Info GENESIS G90 2023 Owners Manual

5-65
05
3) Two-Way Communication
3URJUDPPLQJ)RUVHOHFWJDUDJHGRRU
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
:D\&RPPXQLFDWLRQIXQFWLRQDOLW\
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
:D\&RPPXQLFDWLRQ3URJUDPPLQJ
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
%XWWRQ

5-66
Convenience Features
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light S is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
S changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.2SHUDWLQJ+RPH/LQN®
 2SHUDWLQJ+RPH/LQNp
ORS052307N
1. Press and release the desired
programmed HomeLink button (M, N
or O).
Information
The HomeLink indicator S should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.

5-68
Convenience Features
3. Erasing HomeLink® Buttons
1) Erasing and Reprogramming a Single
+RPH/LQNp%XWWRQ
1. Press and hold the desired HomeLink
button you want to re-program. DO
NOT release the button.
2. The HomeLink indicator light S will
illuminate solid green. Release the
button as soon as the HomeLink
indicator light S begins to flash
orange, usually about 20 seconds.
3. Proceed with the steps in the
“Programming a New HomeLink
Button” section.
Information
If you do not complete the re-
programming of a new device to the
button, it will revert to the previously
stored programming.
2) The following instructions will erase
$//+RPH/LQNpSURJUDPPLQJIURP
ALL buttons:
ORS052310N
1. Press and hold the buttons M and O
simultaneously.
2. The HomeLink indicator light S will
illuminate solid Orange for about 10
seconds.
3. Release the buttons once the
HomeLink indicator light S changes
to Green and flashes rapidly.
4. Now all three HomeLink buttons
M, N and O are cleared of any
programming.
Information
HomeLink® and the HomeLink® House
logo are registered trademarks of Gentex
&RUSRUDWLRQ
The myQ logo is a registered trademark of
7KH&KDPEHUODLQ*URXS,QF

5-73
05
Folding the rearview mirrors
ORS051043
The rearview mirrors can be folded or
unfolded by pressing the button.
Infotainment system setting

[On door unlock
,I
S6HWXS

5-74
Convenience Features
Reverse Parking Aid (if equipped)
ORS051044
When the gear is shifted to the R
(Reverse) position, the side view mirror(s)
will rotate downwards to aid with driving
in reverse.
The position of the side view mirror outer
ring M determines whether or not the
mirrors will move:
How it works

[When the outer ring is either in the
left side or right side, both side view
mirrors will move.

[If the outer rings is in the center
position, both side view mirrors will
not move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:

[The Engine Start/Stop button is
pressed to either the OFF position or
the ACC position.

[The gear is shifted to any position
except R (Reverse).
Reverse parking aid user settings
mode
You may change the angle of the side
view mirror if it is difficult to see the side
view with the basic downward mirror
angle provided when reversing.
When the vehicle is first delivered, the
set downward angle of the left and right
side view mirror are different to ensure
driver visibility.
1. Make sure the vehicle is stopped.
2. Depress the brake pedal and shift the
gear to R (Reverse). When the outer
ring is either in the left position or
right position, both side view mirror
angle will move downward to the
basic set position.
3. Rotate the outer ring either to the left
position or right position to select
the side view mirror you would like
to adjust. Then press “
z,
x,
{,
y”
switch to adjust the side view mirror
to the desired angle.
4. After adjusting the angle to save the
adjusted side view mirror angle, shift
the gear to another position other
than R (Reverse), or rotate the outer
ring to the center position.
5. Set the other side view mirror
following the above procedure 1 to 4.
Resetting reverse parking aid user
settings mode
To change the side view mirror angle
back to the basic angle, shift the gear to
R (Reverse), and adjust the mirror angle
higher than when the gear is in P (Park),
N (Neutral) and D (Drive).
Information
When changing the angle of both side
view mirrors, it is recommended to change
the angle one side at a time following the
procedure 1 to 4.

5-75
05
ORS052001L
WINDOWS
M Driver’s door power window switch
N Front passenger’s door power window
switch
O Rear door (left) power window switch
P Rear door (right) power window switchQ Window opening and closing
R Automatic power window
S Rear side window sunshades
T Power window lock switch/Electronic
child safety lock
Information
If the rear passenger seat sunshades are equipped, you can fold/unfold the sunshades with
the window switch. For details, see "Rear Side sunshades" in chapter 5.

