cruise control GENESIS G80 2023 Owner's Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G80, Model: GENESIS G80 2023Pages: 661, PDF Size: 13.74 MB
Page 489 of 661
![GENESIS G80 2023 Owners Manual 7-97
07
[ Changing lanes
ORG3EV071103[A] : Your vehicle, [B] : Lane changing vehicle
When a vehicle moves into your lane
from an adjacent lane, it cannot be
detected by the sensor until it is in t](/img/46/58824/w960_58824-488.png "GENESIS G80 2023 Owners Manual 7-97
07
[ Changing lanes
ORG3EV071103[A] : Your vehicle, [B] : Lane changing vehicle
When a vehicle moves into your lane
from an adjacent lane, it cannot be
detected by the sensor until it is in t")
7-97
07
[ Changing lanes
ORG3EV071103[A] : Your vehicle, [B] : Lane changing vehicle
When a vehicle moves into your lane
from an adjacent lane, it cannot be
detected by the sensor until it is in the
sensor's detection range. Smart Cruise
Control may not immediately detect
the vehicle when the vehicle changes
lanes abruptly. In this case, you must
maintain a safe braking distance, and
if necessary, depress the brake pedal
to reduce your driving speed in order
to maintain a safe distance.[ Detecting vehicle
ORG3EV071126
ORG3EV071089
In the following cases, some vehicles
in your lane cannot be detected by the
sensor:
-Vehicles offset to one side
-Slow-moving vehicles or sudden-
decelerating vehicles
-Vehicles with higher ground
clearance or vehicles carrying loads
that stick out of the back of the
vehicle
-Vehicles that has the front lifted due
to heavy loads
-Vehicles within approximately 6
feet(2 m) from your vehicle
-Oncoming vehicles
-Stopped vehicles
-Vehicles with small rear profile, such
as trailers
-Narrow vehicles, such as
motorcycles or bicycles
-Special vehicles
-Animals and pedestrians
Page 490 of 661
7-98
Driver Assistance System
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
In the following cases, the vehicle
in front cannot be detected by the
sensor:
-You are steering your vehicle
-Driving on narrow or sharply curved
roads
Adjust your vehicle speed by
depressing the brake pedal according
to the road and driving conditions
ahead.
ORG3EV071127
[ When a vehicle ahead disappears
at an intersection, your vehicle may
accelerate.
Always pay attention to road and
driving conditions while driving.
ORG3EV071128
[ When a vehicle in front of you merges
out of the lane, Smart Cruise Control
may not immediately detect the new
vehicle that is now in front of you.
Always pay attention to road and
driving conditions while driving.
ORG3EV071129
[ Always look out for pedestrians when
your vehicle is maintaining a distance
with the vehicle ahead.
Page 493 of 661
7-101
07
1 D Y L J D W L R Q % D V H G 6 P D U W & U X L V H
Control Operation
Operating conditions
Navigation-based Smart Cruise Control
is ready to operate if all of the following
conditions are satisfied:
[ Smart Cruise Control is operating
[ Driving on main roads of highways
Information
For more details on how to operate Smart
Cruise Control, refer to “Smart Cruise
Control (SCC)” section in this chapter.
Navigation-based Smart Cruise
Control display and control
When Navigation-based Smart Cruise
Control operates, it will be displayed on
the cluster as follows:
ORG3EV071043N
Navigation-based Smart Cruise Control
standby
If the operating conditions are satisfied,
the white indicator will illuminate.
ORG3EV071044N
Navigation-based Smart Cruise Control
operating
If temporary deceleration is required in
the standby state and Navigation-based
Smart Cruise Control is operating, the
green
symbol will illuminate on the
cluster.
If the Highway Set Speed Auto Change
function operates, the
symbol and
set speed will illuminate in green on
the cluster, and an audible warning will
sound.
Page 494 of 661
7-102
Driver Assistance System
WARNING
ORG3EV071045L
S ' U L Y H F D U H I X O O \T Z D U Q L Q J P H V V D J H Z L O O
appear in the following circumstances:
- 1 D Y L J D W L R Q E D V H G 6 P D U W & U X L V H
& R Q W U R O L V Q R W D E O H W R V O R Z G R Z Q \ R X U
Y H K L F O H W R D V D I H V S H H G
Information
Highway Curve Zone Auto Slowdown and
Highway Set Speed Auto Change function
uses the same
symbol.
Highway Curve Zone Auto Slowdown
[ Depending on the curve ahead on the
highway (or motorway), the vehicle
will decelerate, and after passing the
curve, the vehicle will accelerate to
Smart Cruise Control set speed.
