64000042].
4. Remove middle exhaust pipe together with middle silencing device assembly [64000043].
5. Remove rear exhaust pipe together with rear silencing device assembly [64000044].
6. Install front exhaust pipe together with three-way catalytic converter assembly [64000042].(a) Measure free length of compression spring with vernier caliper.
Free length: 43mm
Hint: if the free length does dot reach the standard value, it is necessary to replace compres-
sion spring.
(b) Gently knock silencing device inlet seal ring to exhaust manifold with hammer and wooden block until
the surfaces are parallel and level with each other.
Notes:Gently knock gasket toward positive direction.Do not repeat using the gasket that has been removed.Do not push the gasket in by means of tightening
bolt connection.
(c) Install exhaust pipe.
Torque: 43 N.m7. Install oxygen sensor.Torque: 44 N.m9. Install rear exhaust pipe together with rear guard
assembly [64000044].(a) Measure free length of compression spring with vernier
caliper.
Free length: 40mm
Hint: if the free length does dot reach the standard value, it is necessary to replace com-
pression spring.
(b) Install tail pipe to front pipe using a new gasket.
Torque: 43 N.m10. Install front exhaust pipe guard [64000051].
11. Check there is gas leakage with exhaust system.wooden
blockGaskett8. Install middle exhaust pipe together with middle si-
lencing device assembly [64000043].Couple front intake pipe of middle exhaust pipe together with
middle silencing device assembly with outlet pipe of front ex-
haust pipe together with three-way catalytic converter using a
new gasket.Torque: 43 N.mTail pipe sideGasket65

Inside wheel38o452oOutside wheel: reference32o50Front suspension - Front wheel alignment(Coarse road)
Inside wheel39o052oOutside wheel: reference33o10Camber-031’45’Left-right error45’Caster242’45’Left-right error45’Steering shaft inclination18’45’Left-right error45’Camber-
018’45’Left-right error45’Caster230’45’Left-right error45’Steering shaft inclination1052’45’Left-right error45’A: inside
B: outsideFrontGauge If caster and steering axis inclination are not within specification, please adjust the caster and
then check parts of lower control arm is damaged or worn.(b) Loosen lock nuts at the end of transversal lever .
(c) Evenly rotate end levers of left and right rack to
adjust toe-in.
Hint: try adjusting toe-in to medium value.
(d) Ensure that the end lever length of left rack equals that
of right rack.
(e) Tighten lock nuts at the end of transversal lever.
Torque: 745 N.m
(f) Install dust cover fixing clip.
Hint: ensure that the dust cover does not distort.5. Inspection of turning angle(a) Completely rotate steering wheel to the bottom and then
measure turning angle.
Turning angle:
(General road)
(Coarse road)Wheel
alignment
tester88If left and right inside wheels are not within specification, please check the end lever length of left rack
and right rack.6. Inspection of camber, caster and steering shaft inclination(a) Install camber-caster-kingpin gauge or erect wheel alignment tester.
(b) Check camber, caster and steering-axis inclination.
Camber, caster and steering shaft inclination:
(General road)

10. Connect the in-out oil pipe assembly of power
steering gear [64000131]
(a) Assemble fixed clamp of in-out oil pipe with bolt.
Torque: 7.8 N
xm
(b) Connect in-out oil pipe with special tool.
Torque: 41 Nz
xm
Hint:
zUse torque wrench whose lever length is 345 mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
11. Connect the N0. 1 oil pipe of oil storage tank to power steering oil pump assembly.
Connect oil pipe with fixed clamp.
12. Assemble driving belt.
13. Assemble front wheel.
Torque: 103 ± 10 Nx xx x
xm
14. Add power steering oil.
15. Exhaust the air in power steering system.
16. Check whether there is any oil leakage.
17. Assemble right bottom defender board of engine [68000004].
Power steering--Power steering oil pump assembly
Special
tool
¸Ü¸Ü
¸Ü¸Ü¸Ü¸Ë¸Ë
¸Ë¸Ë¸Ë³¤³¤
³¤³¤³¤¶È¶È
¶È¶È¶È
 204 

Power steering--Power steering gear assembly
24. Check right transversal lever ball head.
25. Disassemble No.2 dust-proof cover of steering gear.
(a) Use pliers to disassemble fixed clamp.
(b) Use pliers to disassemble iron wire.
Note: do not hurt dust-proof cover.
Hint: make mark on RH and LH dust-proof cover.
Hint: disassemble the other side with same method.
26. Disassemble No.1 dust-proof cover of steering gear.
27. Disassemble terminal lever of steering gear.
(a) Use right-angled screwdriver and hammer to unclench claw
gasket.
Note: avoid knocking steering gear.
(b) Use wrench(22mm) to fix steering gear, then use special
tool to disassemble gear terminal lever.
Note: use special tool by the direction in figure.
Hint: Make mark on RH and LH gear terminal lever.
28. Assemble the parts of steering gear terminal lever.
(a) Assemble new claw gasket, and assemble gear terminal
lever temporarily.
Hint:Align pliers claw of gasket with steering gear
concave slot.
(b) Use wrench to fix steering gear, and use special tool to
tighten gear terminal lever.
Torque: 62 N
xm
Note: use special tool by the direction in figure.
Hint:use torque wrench whose lever length is 380mm.
(c) Use copper stick and hammer to concave gasket.
Note: do not hurt the steering gear.Wrench Length of
lever
Special
tool
Special tool
 208 

Power steering--Power steering gear assembly
37. Connect the bolts and nuts of left/right control arm
and control arm ball head.
Torque: 142 ± 10 Nx xx x
xm
Hint: connect the other side with same method.
Connect left lower control arm to steering knuckle with
bolt and two nuts.
38. Connect linking lever assembly of left/right front
stabilizer bar [64000097].
Use socket head wrench (5mm) to fix bolt, then connect sta-
bilizer linking lever with screw cap.
Torque: 74 ± 5 N
x xx x
xm
Hint: connect the other side with same method.
39. Connect the in-out oil pipe assembly of power steer-
ing gear [64000131].
(a) Connect the in-out oil pipe fixed clamp of power steering
gear with bolt.
Torque: 7.8 N
x xx x
xm
(b) Use special tool to connect the in-out oil pipe assembly of
power steering gear.
Torque: 41 N
x xx x
xm
Hint:
zUse the torque wrench whose lever length is
345mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
Hint: connect the other side with same method.
40. Connect the ball head at the left side of transversal
lever.
(a) Connect the ball head at the left side of transversal lever
with screw cap.
Torque: 49 ± 5 N
x xx x
xm
(b) Assemble new cotter pin.
Note: if cotter pin hole could not be aligned , tighten
the screw cap for 60 again.
Hint: connect the other side with same method.
 211 
Length of lever

Light--Front fog light joint
Clues on:
zAdjust the focus between lights of RH and LH as the drawing.
zThe value of low beam focal length is reference value for it is impossible to adjust at
level direction.
(c) Adjust vertical direction
Use the adjustable bolt A to make the headlight focus limits
to the regular.
(d) Adjust level direction
Use the adjustable bolt B to make the headlight focus limits
to the regular.
(10) Inspect front combination light whether it irradiates on the area as drawing.
(11) If not, adjust light on vertical line or level line.
Adjusting bolt “B” Adjusting bolt “A”
 288 
1209.0
939.8
Numbers for approach sequence
Distant
lightLow
beam
light
wire
wirewire
wire
wire wire
H RH and
H LH wire