height adjustment GENESIS G90 2021 Owner's Manual

2-4
Safety system of your vehicle
Front seat
(1) Seat sliding forward or rearward
/ Seat cushion tilt adjustment
/ Seat cushion height adjustment
(2) Seat cushion extension adjust-
ment
(3) Seatback angle adjustment
(4) Lumbar support adjustment
(5) Seatback bolster adjustment(6) Seat position memory system
(7) Head restraint adjustment
(8) Shoulder adjustment
(9) Seat warmer
/ Seat cooler (by air)
(10) Walk-in seat switch
(for front passenger seat)
SEATS
OHI039001N [A] : Driver

2-12
Safety system of your vehicle
Seat shoulder adjustment
(for driver's seat, if equipped)
1. Push the control switch forward or
rearward to move the shoulder
angle to the desired position.
2. Release the switch once the seat
reaches the desired position.
Seatback bolster adjustment
(for driver's seat, if equipped)
1. Push the adjustment lever clock-
wise, the seatback bolster will be
adjusted inward. Push the switch
counterclockwise, the seatback
bolster will be adjusted outward.
2. Release the lever once the bolster
reaches the desired position.
Information
To adjust the bolster height to its max-
imum in the default state, operate the
lever for approximately 8 seconds.
After that, release the lever because
there is no change in height even if you
continue to operate the lever.
i
OHI038082OHI038007

2-18
Safety system of your vehicle
VIP seat mode switches
(if equipped)
Relaxation mode
Press the switch (1) to adjust both
the front passenger's seat and the
rear seat, as follows.
• Front passenger's seat
1. The seat position is adjusted for-
ward, the seatback is leaned for-
ward, and the head restraint is
lowered.
2. The head restraint is moved
rearward, and the seat cushion
tilt is lowered.
3.The seat cushion height is low-
ered.
• Rear seat
1. The seatback (including the
shoulder portion) is leaned back,
the head restraint is moved rear-
ward, and the head restraint is
lowered.
2. The seat position is adjusted for-
ward, the seat cushion tilt is
raised and the lower lumbar sup-
port is increased.
Information
Relaxation mode switches for adjust-
ing the front passenger's seat do not
operate in the following situations.
- When the Engine Start/Stop button
is in the OFF position.
- A passenger occupies the front pas-
senger's seat.
- An item occupies the front passen-
ger's seat.
- The front passenger's door is open.
- The front passenger's seatbelt is fas-
tened.
• Do not re-press the relaxation
mode switch again, while oper-
ating the seat positions for
relaxation mode. It may abruptly
stop the seat movement.
• When you operate the seat con-
trol switch while adjusting the
seat positions for the relaxation
mode, it stops the automatic
seat position adjustment. In this
case, manually adjust the seat
positions.
• Any items, which occupy the
front passenger's seat, may get
damaged while automatically
adjusting the seat positions for
the relaxation mode. Do not put
any items on the front passen-
ger's seat.
NOTICE
i
OHI038081

2-19
02
Return function
Press the switch (2) to adjust both
the front passenger's seat and the
rear seat, as follows.
• Rear seat
1. The seat position is adjusted to
the rearmost position, the seat
cushion tilt is adjusted to the
lowest position, and the lumbar
support is decreased.
2. The head restraint is lowered,
and the seatback (including the
shoulder portion) is leaned
backward.
• Front passenger's seat
1. The seat position is adjusted
rearward, and the seatback is
leaned back.
2. The seat cushion height is
raised, and the head restraint is
adjusted to the lowest height.
Information
Return function switch for adjusting
the front passenger's seat do not oper-
ate in the following situations.
- When Engine Start/Stop button is in
the OFF position.
- A passenger occupies the front pas-
senger's seat.
- An item occupies the front passen-
ger's seat.
- The front passenger's door is open.
- The front passenger's seatbelt is fas-
tened. • Do not re-press return function
switch again, while operating
the seat positions for relaxation
mode. It may abruptly stop the
seat movement.
• When you operate the control
switch while adjusting the seat
positions with return function
switch, it stops the automatic
seat position adjustment. In this
case, manually adjust the seat
positions.
NOTICE
i

2-23
02
To prevent damage, NEVER hit or
pull on the head restraints.
Front seat head restraints
The driver's and front passenger's
seats are equipped with adjustable
head restraints for the passengers
safety and comfort.
Forward and rearward adjustment
1. Push the control switch forward or
rearward to move the head
restraint.
2. Release the switch once the head
restraint reaches the desired posi-
tion.
NOTICEOHI038008
OHI038133L
• Adjust the head restraints so
the middle of the head
restraint is at the same height
as the height of the top of the
eyes.
• NEVER adjust the head
restraint position of the dri-
ver's seat when the vehicle is
in motion.
• Adjust the head restraint as
close to the passenger's head
as possible. Do not use a seat
cushion that holds the body
away from the seatback.
• Make sure the head restraint
locks into position after
adjusting it.
OHI039190N
When there is no occupant in
the rear seats, adjust the height
of the head restraints to the
lowest position. The rear seat
head restraints can reduce the
visibility of the rear area.
CAUTION

