mirror GENESIS G80 2023 User Guide
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G80, Model: GENESIS G80 2023Pages: 661, PDF Size: 13.74 MB
Page 240 of 661
5-46
Convenience Features
MIRRORS
Inside Rearview Mirror
Before driving your vehicle, check to
see that your inside rearview mirror is
properly positioned. Adjust the rearview
mirror so that the view through the rear
window is properly centered.
WARNING
Make sure your line of sight is not
obstructed. Do not place objects in the
rear seat, cargo area, or behind the rear
head restraints which could interfere
with your vision through the rear
window.
WARNING
To prevent serious injury during an
accident or deployment of the air bag,
do not modify the rearview mirror and
do not install a wide mirror.
WARNING
NEVER adjust the mirror while driving.
This may cause loss of vehicle control
resulting in an accident.
NOTICE
When cleaning the mirror, use a paper
towel or similar material dampened
with glass cleaner. Do not spray glass
cleaner directly on the mirror as this
may cause the liquid cleaner to enter
the mirror housing.
Electric Chromic Mirror (ECM)
(if equipped)
ORG3EV051023[A] : Indicator
Some vehicles come equipped with an
electrochromic mirror that helps control
glare while driving at night or under low
light driving conditions.
When the vehicle is running, the glare is
automatically controlled by the sensor
mounted in the rearview mirror. The
sensor detects the light level around the
vehicle, and automatically adjusts to
control the headlamp glare from vehicles
behind you.
Whenever the the gear is shifted to R
(Reverse), the mirror will automatically
go to the brightest setting in order to
improve the driver’s view behind the
vehicle.
Page 241 of 661
5-47
05
Electrochromic mirror (ECM) with
HomeLink® system (if equipped)
Your vehicle may be equipped with
a Gentex Automatic-Dimming Mirror
with an Integrated HomeLink® Wireless
Control System.
During nighttime driving, this feature
will automatically detect and reduce
rearview mirror glare. The HomeLink®
Universal Transceiver allows you to
activate your garage door(s), electric
gate, home lighting, etc.
ORG3050208N
(1) HomeLink Channel 1
(2) HomeLink Channel 2
(3) HomeLink Channel 3
(4) Garage Door Opener Status Indicator :
Closing or Closed
(5) HomeLink Operation Indicator
(6) Garage Door Opener Status Indicator :
Opening or Opened
(7) HomeLink User Interface Indicator
$ X W R P D W L F ' L P P L Q J 1 L J K W 9 L V L R Q 6 D I H W \
Page 244 of 661
5-50
Convenience Features
6. At the garage door opener motor,
(security gate motor, etc.) locate the
U / H D U QV U 6 P D U WV U 6 H WV R U U 3 U R J U D PV
button. This can usually be found
where the hanging antenna wire is
attached to the motor-head unit (see
the device’s manual to identify this
button). The name and color of the
button may vary by manufacturer.
ODL3A040504
ÃA ladder and/or second person may
simplify the following steps.
7. ) L U P O \ S U H V V D Q G U H O H D V H W K H U / H D U QV
U 6 P D U WV U 6 H WV R U U 3 U R J U D PV E X W W R Q
You now have up to 30 seconds in
which to complete the next step.
8. Return to the vehicle and firmly press,
hold for two seconds and release,
the HomeLink button up to three
times in a row slowly. Do not press
the HomeLink button rapidly. As soon
as you see the garage door start to
move, stop pressing any buttons
until a few seconds after the garage
door has come to a complete stop,
regardless of position. At this point,
programming is complete and your
device should operate when the
HomeLink button is pressed and
released.3) Two-Way Communication
Programming (For select garage
door openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
F D Q U H F H L Y H D Q G G L V S O D \ U F O R V L Q JV
R U U R S H Q L Q JV V W D W X V P H V V D J H V I U R P
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
E H L Q J U F O R V H GV R U U R S H Q H GV
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
(4), (6) in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators (4),
(6) in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.
Page 247 of 661
5-53
05
[ If the indicator (4) flashes in Orange,
it indicates that the garage door is
U & O R V L Q JV
[ The indicator (4) turns solid green
once the garage door has closed.
[ If the indicator (6) flashes in Orange,
it indicates that the garage door is
U 2 S H Q L Q JV
[ The indicator (6) turns solid green
once the garage door has fully
opened.
