turn signal GEELY MK 2008 Owner's Manual

Flashing way of malfuntion code 17 for O2 sensor (3) Each fault code will blink for three times, interval time is 3s, after blinking for the third times, after an
interval of 3s, next fault code will blink. After blinking of all fault codes is finished, they will blink from begining
again. The following diagram shows engine fault warning lamp blinking mode for oxygen sensor fault code 17.5-127Terminal No. Terminal definition
4 Power supply (-)
7 Bus (signal)
16 Power supply (+)Diagnosis connector Notes: use tester cable to connect handheld tester with diagnostic interface, turn ignition switch to ON position,
operate tester, if tester displays that communication is not possible, the vehicle or tester fails.
Inspection diagnosis
1. Check engine fault warning lamp
(1) When ignition switch is turned to ON position and engine does not run, engine warning lamp on
instrument should illuminate.
(2) When engine runs, engine fault warning lamp should go out. If it still illuminates, diagnostic system
detects system fault or abnormity.
2. Use handheld tester to check diagnostic code
(1) Connect handheld tester according to corresponding pin.
(2) Turn ignition switch to ON position, turn on main switch of handheld tester.
(3) Use handheld tester to detect and check diagnostic code, refer to fault diagnostic code table. (For
operation of handheld tester, see instruction manual of handheld tester)
3. Engine fault warning lamp displays fault code through blinking code, so professional may make fault
judgment in case of emergency.
(1)Turn ignition switch to ON position.
(2) Short signal pin (9#) and negative pole (4#) for more than 2. 5s,then disconnect them,detection fault lamp
on dashboard will blink the faults in fault code according to their occurrence sequence.See from terminal outlet
endConnect in jump way over 2.5s and
disconnect
Diagnosis connectorDiagnosis connectorEngine EFI System-
Engine EFI System

Centralized Controller System-
Function Inspectior5-133Chapter 12 Centralized Controller SystemSection 1 Function InspectiorI. Glass frame riser: 1. Glass frame riser may be operated to move within 60s after ignition switch is turned on or off; 60s after
ignition switch is turned off, glass frame riser cannot be operated to move;
2. Manual rise: press corresponding glass frame riser switch rise key, corresponding glass frame riser motor
works, glass frame rises, release rise key, it stops.
3. Manual fall: press corresponding glass frame riser switch fall key (hold time 300ms), corresponding glass
frame riser motor works, glass frame falls, release fall key, it stops.
4. Automatic fall: press corresponding glass frame riser switch fall key (hold time < 300 ms), corresponding
glass frame riser motor works, glass frame falls down to end; or fall down until rise key or fall key is pressed again.
Note:
During automatic fall of glass frame, if corresponding glass frame riser switch fall key is pressed down for more
than 300 ms, glass frame riser is changed to manual fall mode; if corresponding glass frame riser switch rise key
is pressed down for more than 300ms, glass frame riser stops work.
5. Remote window closing:
In case of remote protection, if a key is pressed down for more than 1s, perform glass frame riser automatic
rise action, left front, right front, left rear, right rear in turn.II. Central lock: 1. In case protection is deactivated, use a key to open left front door switch or press internal unlock switch to
open four door fasteners; close left front door switch, close four door fasteners.
2. Remote unlock /lock:
(1) Ignition switch opening
a. Press remote control unlock key to open four door fasteners;
b. Press remote lock key to close four door fasteners;
(2) Turn off ignition switch
a. Press remote unlock key to open four front door fasteners, at the same time turn light flashes once.
b. Press remote lock key to close four door fasteners, at the same time turn light flashes twice.
(3) When door is opened, press remote fastener, turn light will flash for three times, at the same time electric
horn beeps for three times.
(4) If the system is triggered in anti-theft condition, when remote unlock system exits protection state,
directional turn signal will flash for four times, at the same time, electric horn beeps for four times.
3. Automatic lock
When vehicle speed exceeds 30km/h, three doors will be closed.
4. Door lock priority
Central door lock should not act simultaneously with glass frame riser; when they conflict with each other,
central door lock acts with priority, while glass frame riser stops; after central door lock action is finished, glass
frame riser continue its work in previous condition.III. Front womdscreem wiper: After spray water signal is finished, the wiper acts twice.