2-24
Safety system of your vehicle
Adjusting the height up and down
1. Push the control switch up to raise
or down to lower the head
restraint.
2. Release the switch once the head
restraint reaches the desired posi-
tion.
If you recline the seatback
towards the front with the head
restraint and seat cushion raised,
the head restraint may come in
contact with the sunvisor or other
parts of the vehicle.
Removal/Reinstall
To remove the head restraint:
1. Recline the seatback (2) using the
seatback angle switch (1).
2. Raise the head restraint as far as
it can go.
3. Insert a thin-pointed tool into the
head restraint adjustment pole (3),
and then remove the head
restraint (4).
NOTICE
OHI038011OHI038009
OHI038136

2-25
02
To reinstall the head restraint :
1. Recline the seatback.
2. Push the head restraint height
control switch (1) up as far as it
can go.
3. Put the head restraint poles (2).
4. Adjust the head restraint to the
appropriate height (3).
5. Recline the seatback (5) using the
seatback angle switch (4).
Rear seat head restraints
The rear seats are equipped with
head restraints in all the seating
positions for the passenger's safety
and comfort.
Manual adjustment (if equipped)
• Adjusting the height up and down
(manual, if equipped)
To raise the head restraint:
1. Pull it up to the desired position
(1).
To lower the head restraint:
1. Push and hold the release but-
ton (2) on the head restraint sup-
port.
2. Lower the head restraint to the
desired position (3).
OHI038020
OHI039134N
OHI038071

2-26
Safety system of your vehicle
Power adjustment (if equipped)
• Adjusting the height up and down
1. Push the control switch up to
raise or down to lower the head
restraint.
2. Release the switch once the
head restraint reaches the
desired position.• Adjusting the head restraints for-
ward and rearward
1. Push the control switch forward to
move the head restraint forward.
Push the control switch rearward
to move the head restraint rear-
ward.
2. Release the switch once the head
restraint reaches the desired posi-
tion.
Pay extreme caution not to dam-
age the connectors, while remov-
ing the head restraint. If the con-
nectors are damaged, the head
restraint power adjustment may
not work properly.
NOTICE
OHI038021
OHI038022

2-36
Safety system of your vehicle
Height adjustment
You can adjust the height of the
shoulder belt anchor to one of the
three different positions for maximum
comfort and safety.
The shoulder portion should be
adjusted so it lies across your chest
and midway over your shoulder near-
est the door, not over your neck.
To adjust the height of the seat belt
anchor, lower or raise the height
adjuster into an appropriate position.
To raise the height adjuster, pull it up
(1). To lower it, push it down (3) while
pressing the height adjuster button (2).
Release the button to lock the anchor
into position. Try sliding the height
adjuster to make sure that it has
locked into position.
To release your seat belt:
Press the release button (1) in the
locking buckle.
When it is released, the belt should
automatically draw back into the
retractor. If this does not happen,
check the belt to be sure it is not twist-
ed, then try again.
OHI038142
OHI038036
■Front seat

3-17
03
Recalling Positions from
Memory
1. Check that the gear is in P (Park)
while the Engine Start/Stop button
is in the ON position.
2. Press the desired memory button
(1 or 2). The system will beep
once, and then the driver's seat
position, outer side view mirror
position, steering wheel position,
instrument panel illumination
intensity and head-up display
height/brightness will automatical-
ly adjust to the stored positions.
3. "Driver 1(or 2) settings applied"
will appear on the LCD display.
The message appears only for
the driver's seat position memory
setting.
Information
• If you press the SET button or num-
ber 1 button with the number 1 set-
ting in operation, the setting will tem-
porarily deactivate. If you press the
number 2 button, the number 2 set-
ting will activate.
• If you press the number 2 button or
SET button with the number 2 button
in operation, the number 2 setting
will temporarily deactivate. Press the
number 1 button, the number 1 set-
ting will activate.
• If you operate the seat adjustment
switch, side view mirror, steering
wheel, instrument panel illumination
or head-up display while recalling the
stored positions, the pre-set settings
will become ineffective.
Resetting the Seat Position
Memory System
Take the following procedures to
reset the seat position memory sys-
tem, when it does not operate prop-
erly.
To reset the seat position mem-
ory system
1. Stop the vehicle and open the dri-
ver's door with the Engine
Start/Stop button in the ON posi-
tion and the gear shifted to P
(Park).
2. Operate the control switch to set
the driver's seat and seatback to
the foremost position.
3. Simultaneously press the SET
button and push forward the dri-
ver's seat movement switch over 2
seconds.
While resetting the seat posi-
tion memory system
1. It starts with the notification sound.
2. The driver's seat and seatback is
adjusted to the rearward position
with the notification sound.
3. The driver's seat and seatback is
re-adjusted to the default position
(central position) with the notifica-
tion sound.
However, in the following cases, the
resetting procedure and the notifica-
tion sound may stop.
- The memory button is pressed.
- The seat control switch is operated.
- The gear is shifted out of P (Park).
- The driving speed exceeds 2 mph
(3 km/h).
- The driver's door is closed.
i