[ If the indicator (4) or (6) does not
turn to green, it indicates that the
last status of garage door was not
received properly. The HomeLink
mirror tries to receive the last known
status of the garage door for a few
seconds.
3) Recalling Garage Door Status
HomeLink mirror with Two-Way
Communication provides a way to view
the last stored message from the garage
door opener. In order to recall the last
known status of the last activated device,
S U H V V W K H E X W W R Q V U D Q G V 2 5 U D Q G V
simultaneously.
[ If the indicator (4) appears solid
Green, it indicates that the last
D F W L Y D W H G G H Y L F H Z D V U F O R V H GV
properly.
[ If the indicator (6) appears solid
Green, it indicates that the last
D F W L Y D W H G G H Y L F H Z D V U R S H QV S U R S H U O \ 3. Erasing HomeLink® Buttons
1) Erasing and Reprogramming a
Single HomeLink® Button:
1. Press and hold the desired HomeLink
button you want to re-program. DO
NOT release the button.
2. The HomeLink indicator light (7) will
illuminate solid green. Release the
button as soon as the HomeLink
indicator light (7) begins to flash
orange, usually about 20 seconds.
3. Proceed with the steps in the
“Programming a New HomeLink
% X W W R QV V H F W L R Q
Information
If you do not complete the re-
programming of a new device to the
button, it will revert to the previously
stored programming.
Page 251 of 661
5-57
05
Side View Mirrors
ORG3EV051024
Your vehicle is equipped with both left-
hand and right-hand side view mirrors.
The mirrors can be adjusted remotely
with the mirror adjustment control
switch. The side view mirrors can be
folded to help prevent damage when
going through an automatic car wash or
when passing through a narrow street.
The right side view mirror is convex.
Objects seen in the mirror are closer than
they appear.
Use the inside view mirror or look back
directly to determine the actual distance
of other vehicles prior to changing lanes.
Make sure to adjust the side view mirrors
to your desired position before you begin
driving.
WARNING
Do not adjust or fold the side view
mirrors while driving. This may cause
loss of vehicle control resulting in an
accident.
NOTICE
[ Do not scrape ice off the mirror face;
this may damage the surface of the
glass.
[ If the mirror is jammed with ice, do
not adjust the mirror by force. Use
an approved de-icer (not radiator
antifreeze) spray, or a sponge or soft
cloth with very warm water, or move
the vehicle to a warm place and
allow the ice to melt.
[ Do not clean the mirror with harsh
abrasives, fuel or other petroleum
based cleaning products.
Page 252 of 661
5-58
Convenience Features
Adjusting the rearview mirrors
ORG3EV051025L
Adjusting the side view mirrors:
1. Press either the L (Left side) or R
(Right side) button (1) to select the
side view mirror you would like to
adjust.
2. Use the mirror adjustment control
switch (2) to position the selected
mirror up, down, left or right.
3. After adjustment, press both L and
R button off (indicator light off) to
prevent inadvertent adjustment.
NOTICE
[ The mirrors stop moving when
they reach the maximum adjusting
angles, but the motor continues to
operate while the switch is pressed.
Do not press the switch longer than
necessary, because this can damage
the motor.
[ Do not attempt to adjust the
rearview mirrors by hand, because
this can damage the motor.
Folding the rearview mirrors
ORG3EV051026L
Folding button
The rearview mirrors can be folded or
unfolded by pressing the button.
Infotainment system setting
[ Enable on door unlock
, I S 6 H W X S
Page 253 of 661
5-59
05
NOTICE
The electric type outside rearview
mirror operates even though the Start/
Stop button is in the OFF position.
However, to prevent unnecessary
battery discharge, do not adjust the
mirrors longer than necessary while the
vehicle is not running.
NOTICE
Do not fold the electric type outside
rearview mirror by hand. It could cause
motor failure.
Reverse Parking Aid (if equipped)
ORG3EV051027
When the gear is shifted to the R
(Reverse) position, the side view mirror(s)
will rotate downwards to aid with driving
in reverse.
The state of the side view mirror button
(1) determines whether or not the mirrors
will move:
How it works
[ When the L or R button (1) is pressed
(indicator lights ON), both side view
mirrors will move.
[ If the L and R buttons (1) are not
pressed (indicator lights OFF), both
side view mirrors will not move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:
[ The Start/Stop button is pressed to
either the OFF position or the ACC
position.
