check engine GENESIS G90 2023 User Guide
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G90, Model: GENESIS G90 2023Pages: 676, PDF Size: 14.16 MB
Page 195 of 676
5-54
Convenience Features
The Smart Posture Care system
automatically provides a healthy posture
(position) for the driver’s back, and sets
the steering wheel, side view mirrors,
head-up display positions according to
the driver’s body measurements.
Information
, I W K H 6 H D W 3 R V W X U H & D U H V \ V W H P G R H V Q R W
operate normally, have the system checked
by an authorized retailer of Genesis
Branded products.
OJWEV051211N
1. Check that the gear is in P (Park) while
the Engine Start/Stop button is in the
ON position.
2. 6 H O H F W S 6 H W X S
Page 196 of 676
5-55
05
Motor Driven Power Steering
(MDPS)
The system assists you with steering the
vehicle. If the vehicle is turned off or
if the power steering system becomes
inoperative, you may still steer the
vehicle, but it will require increased
steering effort.
Should you notice any change in the
effort required to steer during normal
vehicle operation, have the system
checked by an authorized retailer of
Genesis Branded products.
CAUTION
If Motor Driven Power Steering does not
operate normally, the warning light
and the message ‘Check motor driven
power steering’ will illuminate on the
instrument cluster. You may steer the
vehicle, but it will require increased
steering efforts. Take the vehicle to an
authorized retailer of Genesis Branded
products and have the system checked
as soon as possible.
Information
The following symptoms may occur during
normal vehicle operation:
[ The steering effort may be high
immediately after pressing the Engine
6 W D U W 6 W R S E X W W R Q W R W K H 2 1 S R V L W L R Q
This happens as the system performs
the MDPS system diagnostics. When
the diagnostics are completed, the
steering wheel effort will return to its
normal condition.
[ When the battery voltage is low, you
might have to put more steering effort.
However, it is a temporary condition so
that it will return to normal condition
after charging the battery.
[ A click noise may be heard from the
MDPS relay after the Engine Start/Stop
E X W W R Q L V L Q W K H 2 1 R U 2 ) ) S R V L W L R Q
[ Motor noise may be heard when the
vehicle is at a stop or at a low driving
speed.
[ When you operate the steering wheel
in low temperatures, abnormal noise
may occur. If the temperature rises, the
noise will disappear. This is a normal
condition.
[ When an error is detected from MDPS,
the steering effort assist function will
not be activated in order to prevent
fatal accidents. Instrument cluster
warning lights may be on or the
steering effort may be high. If these
symptoms occur, drive the vehicle to
a safe area as soon as it is safe to do
so. Have the system checked by an
authorized retailer of Genesis Branded
products as soon as possible.
STEERING WHEEL
Page 201 of 676
5-60
Convenience Features
NOTICE
When using snow chains, be sure to
turn off the Rear Wheel Steering by
selecting ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system to protect the vehicle.
After removing the snow chain,
deselect ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system. If it is not deselected, Rear
: K H H O 6 W H H U L Q J Z L O O Q R W R S H U D W H ) R U
more details on setting the menu, refer
to “Winter Tire” section in Chapter 6.
CAUTION
[ If there is a problem with the Rear
Wheel Steering system, a warning
light and warning message appears
on the instrument cluster and
Rear Wheel Steering system stops
working. If the warning light and
warning message are still displayed
even when the vehicle is stopped
and the engine is restarted, have the
vehicle checked by an authorized
retailer of Genesis Branded products.
[ If the Rear Wheel Steering system
operation is stopped while the rear
wheels are not straight, the vehicle
may lean to one side while driving.
Information
With no warning light on the instrument
cluster, the following conditions are
normal:
[ Immediately after starting the engine,
Rear Wheel Steering system performs
diagnostics and operates normally after
about 2 seconds.
[ When turning the engine on or off,
Rear Wheel Steering system can
operate for about 2 seconds even
though the steering wheel is not steered
to check system condition.
[ Motor noise may be heard when you
steer the vehicle while stopping or
driving at low speed.
[ In driving conditions in which the rear
wheels are steered in the same direction
as the front wheels when (
) is on
the instrument cluster by pressing the
Lane Following Assist button on the
steering wheel or Highway Driving
Assist function is activated, keep the
rear wheels straight to improve Lane
Keeping Assist performance.
[ , I
Page 227 of 676
5-86
Convenience Features
Opening the Hood
ORS051056
1. Park the vehicle and set the parking
brake.
2. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
ORS051057
3. Go to the front of the vehicle, raise the
hood slightly, push up the secondary
latch M inside of the hood center and
lift the hood N.
After the hood has been lifted halfway,
it will raise completely by itself.
Closing the Hood
1. Before closing the hood, check in and
around the engine compartment to
ensure the following:
- Any tools or other loose objects
are removed from the engine
compartment area or hood
opening area
- All glove, rags, or other
combustible material is removed
from the engine compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
approximately 12 in. (30 cm) from the
closed position) and push down to
securely lock in place. Then double
check to be sure the hood is secure.
If the hood can be raised slightly, it is
not securely locked. Open it again and
close it with more force.
WARNING
[ Before closing the hood, ensure
all obstructions are removed from
around the hood opening.
[ Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.
[ Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.
HOOD
Page 238 of 676
5-97
05
WARNING
Automotive fuel is highly flammable
D Q G H [ S O R V L Y H ) D L O X U H W R I R O O R Z W K H V H
guidelines may result in SERIOUS
INJURY or DEATH:
[ Read and follow all warnings posted
at the gas station.
