lock GENESIS G80 2023 Owners Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G80, Model: GENESIS G80 2023Pages: 661, PDF Size: 13.74 MB
Page 470 of 661
7-78
Driver Assistance System
Limitations of Forward Attention
Warning
Forward Attention Warning may be
limited or may not operate properly in
the following circumstances:
[ The driver is wearing sunglasses,
special glasses, infrared cutoff
glasses, refracting glasses or thick
glasses
[ The driver has heavy eye makeup
(eyeliner, mascara, color makeup,
false eyelash) or eye piercing
[ The driver’s view is blocked by his/her
hair, hat, etc.
[ The driver is winking or wearing an
eye patch on one eye
[ The driver’s face is covered partially
by a mask, muffler, etc.
[ The driver’s view is blocked by
incoming light from outside of the
vehicle
[ Light from outside, sunlight or infrared
LED light of the camera is reflected by
glasses or sunglasses
[ The driver turns or lowers his/her
head so that the face or an eye is
hidden from the camera
[ The camera is out of the range to
monitor or close within 8 in. (20 cm)
[ The driver shakes his/her head up
and down, or adverse road conditions
cause excessive vehicle vibrations
while driving
[ The driver is improperly positioned in
the driver's seat so that the driver’s
face is not detected
[ The driver is too tall or short
[ The camera is blocked by the adjusted
steering wheel height or the turned
steering wheel[ More than two people are looking at
the instrument cluster simultaneously
from the driver’s seat
[ The driver’s eyes are narrowed due to
laughing or sun glare
[ Misrecognize a picture that has a
similar size of the driver’s face
[ There are other devices using infrared
light in the vehicle
Page 486 of 661
7-94
Driver Assistance System
Smart Cruise Control disabled
OTM070115N
When the front radar cover or sensor
is covered with snow, rain, or foreign
material, it can reduce the detecting
performance and temporarily limit or
disable Smart Cruise Control.
If this occurs the ‘Smart Cruise Control
disabled. Radar blocked’ warning
message will appear for a certain period
of time on the cluster.
Smart Cruise Control will operate properly
when snow, rain or foreign material is
removed.
WARNING
( Y H Q W K R X J K W K H Z D U Q L Q J P H V V D J H G R H V
Q R W D S S H D U R Q W K H F O X V W H U 6 P D U W & U X L V H
& R Q W U R O P D \ Q R W S U R S H U O \ R S H U D W H
& $ 8 7 , 2 1
6 P D U W & U X L V H & R Q W U R O P D \ Q R W S U R S H U O \
R S H U D W H L Q D Q D U H D I R U H [ D P S O H R S H Q
W H U U D L Q Z K H U H W K H U H L V Q R W K L Q J W R
G H W H F W D I W H U W X U Q L Q J 2 1 W K H Y H K L F O H
Limitations of Smart Cruise Control
Smart Cruise Control may not operate
properly, or it may operate unexpectedly
under the following circumstances:
[ The detecting sensor or the
surroundings are contaminated or
damaged
[ Washer fluid is continuously sprayed,
or the wiper is on
[ The camera lens is contaminated due
to tinted, filmed or coated windshield,
damaged glass, or sticky foreign
material (sticker, bug, etc.) on the
glass
[ Moisture is not removed or frozen on
the windshield
[ The field of view of the front view
camera is obstructed by sun glare
[ Street light or light from an oncoming
vehicle is reflected on the wet road
surface, such as a puddle on the road
[ The temperature around the front
view camera is high or low
[ An object is placed on the dashboard
[ The surrounding is very bright
[ The surrounding is very dark, such as
in a tunnel, etc.
[ The brightness changes suddenly, for
example when entering or exiting a
tunnel
[ The brightness outside is low, and the
headlamps are not on or are not bright
[ Driving in heavy rain or snow, or thick
fog
[ Driving through steam, smoke or
shadow
Page 487 of 661
7-95
07
[ Only part of the vehicle is detected
[ The vehicle in front has no tail lights,
tail lights are located unusually, etc.
[ The brightness outside is low, and the
tail lamps are not on or are not bright
[ The rear of the front vehicle is small
or does not look normal (for example,
tilted, overturned, etc.)
[ The front vehicle’s ground clearance is
low or high
[ A vehicle suddenly cuts in front
[ Your vehicle is being towed
[ Driving through a tunnel or iron bridge
[ Driving near areas containing metal
substances, such as a construction
zone, railroad, etc.
[ An object reflecting off the front radar
such as a guardrail, nearby vehicle,
etc.
