turn signal GEELY FC 2008 Workshop Manual

Engine mechanism - Timing chain assembly14. Remove drive belt tensioner device.Hint: operate the jack up and down to remove bolts.15. Remove water pump components [4G18-1307110].(a) Remove 6 bolts and water pump components.16. Remove engine stabilizer bracket on engine cross
member.
17. Remove compressor.
18. Remove speed sensor.
19. Remove chain tensioner components
[4G18-1006160].Note: do not turn crankshaft before installing chain
tensioner components.20. Remove timing chain hood components
[4G18-1006140].(a) Remove 11 bolts and nuts.
(b) Remove studs with star wrench.
(c) Pry open timing chain hood from timing chain hood pro-
trusion part between cylinder head and body with screw-
driver and remove it.
Note: be careful not to damage timing chain
hood, the contact surface of cylinder head and
body.21. Remove crankshaft front oil seal assembly
[4G18-1006150].Remove oil seal with screwdriver.22. Remove speed sensor signal panel
[4G18-3600011A].
23. Remove chain tension rail components
[4G18-1006120].
24. Remove chain guide rail components
[4G18-1006130].
25. Remove timing chain [4G18-1006110].Remove it with 2 screwdrivers.
Notes:Place a piece of cloth to protect engine.In the state of timing chain separating from timing
sprocket and turning camshaft, turn crankshaft 1/4
circle to avoid valve contacting with piston.26. Install timing chain.(a) Turn crankshaft to cylinder 1 compression top dead
center position.
(1) Turn camshaft from hexagon head part of
camshaft, and align dot marks on camshaft timing
sprocket.46

Engine mechanism - Timing chain assembly(2) Use damping pulley bolts to turn crankshaft with its key
toward upward.
(b) Install timing chain on crankshaft timing sprocket and
align the chain link having yellow mark with timing mark
of crankshaft timing sprocket.
Hint: there are 3 yellow chain links on the timing chain.(c) Install crankshaft timing sprocket with special tool.
(d) Install timing chain on camshaft timing sprocket and
align the chain link having yellow mark with camshaft
timing sprocket.27. Install chain guide rail components.Torque: m28. Install chain tension rail components.Torque: 29. Install speed sensor signal panel.Install signal panel with “F” mark toward forward.Toward portSet key
Yellow
mark
Timing mark
Special tool
Color (yellow) mark
Timing mark 47

Ignition - Ignition systemSpark plug
cleaneOn-vehicle inspection1. Phase sensor(a) Turn on ignition switch but do not start engine, and place digital universal meter at DC voltage gear,
then connect 2 terminals respectively to 1# pin and 3# pin of sensor, and ensure the voltage is 12V.
(b) Start engine, and phase signal is read by 2# pin via vehicle oscilloscope.2. Speed Sensor(a) Remove speed sensor joint.
(b) Place digital universal meter at ohm gear, and connect 2 terminals respectively to 2# pin and 3# pin of
sensor, and the resistance at should be 8601/2 ±801/2.
(c) Connect speed sensor joint.
(d) Place digital universal meter at AC voltage gear, and connect 2 terminals respectively to 2# pin and 3#pin of sensor, and start engine, there should be voltage output at the moment.(It is recommended to
check with vehicle oscilloscope)IgnitionIgnition systemInspection1. Spark plug(a) Clean spark plug.
Air pressure: below 588kPa.
Time: 20 s or less
(b) Check the damage condition of spark plug and insulator. If
there is something abnormal, please replace with new spark
plug.
Recommended spark plug specification:
Made in Xianghuoju Company: K6RTC
(c) Adjust electrode gap.
Electrode gap: 0.8mm77

Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286.
1. Disassemble Radiator cover assembly (reference to page 380)
2. Disassemble left front tyre lining (reference to page 380)
3. Disassemble right front tyre lining (reference to page 380)
4. Disassemble front bumper (reference to page 380)
5. Disassemble left front combination light assembly [67000102]
(a) Disassemble three bolts
(b) Disassemble four joints
(c) Pull combination light ahead
(d) Disassemble two light seat cap and four bulbs.
Adjustments
1. Adjust front combination light focus only
(a) Parking car should accord to the following situations:
zFront combination light around does not be distorted or damaged.
zPark the car on flat road.
zTyre pressure limits to the regular number value
zThe driver is on driving seat and the car is ready to go(gasoline tank in full)
zThe car weaves fore-and-aft for many times.
(b) Inspect front combination light focus
(1) Prepare for thicker white paper
(2) Arise the paper plumb at the distance of 300cm from headlight.
(3) Make sure centerline of the car makes 90 degree angle with paper’s surface as following drawing.
(4) Draw a level line (H line) on the paper which headlight can irradiate.
(5) Draw a plumb line (V line) on the paper to across centerline of the car.
(6) Draw two level lines (V RH and V LH) in the area where two side lights can irradiate.
(7) Draw a level line(connect the middle signal of two low beam headlight) to the area where headlight
can irradiates.
Clues on: H RH and H LH lines are 0.57 lower than level line(H line)of light.
(8) Start the engine.
(9) Turn the front assembled switch to ON.
Pin
 287 

Windshield/bodywork glass/wing mirror--Electric window control system
Avometer terminalsconditionsregular situations
16-earth(input +B signal)turn ignition switch from OFF to ON 0V → 10-14V
11-earthalways conduction
12-earthalways conduction
15-earth(input IG signal)turn ignition switch from OFF to ON 0V→10-14V
(4) Inspect other windows whether they can not actuate except window of driver seat room, when the
electric window switch locked.
2. Inspect automation function
(a) inspect basic function
(1) Turn the ignition switch to ON
(2) Inspect whether driver seat window automatic descends completely, when you press electric win-
dow main switch.
(3) Inspect whether driver seat window stop descending when driver seat window automatic descends
and press the main switch.
If the voltage and conduction do not accord with the regulations, the input side of electric window main
switch may have malfunction.
(b) Inspect the joint terminal voltage when connect the joint.
If the voltage does not accord with the regulations, electric window main switch may have malfunction.
(c) Inspect whether AUTO headlamp(LED) lights when connect the joint, turn the ignition switch from
OFF to ON.
 318 
Avometer terminalsconditionsregular situations
4-earth turn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.UP) Main switch from OFF to UP (manual operation)
9-earthturn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.DOWN)Main switch from OFF to DOWN (manual operation)
9-earthturn the ignition switch to ON, turn Off Driver
seat
window → driver seat Main switch to DOWN 0V→over9V→0V
(output P/W.DOWN)
(auto Operation)
→ windows open completely.
3. Inspect electric window main switch assembly
(a) Inspect operations
(1) Disassemble the joint of driver seat electric window main
switch and inspect the voltage and conduction among
terminals.

Panel/combination instrument--combination instrument
2. Inspect output signal of vehicle speed.
(1) When vehicle run at 10km/h, inspect voltage between ter-
minal10 and terminal A1 of combination instrument assembly.
Standards: the voltage pulsates repeatedly between
0V to 5V for thirteen times.
Notes: Inspect the ignition switch “on” connects the
joint
3. Inspect speed gauge
(1) Connect a test tachometer. then startup the engine.
Notes:
zTachometer terminals polarity connects oppositely will damage interior transistors and
LEDs.
zWhen move or disassemble tachometer. do not drop on the ground or knock the surface.
(2) Compare indicted value test tachometer and combination instrument tachometer.
Standard indicted value (rmp) permitted values (rpm)
700 630-770
1,000 (900-1,100)
2,000 (1,850-2,250)
3,000 2,850-3,150
4,000 (3,800-4,200)
5,000 4,750-5,250
6,000 (5,700-6,300)
7,000 6,650-7,350
DC 13.5V, 25°C
(1) Disassemble the joint of fuel meter
(2) Turn ignition switch to ON, inspect indictor position of fuel guage.
Indictor position: F
(3) Connect short terminal1 and terminal2 of wiring harness sides. Turn ignition switch to ON, inspect
indictor position of fuel guage.
Indictor position: F
5. Inspect low fuel level indictor 4. Inspect fuel gauge
The fuel gauge has the function of sensor detection (that is
failure treatment of oil level tachometer)that is when fuel gauge
indictor is at E position, if low oil level warning light doesn”t
light, first should judge whether there have open-loop trouble of
fuel sensor or wiring harness. When sensor fails, fuel indictor
should stop at current position. But if failing time is over 20
seconds, the indictor will return to E position quickly, the in-
strument will at wire break detection. If the normal situation of
detection panel is over 20 seconds, indicator will return to normal.
A1A20
 336