ECO mode GENESIS G90 2023 Owners Manual

3-56
Safety System
ORS031122
2. Fasten the lap/shoulder belt latch
into the buckle. Listen for the distinct
“click” sound.
Information
Position the release button so that it is easy
to access in case of an emergency.
ORS031125
3. Pull the shoulder portion of the
seat belt all the way out. When the
shoulder portion of the seat belt
is fully extended, it will shift the
retractor to the “Automatic Locking”
(child restraint) mode.
4. Slowly allow the shoulder portion of
the seat belt to retract and listen for
an audible “clicking” or “ratcheting”
sound. This indicates that the retractor
is in the “Automatic Locking” mode.
If no distinct sound is heard, repeat
steps 3 and 4.5. Remove as much slack from the belt
as possible by pushing down on the
child restraint system while feeding
the shoulder belt back into the
retractor.
6. Push and pull on the child restraint
system to confirm that the seat belt
is holding it firmly in place. If it is not,
release the seat belt and repeat steps
2 through 6.
7. Double check that the retractor is in
the “Automatic Locking” mode by
attempting to pull more of the seat
belt out of the retractor. If you cannot,
the retractor is in the “Automatic
Locking” mode.
If your CRS (child restraint system)
manufacturer instructs or recommends
you to use a tether anchor with the lap/
shoulder belt, refer to the previous pages
for more information.
Information
When the seat belt is allowed to retract to
its fully stowed position, the retractor will
automatically switch from the “Automatic
Locking” mode to the emergency lock
mode for normal adult usage.
WARNING
If the retractor is not in the “Automatic
Locking” mode, the child restraint
can move when your vehicle turns or
stops suddenly. A child can be seriously
injured or killed if the child restraint
is not properly anchored in the car,
including manually pulling the seat belt
all the way out to shift the retractor to
the “Automatic Locking” mode.
To remove the child restraint, press the
release button on the buckle and then
pull the lap/shoulder belt out of the
restraint and allow the seat belt to retract
fully.

3-64
Safety System
WARNING
If your SRS malfunctions, the air bag
may not inflate properly during an
accident, increasing the risk of serious
injury or death.
If any of the following conditions occur,
your SRS is malfunctioning:

[The light does not turn on for
approximately three to six seconds
when the Engine Start/Stop button is
in the ON position.

[The light stays on after illuminating
for approximately three to six
seconds.

[The light comes on while the vehicle
is in motion.

[The light blinks when the engine is
running.
Have an authorized retailer of Genesis
Branded products inspect the SRS
as soon as possible if any of these
conditions occur.
During a moderate to severe frontal
collision, sensors will detect the
vehicle’s rapid deceleration. If the rate of
deceleration is high enough, the control
unit will inflate the front air bags, at the
time and with the force needed.
The front air bags help protect the driver
and front passenger by responding to
frontal impacts in which seat belts alone
cannot provide adequate restraint. When
needed, the side air bags help provide
protection in the event of a side impact
or rollover by supporting the side upper
body area.
[Air bags are activated (able to inflate
if necessary) only when the Engine
Start/Stop button is in the ON or
START position and it can be activated
within about 3 minutes after the
engine is turned off.

[Air bags inflate in the event of certain
frontal or side collisions to help
protect the occupants from serious
physical injury.

[There is no single speed at which the
air bags will inflate. Generally, air bags
are designed to inflate based upon the
severity of a collision and its direction.
These two factors determine whether
the sensors produce an electronic
deployment/inflation signal.

[The front air bags will completely
inflate and deflate in an instant. It is
virtually impossible for you to see the
air bags inflate during an accident. It is
much more likely that you will simply
see the deflated air bags hanging out
of their storage compartments after
the collision.

[In addition to inflating in serious side
collisions, vehicles equipped with a
rollover sensor, side and/or curtain air
bags and front center side air bag will
inflate if the sensing system detects a
rollover.
When a rollover is detected, curtain
air bags will remain inflated longer to
help provide protection from ejection,
especially when used in conjunction
with the seat belts.

4-19
04
AUTO STOP indicator light
(if equipped)
This indicator light illuminates:
When the engine enters the Idle Stop
mode of ISG (Idle Stop and Go) system.
This indicator light blinks:
When the engine automatically starts,
the AUTO STOP indicator on the cluster
will blink for 5 seconds.
For more details, refer to "ISG (Idle Stop
and Go) system" section in chapter 6.
Information
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, MDPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean the
system has malfunctioned.
Turn signal indicator light
This indicator light blinks:
When you operate the turn signal
indicator stalk.
If any of the following occur, there may
be a malfunction with the turn signal
system.
-The turn signal indicator light
illuminates but does not blink
-The turn signal indicator light blinks
rapidly
-The turn signal indicator light does not
illuminate at all
If any of these conditions occur, have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
High beam indicator light
This indicator light illuminates:
• When the headlights are on and in the
high beam position
• When the turn signal lever is pulled
into the Flash-to-Pass position.
004_RS4_HMA.indd 4-192022-04-06  3:02:31

