power GENESIS G80 2023 Manual Online

8-15
08
Components of the Tire Mobility Kit
OSK3068011L
1. Speed-restriction label
2. Sealant bottle and label with speed restriction
3. Filling hose from sealant bottle to wheel
4. Connectors and cable for the power outlet direct connection
5. Holder for the sealant bottle
6. Compressor
7. ON/OFF switch
8. Pressure gauge for displaying the tire inflation pressure
9. Button for reducing the tire inflation pressure
10. Hose to connect compressor and sealant bottle or compressor and wheel
Strictly follow the specified sequence, otherwise the sealant may escape under high
pressure.
WARNING
Expired sealant
Do not use the Tire sealant after the sealant has expired (for example, the expiration
date on the sealant container). This can increase the risk of tire failure.

8-17
08
CAUTION
Securely install the sealant filling hose
to the valve. If not, sealant may flow
backward, possibly clogging the filling
hose.
ORG3EV081009
5. Plug the compressor power cord (4)
into the vehicle power outlet.
NOTICE
Only use the front passenger side
power outlet when connecting the
power cord.
6. With the vehicle ON
(
indicator ON), switch on
the compressor and let it run for
approximately 5~7 minutes to fill the
sealant up to proper pressure. (refer
to the Tire and Wheels, chapter 2).
The inflation pressure of the tire after
filling is unimportant and will be
checked/corrected later.
Be careful not to overinflate the tire
and stay away from the tire when
filling it.
CAUTION
Tire pressure
Do not attempt to drive your vehicle if
the tire pressure is below 200 kPa (29
psi). This could result in an accident due
to sudden tire failure.7. Switch off the compressor.
8. Detach the hoses from the sealant
bottle connector and from the tire
valve.
Return the Tire Mobility Kit to its storage
location in the vehicle.
ORG3EV081024
9. Immediately drive approximately 4~6
miles (7~10 km or, about 10min) to
evenly distribute the sealant in the
tire.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
While driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off of the
side of the road.
Call for road side service or towing.

8-18
Emergency Situations
ORG3EV081008
10. After driving approximately 4~6 miles
(7~10 km or about 10 min), stop at a
safety location.
11. Connect the filling hose (3) of the
compressor directly to the tire valve.
12. Plug the compressor power cord into
the vehicle power outlet.
13. Adjust the tire inflation pressure to the
recomended tire inflation.
With the Vehicle is ON
(
indicator ON) proceed as
follows.
-To increase the inflation pressure
: Switch on the compressor. To
check the current inflation pressure
setting, briefly switch off the
compressor.
-To reduce the inflation pressure:
Press the button (9) on the
compressor.
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tire reading,
the compressor needs to be turned off.
CAUTION
If the inflation pressure is not
maintained, drive the vehicle a second
time, refer to step 9.
Then repeat steps 10 to 13.
Use of the TMK may be ineffectual for
tire damage larger than approximately
0.16 in (4 mm).
Contact an authorized retailer of
Genesis Branded products if the tire
cannot be made roadworthy with the
Tire Mobility Kit.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.
CAUTION
Tire pressure sensor (if equipped with
TPMS)
The sealant on the tire pressure sensor
and wheel should be removed when
you replace the tire with a new one and
inspect the tire pressure sensors. You
should get this done at an authorized
retailer of Genesis Branded products.
Information
When reinstalling the repaired or replaced
tire and wheel on the vehicle, tighten the
wheel bolt to 101 ~ 116 lbf·ft (14 ~ 16
kgf·m).

8-19
08
How to Adjust Tire Pressure
ORG3EV081008
1. Park your vehicle in a safe location.
2. Connect the filling hose (3) of the
compressor directly to the tire valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tire inflation pressure to the
recomended tire inflation.
With the Vehicle is ON
(
indicator ON), proceed as
follows.
-To increase the inflation pressure
: Switch on the compressor. To
check the current inflation pressure
setting, briefly switch off the
compressor.
-To reduce the inflation pressure:
Press the button (9) on the
compressor.
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information

[The pressure gauge may show
higher than actual reading when the
compressor is running. To get an
accurate tire reading, the compressor
needs to be turned off.

[When reinstalling the repaired or
replaced tire and wheel on the vehicle,
tighten the wheel bolt to 101 ~ 116 lbf·ft
(14 ~ 16 kgf·m).
CAUTION
Do not use the sealant when the tire
pressure only needs to be adjusted.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.

