brake GENESIS G70 2023 Owners Manual

Maintenance9-24
Checking the Brake Fluid Level
OIK090009
Check the fluid level in the reservoir
periodically. The fluid level should be
between MAX and MIN marks on the side
of the reservoir.
Before removing the reservoir cap and
adding brake fluid, clean the area around
the reservoir cap thoroughly to prevent
brake fluid contamination.
If the level is low, add the specified
brake fluid to the MAX level. The level
will fall with accumulated mileage. This
is a normal condition associated with
the wear of the brake linings. If the fluid
level is excessively low, we recommend
that the brake system be checked by an
authorized retailer of Genesis Branded
products.
WARNING
If the brake system requires frequent
additions of fluid, this could indicate
a leak in the brake system. We
recommend that the vehicle be
inspected by an authorized retailer of
Genesis Branded products.
WARNING
Do not let brake fluid enter into your
eyes. If brake fluid gets in your eyes,
flush your eyes with clean water for
at least 15 minutes and get immediate
medical attention.
NOTICE

[ Do not allow brake fluid to contact
the vehicle’s body paint, as it will
result in paint damage.

[ NEVER use brake fluid which has
been exposed to open air for an
extended time, as its quality cannot
be guaranteed. It should be disposed
of properly.

[ Do not use the incorrect type of
brake fluid. A few drops of mineral
based oil, such as engine oil in your
brake system can damage brake
system parts.
Information
se only the specified brake fluid (refer
to Recommended ubricants and
Capacities section in chapter 2).
BRAKE FLUID

Maintenance9-34
TIRES AND WHEELS
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:

[ Inspect your tires monthly for
proper inflation as well as wear
and damage.

[ The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.

[ Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.

[ Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.

[ ALWAYS replace tires with the
same size, type, construction and
tread pattern as each tire that
was originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.
Tire Care
For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended
tire inflation pressures and stay
within the load limits and weight
distribution recommended for your
vehicle.
OIK087002L
All specifications (sizes and
pressures) can be found on a label
attached to the driver’s side center
pillar.
Recommended Cold Tire
Inflation Pressures
All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold tires” means the
vehicle has not been driven for at
least three hours or driven less than
one mile (1.6 km).
Warm tires normally exceed
recommended cold tire pressures
by 4 to 6 psi (28 to 41 kPa). Do not
release air from warm tires to adjust
the pressure or the tires will be
under-inflated. For recommended
inflation pressure, refer to “Tire and
Wheels” section in chapter 2.

Maintenance9-36
Tire Rotation
To equalize tread wear, Genesis
Branded Vehicle recommends that
the tires be rotated according to the
maintenance schedule or sooner if
irregular wear develops.
During rotation, check the tires for
correct balance.
When rotating tires, check for uneven
wear and damage. Abnormal wear
is usually caused by incorrect tire
pressure, improper wheel alignment,
out-of-balance wheels, severe braking
or severe cornering. Look for bumps or
bulges in the tread or side of the tire.
Replace the tire if you find any of these
conditions. Replace the tire if fabric or
cord is visible. After rotation, be sure to
bring the front and rear tire pressures
to specification and check wheel lug
nuts tightness (proper torque is 79~94
lbf·ft [11~13 kgf·m].
„19 inch tire
OHI078079
Disc brake pads should be inspected
for wear whenever tires are rotated.
Information
The outside and inside of the
unsymmetrical tire is distinguishable. hen installing an unsymmetrical
tire, be sure to install the side marked outside face the outside. If the side
marked inside is installed on the
outside, it will have a negative effect
on vehicle performance.
WARNING

[ Do not use the compact spare
tire for tire rotation.

[ Do not mix bias ply and radial ply
tires under any circumstances.
This may cause unusual handling
characteristics that may cause
loss of vehicle control resulting in
an accident.

09
9-37
Wheel Alignment and Tire
Balance
The wheels on your vehicle were
aligned and balanced carefully at the
factory to give you the longest tire
life and best overall performance.
In most cases, you will not need to
have your wheels aligned again.
However, if you notice unusual tire
wear or your vehicle pulling one way
or the other, the alignment may need
to be reset.
If you notice your vehicle vibrating
when driving on a smooth road, your
wheels may need to be rebalanced.
NOTICE
Incorrect wheel weights can
damage your vehicle’s aluminum
wheels. Use only approved wheel
weights.
Tire Replacement
Tread wear indicatorTread wear indicator
OHI078080
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 1/16 inch (1.6 mm) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the band to appear
across the entire tread before
replacing the tire.
WARNING
To reduce the risk of DEATH or
SERIOUS INJURY:

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, and traction.