[ Vehicle deceleration time may differ
depending on the vehicle speed
and the degree of the curve on the
road. The higher the driving speed,
deceleration will start faster.
Highway Set Speed Auto Change
[ Highway Set Speed Auto Change
function will operate when Smart
Cruise Control set speed and the
highway (or motorway) speed limit is
matched.
[ While Highway Set Speed Auto
Change function is operating, when
the highway (or motorway), speed
limit changes, Smart Cruise Control
set speed automatically changes to
the changed speed limit.
[ If Smart Cruise Control set speed is
adjusted different from the speed
limit, Highway Set Speed Auto Change
function will be in the standby state.
[ If Highway Set Speed Auto Change
function has changed to the standby
state by driving on a road other than
the highway (or motorway) main road,
Highway Set Speed Auto Change
function will operate again when you
drive on the main road again without
setting the set speed.
[ If Highway Set Speed Auto Change
function has changed to the standby
state by depressing the brake pedal
or pressing the
switch on the
steering wheel, press the switch
to restart the function.
[ Highway Set Speed Auto Change
function does not operate on highway
interchanges or junctions.
Page 495 of 661
7-103
07
Information
[ Highway Set Speed Auto Change
function only operates based on
the speed limits of the highway (or
motorway), it does not work with the
speed cameras.
[ When Highway Set Speed Auto Change
function is operating, the vehicle
automatically accelerates or decelerates
when the highway (or motorway) speed
limit changes.
[ The maximum set speed for Highway
Set Speed Auto Change function is 86
mph (140 km/h).
[ If the speed limit of a new road is not
updated in the navigation, Highway Set
Speed Auto Change function may not
operate properly.
[ If the speed unit is set to a unit other
than the speed unit used in your
country, Highway Set Speed Auto
Change function may not operate
properly.
/ L P L W D W L R Q V R I 1 D Y L J D W L R Q % D V H G
Smart Cruise Control
Navigation-based Smart Cruise Control
may not operate properly under the
following circumstances:
[ The navigation is not working properly
[ Map information is not transmitted
due to infotainment system's
abnormal operation
[ Speed limit and road information in
the navigation is not updated
[ The map information and the actual
road is different because of real-time
GPS data or map information error
[ The navigation searches for a route
while driving[ GPS signals are blocked in areas such
as a tunnel
[ A road that divides into two or more
roads and joins again
[ The driver goes off course the route
set in the navigation
[ The route to the destination is
changed or canceled by resetting the
navigation
[ The vehicle enters a service station or
rest area
[ Android Auto or Car Play is operating
[ The navigation cannot detect the
current vehicle position (for example,
elevated roads including overpass
adjacent to general roads or nearby
roads exist in a parallel way)
[ The navigation is being updated while
driving
[ The navigation is being restarted while
driving
[ The speed limit of some sections
changes according to the road
situations
[ Driving on a road under construction
[ Driving on a road that is controlled
[ There is bad weather, such as heavy
rain, heavy snow, etc.
[ Driving on a road that is sharply
curved
Page 498 of 661
7-106
Driver Assistance System
Information
[ A time gap could occur between the
navigation’s guidance and when
Navigation-based Smart Cruise Control
operation starts and ends.
[ The speed information on the cluster
and navigation may differ.
[ Even if you are driving at a speed lower
than Smart Cruise Control set speed,
acceleration may be limited by the
curve sections ahead.
[ If Navigation-based Smart Cruise
Control is operating while leaving the
main road to enter an interchange,
junction, rest area, etc., the function
may operate for a certain period of
time.
[ Deceleration by Navigation-based
Smart Cruise Control may feel it is not
sufficient due to road conditions such
as uneven road surfaces, narrow lanes,
etc.
Information
This device complies with Part 15 of the
FCC rules.
Operation is subject to the following three
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
3. Changes or modifications not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the device.
Information
Radio frequency radiation exposure
information:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and
operated with minimum distance of 8 in.
(20 cm) between the radiator (antenna)
and your body.
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
Page 506 of 661
7-114
Driver Assistance System
+ L J K Z D \ ' U L Y L Q J $ V V L V W R S H U D W L Q J
Highway Driving Assist operates when:
[ Driving on the main road of highways,
and turning on Highway Driving Assist
by pressing the Driving Assist (
)
button.
[ Entering the main road of highways
while Lane Following assist and Smart
Cruise Control are operating
Information
The images and colors in the cluster may
differ depending on the cluster type or
theme selected from the cluster.
Information
[ While driving on the highway (or
motorway), if Smart Cruise Control
starts operating, Highway Driving
Assist will operate.