[ The bumper around the front radar is
impacted, damaged or the front radar
is out of position
[ The temperature around the front
radar is high or low
[ Driving in vast areas where there
are few vehicles or structures (for
example, desert, meadow, suburb,
etc.)
[ The vehicle in front is made of
material that does not reflect on the
front radar
[ Driving near a highway (or motorway)
interchange or tollgate
[ Driving on a slippery surface due to
snow, water puddle, ice, etc.
[ Driving on a curved road
[ The vehicle in front is detected late
[ The vehicle in front is suddenly
blocked by an obstacle
[ The vehicle in front suddenly changes
lane or suddenly reduces speed [ The vehicle in front is bent out of
shape
[ The front vehicle’s speed is fast or
slow
[ With a vehicle in front, your vehicle
changes lane at low speed
[ The vehicle in front is covered with
snow
[ Unstable driving
[ You are on a roundabout and the
vehicle in front is not detected
[ You are continuously driving in a circle
[ Driving in a parking lot
[ Driving through a construction area,
unpaved road, partial paved road,
uneven road, speed bumps, etc.
[ Driving on an incline road, curved
road, etc.
[ Driving through a roadside with trees
or streetlights
[ The adverse road conditions cause
excessive vehicle vibrations while
driving
[ Your vehicle height is low or high
due to heavy loads, abnormal tire
pressure, etc.
[ Driving through a narrow road where
trees or grass are overgrown
[ There is interference by
electromagnetic waves, such as
driving in an area with strong radio
waves or electrical noise
Page 495 of 661
7-103
07
Information
[ Highway Set Speed Auto Change
function only operates based on
the speed limits of the highway (or
motorway), it does not work with the
speed cameras.
[ When Highway Set Speed Auto Change
function is operating, the vehicle
automatically accelerates or decelerates
when the highway (or motorway) speed
limit changes.
[ The maximum set speed for Highway
Set Speed Auto Change function is 86
mph (140 km/h).
[ If the speed limit of a new road is not
updated in the navigation, Highway Set
Speed Auto Change function may not
operate properly.
[ If the speed unit is set to a unit other
than the speed unit used in your
country, Highway Set Speed Auto
Change function may not operate
properly.
/ L P L W D W L R Q V R I 1 D Y L J D W L R Q % D V H G
Smart Cruise Control
Navigation-based Smart Cruise Control
may not operate properly under the
following circumstances:
[ The navigation is not working properly
[ Map information is not transmitted
due to infotainment system's
abnormal operation
[ Speed limit and road information in
the navigation is not updated
[ The map information and the actual
road is different because of real-time
GPS data or map information error
[ The navigation searches for a route
while driving[ GPS signals are blocked in areas such
as a tunnel
[ A road that divides into two or more
roads and joins again
[ The driver goes off course the route
set in the navigation
[ The route to the destination is
changed or canceled by resetting the
navigation
[ The vehicle enters a service station or
rest area
[ Android Auto or Car Play is operating
[ The navigation cannot detect the
current vehicle position (for example,
elevated roads including overpass
adjacent to general roads or nearby
roads exist in a parallel way)
[ The navigation is being updated while
driving
[ The navigation is being restarted while
driving
[ The speed limit of some sections
changes according to the road
situations
[ Driving on a road under construction
[ Driving on a road that is controlled
[ There is bad weather, such as heavy
rain, heavy snow, etc.
[ Driving on a road that is sharply
curved
Page 514 of 661
7-122
Driver Assistance System
Limitations of Highway Driving
Assist
Highway Driving Assist and Highway
Lane Change function may not operate
properly, or may not operate under the
following circumstances:
[ The map information and the
actual road is different because the
navigation is not updated
[ The map information and the actual
road is different because of real-time
GPS data or map information error
[ The infotainment system is overloaded
by simultaneously performing
functions such as route search, video
playback, voice recognition, etc.
[ GPS signals are blocked in areas such
as a tunnel
[ The driver goes off course or the
route to the destination is changed or
canceled by resetting the navigation
[ The vehicle enters a service station or
rest area
[ Android Auto or Car Play is operating
[ The navigation cannot detect the
current vehicle position (ex: elevated
roads including overpass adjacent to
general roads or nearby roads exist in
a parallel way)
[ White single dotted lane line or road
edge cannot be detected
[ The road is temporarily controlled due
to construction, etc.
[ There is no structure, such as a
medium strip, guardrails, etc., on the
road
[ There is a changeable lane in the
direction of lane change
Information
For more details on the limitations of
the front view camera, front radar, front
corner radar and rear corner radar, refer
to “Forward Collision-Avoidance Assist
(FCA)” section in this chapter.