4-27
04
ORS042035NORS042035N
Driving Assist, Map and Normal View
modes are displayed in the instrument
cluster.
Normal view is also show in the widget
mode.
Driving Assist view
ORS041026ORS041026
The status of Smart Cruise Control, Lane
Following Assist, Highway Driving Assist,
etc. is displayed when Driving Assist view
is selected.
For more details, refer to each system
information section in chapter 6.
Normal View
In the Normal View, using the (Optical
mouse), you may change through items
in the following order.
ORS042025NORS042025N
Drive info
Trip distance, average fuel economy, and
total driving time are displayed.
The information is combined for each
ignition cycle. However, when the engine
has been OFF for 4 hours or longer the
Drive Info screen will reset.
To manually reset the information, press
the
button three times on the steering
wheel when Drive Info is displayed.
The trip distance, the average fuel
economy, and total driving time will reset
simultaneously.
ORS042029NORS042029N
Since refueling
Trip distance, average fuel economy, and
total driving time after the vehicle has
been refueled are displayed.
To reset manually, press the
button
three times on the steering wheel when
‘Since Refueling’ is displayed.
004_RS4_HMA.indd 4-272022-04-06  3:02:34

4-28
Instrument Cluster, Armrest touchscreen, Infotainment system
ORS042028NORS042028N
Accumulated info
Accumulated trip distance, average fuel
economy, and total driving time are
displayed.
The information is accumulated starting
from the last reset.
To manually reset the information,
press the
button three times on the
steering wheel when Accumulated Info is
displayed. The trip distance, the average
fuel economy, and total driving time will
reset simultaneously.
ORS041031LORS041031L
Auto stop (if equipped)
AUTO STOP display shows the elapsed
time of engine stop by Idle Stop and Go
system.
To manually reset the information, press
the
button three times on the steering
wheel when ‘AUTO STOP’ is displayed.
For more details, refer to “Idle Stop and
Go (ISG)” section in chapter 6.
ORS041032LORS041032L
Tire pressure
The tire pressure of each tire is displayed.
For more details, refer to “Tire Pressure
Monitoring System (TPMS)” section in
chapter 8.
ORS041030LORS041030L
Driving force distribution (if equipped)The distribution status of the driving
power of the front and rear wheels are
displayed when Auto 4WD mode is
activated.
For more details, refer to "Four Wheel
Drive (4WD)" section in chapter 6.
004_RS4_HMA.indd 4-282022-04-06  3:02:34

5-10
Convenience Features
Panic button
Press and hold the Panic button P for
more than one second. The horn sounds
and hazard warning lights blink for about
30 seconds. To cancel the panic mode,
press any button on the Smart Key.
Remotely starting vehicle (if
equipped)
You can start the vehicle using the
Remote Start button Q on the smart key.
To start the vehicle remotely:
1. Press the door lock button on the
smart key within 32 feet (10 m) from
the vehicle.
2. Press the Remote Start button Q for
more than 2 seconds within 4 seconds
after pressing the door lock button.
The hazard warning lights will blink
and the engine will start.
3. To turn off the remote start function,
press the Remote Start button Q
once.
Information

[The vehicle must be in P (Park) for the
remote start function to start.

[The engine turns off if you get in the
vehicle without a registered smart key.

[The engine turns off if you do not get
in the vehicle within 10 minutes after
remotely starting the vehicle.

[The Remote Start button Q may not
operate if the smart key is not within 32
feet (10 m).

[The vehicle will not remotely start if the
engine hood or trunk is opened.

[Do not idle the engine for a long period.

[Do not operate remote start in closed
areas where there is no adequate
ventilation for the engine exhaust.
Remotely moving vehicle forward or
backward (if equipped)
With the smart key, the driver can move
the vehicle forward or backward using
the Forward/Backward button R on the
smart key.
For more details, refer to “Remote Smart
Parking Assist (RSPA)” section in chapter
7.
Start-up
You can start the engine without
inserting the key.
For more details, refer to the “Engine
Start/Stop Button” section in chapter 6.

5-18
Convenience Features
Locking places the digital key (smart
phone)

[Ultra Wide Band unsupported smart
phone
ORS051009
A : Door handle authentication pad
B : NFC antenna (Backside of the smart phone) (The
antenna position differs depending on models.)
- The door will lock or unlock by
touching the registered digital
key (card key) NFC antenna to the
driver’s or passenger’s door handle
authentication pad
A for more than
2 seconds.
- If the Two Press Unlock feature
is set, only the driver’s door pops
out and unlocks when the digital
key (smart phone) is placed on the
driver’s door handle authentication
pad
A. Place the digital key (smart
phone) on the driver’s door handle
authentication pad once more
within 4 seconds to unlock all doors.
[Ultra Wide Band supported smart
phone
- If you touch the door lock/unlock
sensor (engraved part) on the
door handle with the smart phone
in possession, the door locks or
unlocks.
- If you approach the front door
handle with the smart phone
in possession when ‘On driver
approach’ is set, the door unlocks
automatically.