[ When entering the main roads of
highways (or motorways) while
Smart Cruise Control is operating,
Driving Assist will not turn on if Lane
Following Assist is turned off.[ Restarting after stopping
OTM070114L
When Highway Driving Assist is
operating, your vehicle will stop if the
vehicle ahead of you stops. Also, if the
vehicle ahead of you starts moving
within 30 seconds after the stop, your
vehicle will start as well. In addition,
after the vehicle has stopped and 30
seconds have passed, the ‘Use switch
or pedal to accelerate’ message will
appear on the cluster. Depress the
accelerator pedal or operate the +
switch, - switch or
switch to start
driving.
Page 508 of 661
7-116
Driver Assistance System
[ Driving to one side within lane (if
equipped)
ORG3EV071135
When vehicle speed is above 40 mph
(60 km/h), if a vehicle around you
is driving at a close distance, your
vehicle will control steering in the
opposite direction of the vehicle to
assist in safe driving.
If there are vehicles in both sides
of the lane that are driving close to
you, the function will not veer to the
opposite side of the lane.
+ L J K Z D \ ' U L Y L Q J $ V V L V W V W D Q G E \
When the Smart Cruise Control is
temporarily canceled while Highway
Driving Assist is operating, Highway
Driving Assist will be in the standby state.
At this time, Lane Following Assist will
operate properly.
Information
[ Driving Speed Limit helps you drive
below 40 mph (60 km/h). At this time,
the vehicle decelerates due to the
vehicle ahead. After the vehicle has
decelerated, it cannot automatically
accelerate.
[ Driving Speed Limit will cancel in the
following circumstances:
-When the driver grabs the steering
wheel again
-When the driver turns on Lane
Following Assist by pressing the Lane
Driving Assist button
-When +, -,
switch or button is
operated, or the accelerator pedal or
the brake pedal is depressed
Page 511 of 661
7-119
07
Information
[ Highway Lane Change Assist operates
when the turn signal lever is positioned
at A. If the turn signal lever is released
to the center (1) before stepping on
the lane, Highway Lane Change Assist
cancels. If the turn signal lever is
released to the center (1) after stepping
on the lane, Highway Lane Change
Assist changes the lane and turns off
the turn signal after lane change is
complete.
[ When the turn signal lever is placed at
B position for a certain period of time,
the green arrow will appear. At this
time, even when the lever is released
and returns to it’s original position (1),
lane change will still be assisted.
[ While lane change is being made by the
function, the turn signal indicator will
blink even when the turn signal lever is
not held, and the turn signal indicator
will turn off when lane change is
complete.
+ L J K Z D \ / D Q H & K D Q J H $ V V L V W V W D Q G E \
Highway Lane Change Assist function
will be in the standby state when one of
the ready state condition is not satisfied,
or when entering or driving on one of the
following roads:
[ Road within a certain distance from
the tollgate on the main road of the
highway
[ The road ahead ends without an
interchange or junction
[ Road with sharp curves
[ Road with narrow lanes
[ Road that is under construction
+ L J K Z D \ / D Q H & K D Q J H $ V V L V W F D Q F H O
The function will be canceled when:
[ The turn signal lever is turned on in
the opposite direction of lane change
[ The steering wheel is steered sharply
WARNING
[ : K L O H + L J K Z D \ ' U L Y L Q J $ V V L V W L V
R S H U D W L Q J W K H I X Q F W L R Q Z L O O F D Q F H O L I
one of the following occurs:
- + L J K Z D \ ' U L Y L Q J $ V V L V W L V W X U Q H G
off
-Lane Following Assist or Smart
Cruise Control is turned off or
W H P S R U D U L O \ F D Q F H O H G
- + D Q G V R I I Z D U Q L Q J P H V V D J H L V
G L V S O D \ H G R Q W K H F O X V W H U
- 7 K H W X U Q V L J Q D O O H Y H U L V S O D F H G D W $
position
- 7 K H K D ] D U G Z D U Q L Q J I O D V K H U L V
turned on
- ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
Assist or Blind-Spot Collision-
$ Y R L G D Q F H $ V V L V W Z D U Q L Q J P H V V D J H
L V G L V S O D \ H G
- 3 R V V L E O H F R O O L V L R Q L V G H W H F W H G L Q W K H
Q H [ W O D Q H H Y H Q W K R X J K W K H U H D U H
Q R ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
Assist and Blind Spot Collision-
$ Y R L G D Q F H $ V V L V W Z D U Q L Q J
- ( Q W H U L Q J D U R D G X Q G H U F R Q V W U X F W L R Q
-The target lane to make a lane
change disappears
-The target lane to make a lane
change is not detected
- 7 K H U H L V D S U R E O H P Z L W K W X U Q V L J Q D O
lamps