[ Always replace tires with the
same size as each tire that was
originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.

[ When replacing tires (or wheels),
it is recommended to replace
the two front or two rear tires (or
wheels) as a pair. Replacing just
one tire can seriously affect your
vehicle’s handling.

[ Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, Genesis Branded Vehicle
recommends that tires be
replaced after six (6) years of
normal service.

[ Heat caused by hot climates or
frequent high loading conditions
can accelerate the aging process.
Failure to follow this warning
may cause sudden tire failure,
which could lead to a loss of
vehicle control resulting in an
accident.

09
9-57
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ESC3 10
A ESP Control Module
ECU3 10A ECM
ECU2 15A ECM
HORN 20A Horn Relay
WIPER1 30A Wiper Power Relay
TCU2 15A P/N Relay, TCM
SENSOR4 10AElectronic Oil Pump Module, Brake Vacuum Switch, E/R
Junction Block (RLY.1 (Brake Vacuum Relay))
TCU1 20A TCM
WIPER2 10A IBU, ECM
SENSOR1 15ARear Sub Junction Block (Fuel Pump Relay),
[D4HB] Rail Pressure Regulating Valve, DieseL Junction
Block (RLY.1 (Fuel Filter Heater Relay))
SENSOR5 20A[G4KL] Ignition Coil #1/#2/#3/#4
[G6DP] Ignition Coil #1/#2/#3/#4/#5/#6
[D4HB] Electronic Water Pump
MODULE 10A Active Air Flap LH
SENSOR1 10A[D4HB] Glow Relay Unit, Fuel Heater & Water Separator
Sensor
ECU1 20A ECM
SENSOR3 15A[G4KL] Oxygen Sensor (Up/Down)
[G6DP] Oxygen Sensor #1/#2/#3/#4
[D4HB] Lambda Sensor #1/#2, Electronic VGT Actuator,
Fuel Metering Unit, EGR Cooing Bypass Solenoid
Vlave, PTC Heater, Mid Nox Sensor, PM Sensor,
Rear Nox Sensor

09
9-63
Consult an authorized retailer of
Genesis Branded products to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlight assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING

[Prior to working on a light, depress
the foot brake, shift to P (Park), apply
the parking brake, press the Engine
Start/Stop button to the OFF position
and take the key with you when
leaving the vehicle to avoid sudden
movement of the vehicle and to
prevent possible electric shock.

[ Be aware the bulbs may be hot and
may burn your fingers.
NOTICE
Be sure to replace the burned-out bulb
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electrical wiring system.
NOTICE
To prevent damage, do not clean the
headlight lens with chemical solvents
or strong detergents.
Information
The headlight and tail lamp lenses could
appear frosty if the vehicle is washed after
driving or the vehicle is driven at night in
wet weather. This condition is caused by
temperature difference between the lamp
inside and outside and, it does not indicate
a problem with your vehicle. hen
moisture condenses in the lamp, it will be
removed after driving with the headlight
on. The removable level may differ
depending on lamp si e, lamp position
and environmental condition. owever, if
moisture is not removed, have the vehicle
inspected by an authori ed retailer of
Genesis Branded products.
Information

[A normally functioning lamp may
flicker momentarily to stabili e the
vehicle s electrical control system.
owever, if the lamp goes out after
flickering momentarily, or continues to
flicker, have the system checked by an
authori ed retailer of Genesis Branded
products.

[ The parking lamp may not turn on
when the parking lamp switch is turned
on, but the parking lamp and headlight
switch may turn on when the headlight
switch is turned on. This may be caused
by network failure or vehicle electrical
control system malfunction. If this
occurs, have the system checked by an
authori ed retailer of Genesis Branded
products.
Information
The headlight aiming should be ad usted
after an accident or after the headlight
assembly is reinstalled at an authori ed
retailer of Genesis Branded products.
LIGHT BULBS

Maintenance9-68
APPEARANCE CARE
Exterior CareNOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp or
side view mirrors might be damaged
due to sunlight reflected from the
sign or building. To prevent damage of
the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
ashing
To help protect your vehicle’s finish from
rus
t and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish. igh-pressure washing

[ When using high-pr
essure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[ Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[ Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.

09
9-71
Bright-metal maintenance

[To remove road tar and insects, use
a tar remover, not a scraper or other
sharp object.

[ To protect the surfaces of brightmetal
parts from corrosion, apply a coating
of wax or chrome preservative and rub
to a high luster.