IV. Post-defrost: 1. When engine speed exceeds 700rpm (ignition switch is turned on), defrost work is permitted.
2. Turn on defrost switch, perform defrost work for 12 minutes, if defrost switch is pressed down again during
defrost work, defrost work will stop.
3. During defrost, turn off ignition switch, cancel this defrost.V. Light control: 1. Headlight:
(1) After press remote lock key to close four doors, if remote lock key is pressed down again twice in
succession within in 2s, dipped headlight will extend lighting for 1 minute; if remote unlock key is
pressed down within 60s, dipped headlight control output will be turned off.
(2) During output of 60s low level, if ignition switch is turned on, low level output will stop.
2. Ceiling lamp:
(1) When any of the doors is opened, ceiling lamp illuminates; if door is not closed, ceiling lamp will be
turned off after 10 minutes of delay.
(2) For closing of all doors, ceiling lamp will go out after time delay of 30s;
(3) In case all doors are closed,and ceiling lamp illuminates,ignition switch is turned on,ceiling lamp goes
out.
(4) For remote unlock, ceiling lamp illuminates; in case all doors are closed and ceiling lamp illuminates,
remote lock ceiling lamp goes out.VI. Remote anti-theft 1. Protected state: press lock key on remote controller, while closing four doors, anti-theft indicator lamp will
flashes slowly, indicating that the system enters protected state, when the system is triggered, turn light of the
vehicle will flash, warning horn gives out alarm.
2. Cancel protection: press unlock key on remote controller, while opening left front door, anti-theft indicator
lamp flashes rapidly, if at least one of ignition switch, door is opened within 30 s, anti-theft indicator lamp will
go out; otherwise it will enter secondary anti-theft state.
3. Two stage type protection cancellation: while the system is in triggered state, press any key on the remote
controller, alarm sound will stop, however, the system is still in protected state, and car door is still locked; if the
system continues to receive invasion signal, alarm will ring again after brief stop. To cancel protection completely,
cancel alarm for the first time, then press unlock key once immediately;
4. Secondary anti-theft: after protection is cancelled, if any of ignition switch, door is not opened within 30s,
the system will restore alert status automatically, and lock the car door.
Distribution of centralized controller connector terminals:
Connector on wiring harness, as shown in the figure below (view from outgoing terminal):Centralized Controller System-
Function Inspectior5-134Centralized
controller

Centralized Controller System-Function Inspectior5-135Terminal No.
A1
3
4
5
6
7
8
9
10
11
14
15
19
20
21
22
24
26
27
28
29
30
31
32
33
34
35
36RY
YR
BBL
BR
BL
GR
WR
WB
BR
WG
BW
Gr
VY
BG
WG
BLW
BR
BY
BG
R
O
GR
WG
BLB
BLR
BLPower supply (+)
Speed sensor signal
Engine speed signal
IG2
Spray water signal wiper switch 7#Wiper intermittent position signal (+)
Right front door lamp switch
Left front door lamp switch
Hazard lamp switch
GND
Right rear door lamp switch
Left rear door lamp switch
Rear right glass regulator switch (down)
Rear right glass regulator switch (up)
Turn light switch (right turn)
Turn light switch (left turn)
Defrost switch
Left front door fastener unlocked signal
Left front door fastener locked signal
Anti-theft indicator lamp
Rear left glass regulator switch (down)
Rear left glass regulator switch (up)
Front right glass regulator switch (down)
Front right glass regulator switch (up)
Front left glass regulator switch (down)
Front left glass regulator switch (up)
GND
Antenna Definition of centralized controller terminals:Conductor color Terminal definitionConnector A
Connector B Connector C