9-21
09
For Best Battery Service
ORG3EV091006

[Keep the battery securely mounted.

[Keep the battery top clean and dry.

[Keep the terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.

[Rinse any spilled electrolyte from the
battery immediately with a solution of
water and baking soda.

[If the vehicle is not going to be used
for an extended time, disconnect the
battery cables.

[Inspect the battery frequently and
keep the battery clean at all times.
Leaving the battery contaminated will
shorten battery life.

[Before recharging the battery or
performing any inspections, turn off
the vehicle and turn off all electrical
equipment.
Battery Replacement
ORG3EV091052L
When replacing the battery, disconnect
negative (-) cable (1) and remove positive
(+) battery fuse box (2). Reassemble in
the reverse order of disassembly.
Information
For vehicles with power trunks, note that
the power trunk needs to be reset after
the battery has been replaced. For more
details, refer to “Power Trunk” section in
chapter 5.
NOTICE
Make sure the battery is installed
securely when the it is replaced. If the
battery vibrates while driving, the case
and electrode plate can be damaged.

9-23
09
NOTICE
AGM battery

[Absorbent Glass Matt (AGM)
batteries are maintenance-free and
have the AGM battery serviced by
an authorized retailer of Genesis
Branded products. For charging
your AGM battery, use only fully
automatic battery chargers that
are specially developed for AGM
batteries.

[When replacing the AGM battery,
use parts for replacement from
an authorized retailer of Genesis
Branded products.

[Do not open or remove the cap on
top of the battery. This may cause
leaks of internal electrolyte that
could result in severe injury.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
8 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to the
environment and human health.
Dispose of the battery according
to your local law(s) or regulation.
Reset Items
The following items may need to be reset
after the battery has been discharged or
the battery has been disconnected.

[Driving info/After recharging/
Accumulated info (items in Utility
view) (see chapter 4)

[Integrated memory system (see
chapter 5)

[Power window (see chapter 5)

[Vision roof (see chapter 5)

[Power trunk (see chapter 5)

[Climate control system (see chapter 5)

[Clock (see Infotainment system
manual)

[Infotainment system (see
Infotainment system manual)

9-31
09
WARNING
The traction grade assigned to
this tire is based on straight ahead
braking traction tests, and does not
include acceleration, cornering,
hydroplaning, or peak traction
characteristics.
Temperature - A, B & C
The temperature grades are A (the
highest), B and C representing the
tire’s resistance to the generation
of heat and its ability to dissipate
heat when tested under controlled
conditions on a specified indoor
laboratory test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life,
and excessive temperature can
lead to sudden tire failure. Grades
B and A represent higher levels of
performance on the laboratory test
wheel than the minimum required
by law.
WARNING
The temperature grade for this
tire is established for a tire that
is properly inflated and not
overloaded. Excessive speed,
under-inflation, over-inflation, or
excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden
tire failure. This may cause loss
of vehicle control resulting in an
accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim.

9-41
09
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
Module 910AOverhead Console, AMP, A/V & Navigation Head Unit,
Driver/Passenger Power Seat Module, Inverter (Rear),
Rear Seat LH/RH Heater Unit, Electro Chromic Mirror,
Rear Seat Console Remote Control Switch, SDC,
Smart Phone Wireless Charger, Data Link Connector
Module 1110AHead Lamp LH/RH, ADAS Unit (Parking),
Multifunction Switch
Module1210A IAU, IBU
A/C310AA/C Control Module, Front A/C Controller,
Rear A/C Controller
A/BAG IND.10A Instrument Cluster, Overhead Console
E-Shifter210A Electronic ATM Shift Dial
Spare15A Not Used
Module 1010A ICU Junction Block (ESU)
Module 710ADriver Door Module, Stop Lamp Switch, IBU, IAU,
Multifunction Switch
Multi Media25A A/V & Navigation Head Unit
Module 1310AICU Junction Block (ESU), A/C Control Module,
Front A/C Controller, Rear A/C Controller,
Instrument Cluster, Head-Up Display, Security Indicator
Cluster10A Instrument Cluster, Head-Up Display
IBU 210A IBU
Airbag 215ASRS Control Module, Passenger Occupant Detection
Sensor
Presafety Seat
Belt 310A Pre-Active Seat Belt Unit
Module810ARear Corner Radar LH/RH, ECS Unit, Crash Pad Switch,
ADAS Unit (Driving), ADAS Unit (Parking), Front View
Camera, Front Console Switch, Steering Tilt & Telescopic
Unit
Spare10A Not Used
Module310ARear Corner Radar LH/RH, Front Console Keyboard,
Rear Seat Console Remote Control Switch, VESS Unit,
Steering Tilt & Telescopic Unit, Front Corner Radar LH/RH,
Smart Phone Wireless Charger, Clock Spring