[ During winter weather or in coastal
areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, accelerated
rusting can occur on underbody parts
such as the fuel lines, frame, floor pan
and exhaust system, even though they
have been treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter.
Pay special attention to these areas
because it will do more harm than good
if the road grime becomes wet without
removing it. The lower edges of doors,
rocker panels, and frame members have
drain holes that should not be allowed
to clog with dirt; trapped water in these
areas can cause rusting.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
while maintaining a slow forward
speed.
Aluminum wheel maintenance
The aluminum wheels are coated with a
clear protective finish.

[Do not use abrasive cleaner, polishing
compound, solvent, or wire brushes
on aluminum wheels.

[ Clean the wheel when it has cooled.

[ Use only a mild soap or neutral
detergent, and rinse thoroughly with
water. Also, clean the wheels after
driving on salted roads.

[ Do not wash the wheels with high-
speed car wash brushes.

[ Do not use any cleaners containing
acid or alkaline detergents.

I
I-3
B
Battery........................................................................\
......................................... 9-30
Battery Recharging ........................................................................\
.................. 9-32
Battery Replacement ........................................................................\
............... 9-31
Battery Usage Recommendations ................................................................... 9-31
Reset Items ........................................................................\
.............................. 9-33
Before Driving ........................................................................\
............................... 6-4
Before Entering the Vehicle ........................................................................\
...... 6-4
Before Starting ........................................................................\
.......................... 6-4
Blind-Spot Collision-Avoidance Assist (BCA) ................................................... 7-23
Blind-Spot Collision-Avoidance Assist Malfunction and Limitations ............ 7-32
Blind-Spot Collision-Avoidance Assist Operation .......................................... 7-27
Blind-Spot Collision-Avoidance Assist Settings ............................................. 7-25
Blind-Spot View Monitor (BVM) ...................................................................... 7-50
Blind-Spot View Monitor Malfunction ........................................................... 7-51
Blind-Spot View Monitor Operation ............................................................... 7-50
Blind-Spot View Monitor Settings .................................................................. 7-50
Brake Fluid ........................................................................\
.................................. 9-24
Checking the Brake Fluid Level ..................................................................... 9-24
Braking System ........................................................................\
............................ 6-21
Anti-Lock Brake System (ABS) ..................................................................... 6-31
Auto Hold ........................................................................\
................................ 6-27
Disc Brakes Wear Indicator ........................................................................\
..... 6-22
Electronic Parking Brake (EPB) ..................................................................... 6-23
Electronic Stability Control (ESC).................................................................. 6-32
Good Braking Practices........................................................................\
........... 6-36
High Performance Brake ........................................................................\
......... 6-22
Hill-Start Assist Control (HAC) ...................................................................... 6-36
Power-Assist Brakes ........................................................................\
............... 6-21
Vehicle Stability Management (VSM) ............................................................ 6-35
Bulb Wattage ........................................................................\
.................................. 2-9

I
I-5
E
Electronic Control Suspension........................................................................\
.... 6-41
System Malfunction ........................................................................\
................ 6-41
Emission Control System ........................................................................\
............ 9-77
Engine ........................................................................\
............................................ 2-8
Engine Compartment ........................................................................\
..................... 2-7
Engine Compartment ........................................................................\
..................... 9-3
Engine Coolant ........................................................................\
............................ 9-21
Changing Coolant........................................................................\
.................... 9-23
Checking the Coolant Level ........................................................................\
.... 9-21
Engine Number ........................................................................\
............................ 2-16
Engine Oil ........................................................................\
.................................... 9-18
Checking the Engine Oil and Filter ................................................................. 9-20
Checking the Engine Oil Level ....................................................................... 9-18
Engine Start/Stop Button ........................................................................\
............... 6-5
Engine Stop/Start Button Positions ................................................................... 6-6
Remote Start ........................................................................\
.............................. 6-8
Starting the Engine ........................................................................\
.................... 6-7
Turning Off the Engine ........................................................................\
............. 6-8
Explanation of Scheduled Maintenance Items .................................................... 9-15
Brake Discs, Pads, Calipers and Rotors .......................................................... 9-17
Brake Fluid ........................................................................\
............................. 9-17
Exhaust Pipe and Muffler ........................................................................\
....... 9-17
Parking Brake ........................................................................\
.......................... 9-17
Vacuum crankcase ventilation hoses .............................................................. 9-15
Exterior Features ........................................................................\
.......................... 5-63
Hood ........................................................................\
........................................ 5-63
Trunk ........................................................................\
....................................... 5-64
Exterior Overview (I) ........................................................................\
.................... 2-2
Exterior Overview (II) ........................................................................\
................... 2-3