5-77
05
Automatic reverse
ORS051047
If a window senses any obstacle while it
is closing automatically, it will stop and
lower approximately 12 in. (30 cm) to
allow the object to be cleared.
If the window detects the resistance
while the power window switch is
pulled up continuously, the window
will stop upward movement then lower
approximately 1 in. (2.5 cm).
If the power window switch is pulled
up continuously again within 5 seconds
after the window is lowered by the
automatic window reverse feature,
the automatic window reverse will not
operate.
Information
The automatic reverse feature is only
active when the “Auto Up” feature is used
by fully pulling up the switch to the second
detent.
WARNING
Make sure body parts or other objects
are safely out of the way before closing
the windows to avoid injuries or vehicle
damage.
Objects less than 0.16 in. (4 mm) in
diameter caught between the window
glass and the upper window channel
may not be detected by the automatic
reverse window and the window will
not stop and reverse direction.

5-81
05
Using the rear seat power sunshade
(if equipped)
ORS052051N
2SHUDWLQJUHDUVHDWVXQVKDGHVZLWFK
Press the switch to open the rear seat
power sunshade. Press again to close the
sunshade.
The sunroof will not be opened.
ORS051249L
2SHUDWLQJUHDUVHDWVXQVKDGHIURP
touchscreen
: Stops the rear seat power
sunshade from opening or closing.
: Stops the seat mode and
the rear seat power sunshade from
operating.
1. Press
from the left side menu of
the armrest touchscreen.

[Sunshade adjusting screen is
displayed.
2. Press and slide
in the center of
the display upward or downward to
completely raise or lower the power
sunshade.

[To adjust the power sunshade to the
desired position when the sunshade
is opening or closing, press

on the upper right part of the
touchscreen or press
again.
CAUTION
Do not push or pull the power sunshade
with your hands. The sunshade may be
damaged and cause malfunction.
Information

[Wrinkles formed on the power
sunshade are normal due to material
characteristic.

[While the power sunshade is opened
or being operated, the mood lighting
turns off.

5-84
Convenience Features
Resetting the Sunroof
Front seat power sunshade and
glass
ORS052055N
In some circumstances resetting the
sunroof operation may need to be
performed. Some instances where
resetting the sunroof may be required
include:

[When the 12-volt battery is either
disconnected or discharged

[When the sunroof fuse is replaced

[If the sunroof one-touch AUTO OPEN/
CLOSE operation is not functioning
properlySunroof resetting procedure:
1. It is recommended to perform the
reset procedure with the vehicle
engine running. Start the vehicle in P
(Park).
2. Make sure the power sunshade and
sunroof glass are in the fully closed
position. If the power sunshade
and sunroof glass are open, push
the switch forward until the power
sunshade and sunroof glass are fully
closed.
3. Release the switch when the power
sunshade and sunroof glass are fully
closed.
4. Push the switch forward until the
power sunshade and sunroof glass
move slightly. Then release the switch.
5. Once again push and hold the sunroof
switch forward until the power
sunshade and sunroof glass slide
open and close.

[Do not release the switch until the
operation is completed.
If you release the switch during
operation, start the procedure again
from step 2.
Information
If the sunroof is not reset when the vehicle
battery is disconnected or discharged, or
the sunroof fuse is blown, the sunroof may
not operate normally.

5-88
Convenience Features
Information

[In cold and wet climates, the outside
power trunk open button may not work
properly due to freezing conditions. If
this occurs, remove the ice before using
the outside power trunk open/close
button or use the power trunk open/
close button on the smart key or the
instrument panel.

[If you leave the smart key in the trunk
and close the trunk, a warning will
sound for about 5 seconds. If this
occurs, open the trunk by pressing the
power trunk open button on the outside
of the trunk.

[If there are obstacles such as snow
on the trunk, the trunk may not open
automatically. After removing the
obstacle, try to open it again.

[Be careful where there is an incline, as
the trunk lid may drop slightly when it
is stopped before it fully opens.
Operating the Power Trunk
Power trunk open button (Smart
key)
ORS051059
When the trunk is closed, press the
power trunk open button for 1 second.
The trunk will open with a warning
sound.
While the trunk is opening, press the
button to stop power trunk operation.