[ The gear is shifted to any position
except R (Reverse).
[ The side view mirror adjustment
button is not selected.
Page 254 of 661
5-60
Convenience Features
Reverse parking aid user settings
mode
You may change the angle of the side
view mirror if it is difficult to see the rear
view with the basic downward mirror
angle provided when reversing.
When the vehicle is first delivered, the
set downward angle of the left and right
side view mirror are different to ensure
driver visibility.
1. Make sure the vehicle is stopped.
2. Depress the brake pedal and shift
the gear to R (Reverse). When L (Left)
or R (Right) button is pressed, both
side view mirror angle will move
downward to the basic set position.
3. Press either L or R button to select
the side view mirror you would like
to adjust. Then press “z, x, {, yV
switch to adjust the side view mirror
to the desired angle.
4. After adjusting the angle to save the
adjusted side view mirror angle, shift
the gear to another position other
than R (Reverse), or change the L and
R buttons to the neutral position (L
and R buttons are not pressed).
5. Set the other side view mirror
following the above procedure 1 to 4.
Resetting reverse parking aid user settings
mode
To change the side view mirror angle
back to the basic angle, shift the gear to
R (Reverse), and adjust the mirror angle
higher than when the gear is in P (Park),
N (Neutral) and D (Drive).
NOTICE
When changing the angle of both side
view mirrors, it is recommended to
change the angle one side at a time
following the procedure 1 to 4.
Page 282 of 661
5-88
Convenience Features
Limitations of High Beam Assist
High Beam Assist may not work properly
in the following situations:
[ Light from an oncoming or front
vehicle is not detected because of
lamp damage, or because it is hidden
from sight, etc.
[ Headlamp of an oncoming or front
vehicle is covered with dust, snow or
water.
[ An oncoming or front vehicle’s
headlamps are off, but the fog lamps
are on, etc.
[ There is a lamp that has a similar
shape as a vehicle’s lamp.
[ Headlamps have been damaged or
not repaired properly.
[ Headlamps are not aimed properly.
[ Driving on a narrow-curved road,
curved road, rough road, uphill or
downhill.
[ Vehicle in front is partially visible on a
crossroad or curved road.
[ There is a traffic light, reflecting sign,
flashing sign or mirror ahead.
[ There is a temporary reflector or flash
ahead (construction area).
[ The road conditions are bad such as
being wet, iced or covered with snow.
[ A vehicle suddenly appears from a
curve.
[ The vehicle is tilted from a flat tire or
is being towed.
[ Light from an oncoming or front
vehicle is not detected due to
obstacles in the air such as exhaust
fume, smoke, fog, snow, or water spay
or blizzard on the road, or fogging in
the lamp, etc.
NOTICE
For more details on the limitations
of the front view camera, refer to
“Forward Collision-Avoidance Assist
(FCA)” section in chapter 7.
WARNING
[ At times, High Beam Assist may
not work properly. The function is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.
[ When High Beam Assist does
not operate normally, change
the headlamp position manually
between high beam and low beam.
Page 307 of 661
5-113
05
WINDSHIELD DEFROSTING AND DEFOGGING
WARNING
Windshield heating
Do not use the
position during
cooling operation in extremely humid
weather. The difference between the
temperature of the outside air and that
of the windshield could cause the outer
surface of the windshield to fog up,
causing loss of visibility could cause
an accident resulting in serious injury
or death. In this case, set the mode
selection to the
position and fan
speed control to a lower speed.
[ For maximum defrost performance,
set the temperature control to the
highest temperature setting and
the fan speed control to the highest
setting.
[ If warm air to the floor is desired while
defrosting or defogging, set the mode
to the floor-defrost position.
[ Before driving, clear all snow and ice
from the windshield, rear window,
outside rearview mirrors, and all side
windows.
[ Clear all snow and ice from the
hood and air inlet in the cowl grill
to improve heater and defroster
efficiency and to reduce the
probability of fogging up the inside of
the windshield.
To Defog Inside Windshield
ORG3EV051124N
1. Select the desired fan speed.
2. Select the desired temperature.
3. Press the defroster button (
).
4. Fresh mode will be selected
automatically.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, touch
the icon once to enable Fresh mode
(indicator light OFF).
If the
position is selected, the fan
speed is automatically increased.