Information
This device complies with Part 15 of the
FCC rules.
Operation is subject to the following three
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
3. Changes or modifications not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the device.
Information
Radio frequency radiation exposure
information:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and
operated with minimum distance of 8 in.
(20 cm) between the radiator (antenna)
and your body.
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
Page 531 of 661
7-139
07
Rear Cross-Traffic Collision-
$ Y R L G D Q F H $ V V L V W 0 D O I X Q F W L R Q
and Limitations
Rear Cross-Traffic Collision-
Avoidance Assist malfunction
OTM070125N
When Rear Cross-Traffic Collision-
Avoidance Assist is not working properly,
the ‘Check Rear Cross-Traffic Safety
system’ warning message will appear on
the cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. If this occur, have the
vehicle inspected by an authorized
retailer of Genesis Branded products.
OTM070100N
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the cluster
for several seconds, and the master
(
) warning light will illuminate on the
cluster. If this occur, have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
Rear Cross-Traffic Collision-
Avoidance Assist disabled
OTM070124N
When the rear bumper around the rear-
side radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Rear Cross-
Traffic Collision-Avoidance Assist.
If this occurs, the ‘Rear Cross-Traffic
Safety system disabled. Radar blocked’
warning message will appear on the
cluster.
Rear Cross-Traffic Collision-Avoidance
Assist will operate properly when
such foreign material or trailer, etc., is
removed.
If Rear Cross-Traffic Collision-Avoidance
Assist does not operate properly after it
is removed, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Page 539 of 661
7-147
07
) R U Z D U G 5 H Y H U V H 3 D U N L Q J
Distance Warning Malfunction
D Q G 3 U H F D X W L R Q V
Forward/Reverse Parking Distance
Warning malfunction
After starting the vehicle, a beep will
sound when the gear is shifted to R
(Reverse) to indicate Forward/Reverse
Parking Distance Warning is operating
properly.
However, if one or more of the following
occurs, first check whether the ultrasonic
sensor is damaged or blocked with
foreign material. If it still does not work
properly, have the vehicle inspected by
an authorized retailer of Genesis Branded
products.
[ The audible warning does not sound.
[ The buzzer sounds intermittently.
[ The ‘Ultrasonic sensor error or
blockage’ warning message appears
on the cluster.
ORG3EV071066L
WARNING
[ ) R U Z D U G 5 H Y H U V H 3 D U N L Q J ' L V W D Q F H
: D U Q L Q J L V D V X S S O H P H Q W D O I X Q F W L R Q
7 K H R S H U D W L R Q R I ) R U Z D U G 5 H Y H U V H
3 D U N L Q J ' L V W D Q F H : D U Q L Q J F D Q E H
D I I H F W H G E \ V H Y H U D O I D F W R U V L Q F O X G L Q J
H Q Y L U R Q P H Q W D O F R Q G L W L R Q V , W L V W K H
U H V S R Q V L E L O L W \ R I W K H G U L Y H U W R D O Z D \ V
F K H F N W K H I U R Q W D Q G U H D U Y L H Z V E H I R U H
D Q G Z K L O H S D U N L Q J
[ < R X U Q H Z Y H K L F O H Z D U U D Q W \ G R H V Q R W
F R Y H U D Q \ D F F L G H Q W V R U G D P D J H W R
W K H Y H K L F O H G X H W R W K H P D O I X Q F W L R Q R I
) R U Z D U G 5 H Y H U V H 3 D U N L Q J ' L V W D Q F H
: D U Q L Q J
[ 3 D \ F O R V H D W W H Q W L R Q Z K H Q G U L Y L Q J
Q H D U R E M H F W V S H G H V W U L D Q V D Q G
H V S H F L D O O \ F K L O G U H Q 6 R P H R E M H F W V
P D \ Q R W E H G H W H F W H G E \ W K H
X O W U D V R Q L F V H Q V R U V G X H W R W K H R E M H F W V
G L V W D Q F H V L ] H R U P D W H U L D O D O O R I
Z K L F K F D Q O L P L W W K H H I I H F W L Y H Q H V V R I
W K H V H Q V R U
Page 545 of 661
7-153
07
„Rear view camera „Rear ultrasonic sensor
ORG3EV071069LORG3EV071070LThe ‘Camera error or blockage’ or
‘Ultrasonic sensor error or blockage’
warning message will appear on the
cluster if the following situations occur:
-The rear view camera or rear
ultrasonic sensor(s) is covered with
foreign material, such as snow or rain,
etc.