9-42
Maintenance
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
P/Window LH30ARear Power Window Module LH, Driver Power Window
Module
Curtain10A IBU
P/Seat PASS 225A Passenger Power Seat Module
Trunk Open10A Trunk Latch Motor
Airbag 115A SRS Control Module
E-Shifter 110A Electronic ATM Shift Dial, SCU
Module 410ADriver/Passenger Power Outside Mirror, Hazard Switch,
Rear Seat Console Remote Control Switch, Rain Sensor,
Data Link Connector, A/C Control Module,
Rear Occupant Alert (ROA) Sensor, Multifunction Switch,
Passenger Power Seat Module
P/Seat DRV 125A Driver Power Seat Module
P/Seat10A Driver Lumbar Support Unit
Power Handle15A Steering Tilt & Telescopic Unit
Module 515ADriver Door Module, Driver/Passenger Power Seat Switch,
Driver/Passenger Power Seat Module, PTL Unit,
Driver Lumbar Support Unit
IBU 110A BLE Unit, IBU, IAU, Driver/Passenger Door Outside Handle
Power Outlet20A Armrest Power Outlet
P/Seat DRV 225A Driver Power Seat Module
P/Seat PASS 125A Passenger Power Seat Module
S/Heater DRV20A Driver Power Seat Module
S/Heater PASS20A Passenger Power Seat Module
Door Lock20A Center Door Lock/Unlock Relay, Driver Door Unlock Relay
Spare10A Not Used
Module 210ACDM, P/R Junction Block (Blower Relay, Rear Heated
Relay)
Module 610AArmrest Lamp, IBU, A/V & Navigation Head Unit, IAU,
ADAS Unit (Parking), Front Console Keyboard,
Electronic ATM Shift Dial, Front Tray Lamp, VESS Unit,
Rear Seat Console Remote Control Switch, AMP,
Rear Console USB Charger
Brake Switch10A Stop Lamp Switch, IBU

9-47
09
Rear junction block
Fuse Name Fuse Rating Circuit Protected
B+4 50AICU Junction Block (Fuse(P/Seat PASS 2, Module 4,
Door Lock, Trunk Open))
B+2 30AICU Junction Block (Fuse(IBU 1, E-Shifter 1, Spare (B+),
Module 2, Module 5,
Airbag 1), IPS2, IPS5, IPS6)
B+1 50AICU Junction Block (Fuse(Brake Switch), IPS1, IPS3,
IPS4, IPS7,
Long/Short Term Load Latch Relay)
B+3 50AICU Junction Block (Fuse(P/Seat, Curtain, P/Window
LH, S/Heater DRV,
S/Heater PASS, P/Seat DRV 1, P/Seat DRV 2, P/Seat
PASS 1, Power Handle))
Charger 15A Charging Connector Lock/Unlock Relay
P/Window RH 30ARear Power Window Module RH, Passenger Power
Window Module
AMP 25A AMP
P/Door RL 15A Rear Door Latch LH
Solar Charger 2 15A SDC
P/Door PASS 15A Passenger Door Latch
Solar Charger 1 20A SDC
Presafety Seat
Belt 130A Pre-Active Seat Belt Unit
P/Door RR 15A Rear Door Latch RH
ECS 15A ECS Unit
P/Door DRV 15A Driver Door Latch
Presafety Seat
Belt 230A Pre-Active Seat Belt Unit
Child Lock 15A Child Lock/Unlock Relay
Inverter 2 10A Inverter (Rear)
S/Heater Rear LH 20A Rear Seat LH Heater Unit
Power Trunk 30A PTL Unit (Power Trunk Lid)
S/Heater Rear RH 20A Rear Seat RH Heater Unit