[After unlocking the doors, the doors
will automatically re-lock after 30
seconds unless a door is opened.

[If the smart phone digital key does
not operate, try again after moving
the smart phone away from the door
handle authentication pad (more than
4 in. (0.1 m)).
Information

[You cannot lock your vehicle using the
digital key (smart phone) if any of the
following occurs:
-The smart key is in the vehicle.
-The Engine Start/Stop button is in
WKH$&&RU21SRVLWLRQ
-Any of the doors, hood, or trunk are
open.

[The door may not unlock automatically
if you stay near the vehicle for several
minutes with the Ultra Wide Band
supported smart phone in possession.

[If the smart phone is kept in the back
pocket or bag, it may cause poor
Bluetooth connection, or the door lock/
unlock or vehicle start-up operation my
be delayed.

5-63
05

[Visit the HomeLink website at: www.
homelink.com. Then at the top of the
page, choose your vehicle make. Then
watch the You Tube video, and/or
access additional website information.

[If you choose to access the website
via your cell phone, scan the QR code.

[Or, call HomeLink customer support
at 1-800-355-3515 (Please have the
vehicle make/model AND the opener
device make/model readily available.)
1) Programming Preparation
ORS052306N
1. When programming a garage door
opener, it is advised to park the
vehicle outside of the garage.2. It is recommended that a new battery
be placed in the handheld transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the radio-
frequency signal.
3. Place the ignition switch to the ACC
(Accessory) position for programming
of HomeLink.
 3URJUDPPLQJD1HZ+RPH/LQNp
ORS052307N
1. Press and release the HomeLink
button (1), (2) or (3), you would like
to program. The HomeLink indicator
light (7) will flash orange slowly (if
not, perform the steps of “Erasing
HomeLink Buttons” section, and start
over).
OJX1050295N
2. Position the garage door opener
remote 1 – 3 inches (2 – 8 cm) away
from the HoleLink buttons.

5-74
Convenience Features
Reverse Parking Aid (if equipped)
ORS051044
When the gear is shifted to the R
(Reverse) position, the side view mirror(s)
will rotate downwards to aid with driving
in reverse.
The position of the side view mirror outer
ring M determines whether or not the
mirrors will move:
How it works

[When the outer ring is either in the
left side or right side, both side view
mirrors will move.

[If the outer rings is in the center
position, both side view mirrors will
not move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:

[The Engine Start/Stop button is
pressed to either the OFF position or
the ACC position.

[The gear is shifted to any position
except R (Reverse).
Reverse parking aid user settings
mode
You may change the angle of the side
view mirror if it is difficult to see the side
view with the basic downward mirror
angle provided when reversing.
When the vehicle is first delivered, the
set downward angle of the left and right
side view mirror are different to ensure
driver visibility.
1. Make sure the vehicle is stopped.
2. Depress the brake pedal and shift the
gear to R (Reverse). When the outer
ring is either in the left position or
right position, both side view mirror
angle will move downward to the
basic set position.
3. Rotate the outer ring either to the left
position or right position to select
the side view mirror you would like
to adjust. Then press “
z,
x,
{,
y”
switch to adjust the side view mirror
to the desired angle.
4. After adjusting the angle to save the
adjusted side view mirror angle, shift
the gear to another position other
than R (Reverse), or rotate the outer
ring to the center position.
5. Set the other side view mirror
following the above procedure 1 to 4.
Resetting reverse parking aid user
settings mode
To change the side view mirror angle
back to the basic angle, shift the gear to
R (Reverse), and adjust the mirror angle
higher than when the gear is in P (Park),
N (Neutral) and D (Drive).
Information
When changing the angle of both side
view mirrors, it is recommended to change
the angle one side at a time following the
procedure 1 to 4.

5-125
05
Automatic Temperature Control
Mode
The Automatic Climate Control System
is controlled by setting the desired
temperature.
1. Press the AUTO button.
The mode selection, fan speed,
air intake and air-conditioning will
be controlled automatically by the
temperature setting you select.
(To select the rear seat AUTO from
the front seat, press the icon in the
climate control information screen .)
ORS051144
2. When the climate control system is
being automatically controlled, fan
speed can be selected (Low/Medium/
High).

[High: Use when quick heating or
cooling is preferred.

[Medium: Use when medium fan
speed is preferred for cooling or
heating.

[Low: Use when low fan speed is
preferred for cooling or heating.3. Turn the temperature control knob
to the desired temperature. If the
temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
After the interior has cooled
sufficiently, adjust the knob to
a higher temperature set point
whenever possible.
To turn the automatic operation off,
select any function of the following:

[Front windshield defroster button
(Press the button one more time
to deselect the front windshield
defroster function. The ‘AUTO’
sign will illuminate on the climate
information screen once again.)

[Fan speed control icon
The selected function will be controlled
manually while other functions operate
automatically.
For your convenience and to improve the
efficiency of the climate control, use the
AUTO button and set the temperature to
72°F (22°C).
To change the temperature unit from °C
to °F or °F to °C:
Press the AUTO button for 3 seconds
while pressing the OFF button.