-There is inclement weather, such as
heavy snow, heavy rain, etc.
If this occurs, Reverse Parking Collision-
Avoidance Assist may turn off or may not
operate properly. Check whether the rear
view camera and rear ultrasonic sensors
are clean.
Limitations of Reverse Parking
Collision-Avoidance Assist
Reverse Parking Collision-Avoidance
Assist may not assist braking or warn
the driver even if there are pedestrians
or objects under the following
circumstances:
[ Any non-factory equipment or
accessory is installed
[ Your vehicle is unstable due to an
accident or other causes
[ Bumper height or rear ultrasonic
sensor installation has been modified
[ Rear view camera or rear ultrasonic
sensor(s) is damaged
[ Rear view camera or the rear
ultrasonic sensor(s) is stained with
foreign material, such as snow, dirt,
etc.
[ Rear view camera is obscured by a
light source or by inclement weather,
such as heavy rain, fog, snow, etc.
[ The surrounding is very bright or very
dark
[ Outside temperature is very high or
very low
[ The wind is either strong (above
12 mph (20 km/h)) or blowing
perpendicular to the rear bumper
[ Objects generating excessive
noise, such as vehicle horns, loud
motorcycle vehicles or truck air
brakes, are near your vehicle
[ An ultrasonic sensor with similar
frequency is near your vehicle
[ There is ground height difference
between the vehicle and the
pedestrian
[ The image of the pedestrian in the
rear view camera is indistinguishable
from the background
Page 551 of 661
7-159
07
5 H P R W H 6 P D U W 3 D U N L Q J $ V V L V W 2 S H U D W L R Q
Remote Smart Parking Assist button
3 D U N L Q J 9 L H Z E X W W R Q
3 D U N L Q J 6 D I H W \ E X W W R Q 6 P D U W N H \ ' L J L W D O N H \
ORG3EV071163ORG3EV071164ORG3EV071341N
Location Name 6 \ P E R ODescription
Inside
vehicleParking/View
button
[ Press and hold the Parking/View button to turn
on Remote Smart Parking Assist. Also, Forward/
Reverse Parking Distance warning will automatically
turn on.
However, functions may differ depending on the
situations. Refer to each function's description for
more details in the following pages.
[ Press and hold the Parking/View button while Smart
Parking or Smart Exit function is on to operate the
function.
Parking
Safety button
[ Press the Parking Safety button while Remote Smart
Parking Assist is operating to end Remote Smart
Parking Assist operation.
Smart
keyRemote Start
button
[ Press the Remote Start button after the door is locked
with the vehicle off to start the vehicle remotely.
[ Press the Remote Start button while Remote Smart
Parking or Remote Operation function is operating
to end function operation.
Forward
button
[ When using Remote Smart Parking function,
regardless of which direction button is pressed,
parking is supported while the button is pressed.
[ When using the Remote Operation function, the
vehicle moves in the direction of the button while
the button is pressed. Backward
button
Digital
keyRemote
Smart
Parking
Assist icon
[ Press the Remote Smart Parking Assist icon on
the smartphone digital key application to activate
Remote Smart Parking.
[ When using the Remote Operation function, the
vehicle moves in the direction of the icon is pushed
and moves while the icon is pushed.
[ When using Remote Smart Parking function,
regardless of which direction the icon is pushed,
parking is supported while the icon is pushed.
Page 552 of 661
7-160
Driver Assistance System
Remote Operation
Operating order
Remote Operation operates in the
following order:
1. Getting ready to remotely move
forward and backward
2. Remotely moving forward and
backward
* H W W L Q J U H D G \ W R U H P R W H O \ P R Y H I R U Z D U G
D Q G E D F N Z D U G
There are two ways to operate Remote
Operation function.
ORG3EV071165
Method (1) Using the function with
vehicle off
(1) Within a certain range from the
vehicle press the door lock (
)
button on the smart key and lock
all doors.
(2) Press and hold the Remote Start
button (
) within 4 seconds until
the vehicle starts.
[ For more details on remotely
starting the vehicle, refer to
“Remote Start” section in chapter 6.
ORG3EV071166
ORG3EV071217AU
Method (2) Using the function with
vehicle on
(1) Park the vehicle in front of the
space where you want to use
Remote Operation function, and
shift the gear to P (Park).
(2) Press and hold the Parking/View
(
) button to turn on Smart
Parking Assist. A message ‘Remote
Parking Instructions’ will appear
on the infotainment system
screen.
(3) Get out of the vehicle with the
smart key and close all doors.