[ Before refueling, note the location
R I W K H ( P H U J H Q F \ ) X H O 6 K X W 2 I I L I
available, at the gas station.
[ Before touching the fuel nozzle, you
should eliminate the potential build-
up of static electricity by touching
a metal part of the vehicle, a safe
distance away from the fuel filler
neck, nozzle, or other gas source,
with your bare hand.
[ Do not use mobile phones while
refueling. Electric current and/or
electronic interference from cellular
phones can potentially ignite fuel
vapors and cause a fire.
[ Do not get back into a vehicle
once you have begun refueling.
You can generate a buildup of
static electricity by touching,
rubbing or sliding against any item
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapors
causing a fire. If you must re-enter
the vehicle, you should once again
eliminate potentially dangerous
static electricity discharge by
touching a metal part of the vehicle,
away from the fuel filler neck, nozzle
or other fuel source, with your bare
hand.[ When using an approved portable
fuel container, be sure to place the
container on the ground prior to
refueling. Static electricity discharge
from the container can ignite fuel
vapors causing a fire.
Once refueling has begun, contact
between your bare hand and the
vehicle should be maintained until
the filling is complete.
[ Use only approved portable plastic
fuel containers designed to carry and
store fuel.
[ When refueling, always shift the
gear to the P (Park) position, set
the parking brake, and press the
Engine Start/Stop button to the
2 ) ) S R V L W L R Q 6 S D U N V S U R G X F H G E \
electrical components related to the
engine can ignite fuel vapors causing
a fire.
[ Do not use matches or a lighter and
do not smoke or leave a lit cigarette
in your vehicle while at a gas station,
especially during refueling.
[ Do not over-fill or top-off your
vehicle tank, which can cause fuel
spillage.
[ If a fire breaks out during refueling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
W K H O R F D O I L U H G H S D U W P H Q W ) R O O R Z D Q \
safety instructions they provide.
[ If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.
[ Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
Page 243 of 676
5-102
Convenience Features
Updating Software
ORS052314N
You can see the progress of the update
on the screen.
After the update is complete, you will
receive a notification on your phone
or the vehicle screen that the software
update is complete.
Information
The screen turns off automatically after 3
minutes to save the battery. If the screen
turns off automatically, you can check the
update progress by pressing the Engine
Start/Stop button.
Information
[ After the update starts, you can exit the
vehicle.
[ 7 K H 2 Y H U 7 K H $ L U V R I W Z D U H X S G D W H
feature is only available for Active and
( Q U R O O H G * H Q H V L V & R Q Q H F W H G 6 H U Y L F H V
users.
[ The update details may vary, for details
you can visit the What’s New link.
[ & K H F N W K H Q R W L F H I R U W K H 2 Y H U 7 K H $ L U
software update on mygenesis.com
[ , I W K H X S G D W H I D L O V W K H ( & 8 Z L O O
attempt to recovery itself automatically
(rollback). If you want to retry the
software update, even after a successful
U H F R Y H U \ F R Q W D F W * H Q H V L V & X V W R P H U
& D U H
[ If the update or recovery fails, contact
* H Q H V L V & X V W R P H U & D U H
[ After the update is complete, it
may provide new functions or
improvements. For more information,
V H H W K H
Page 259 of 676
5-118
Convenience Features
ORS051284
) U R Q W : L Q G V K L H O G : L S H U V
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS
Page 283 of 676
5-142
Convenience Features
WARNING
Windshield heating
Do not use the
position during
cooling operation in extremely humid
weather. The difference between the
temperature of the outside air and that
of the windshield could cause the outer
surface of the windshield to fog up,
causing loss of visibility could cause
an accident resulting in serious injury
or death. In this case, set the mode
selection button to the
position
and fan speed control knob to a lower
speed.
[ For maximum defrost performance,
set the temperature control to the
highest temperature setting and
the fan speed control to the highest
setting.
[ If warm air to the floor is desired while
defrosting or defogging, set the mode
to the floor-defrost position.
[ Before driving, clear all snow and ice
from the windshield, rear window,
side view mirrors and all side
windows.
[ Clear all snow and ice from the
hood and air inlet in the cowl grill
to improve heater and defroster
efficiency and to reduce the
probability of fogging up the inside of
the windshield.
NOTICE
If the engine temperature is still cold
after starting, then a brief engine warm
up period may be required for the
vented air flow to become warm or hot.
To Defog Inside Windshield
ORS051131L
1. Select the desired fan speed.
2. Select the desired temperature.
3. Press the defroster button (
).
4. Fresh mode will be selected
automatically.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, press the
button once to enable Fresh mode
(indicator light OFF).
If the
position is selected, the fan
speed is automatically increased.
: , 1 ' 6 + , ( / ' ' ( ) 5 2 6 7 , 1 * $ 1 ' ' ( ) 2 * * , 1 *
Page 284 of 676
5-143
05
To Defrost Inside Windshield
ORS051130
1. Set the fan speed to the highest
(extreme right) position.
2. Set the temperature to the extreme
hot (HI) position.
3. Press the defroster button (
).
4. Fresh mode will be selected
automatically.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, press the
button once to enable Fresh mode
(indicator light OFF).
If the
position is selected, lower fan
speed is adjusted to a higher fan speed.
Defogging Logic
To reduce the probability of fogging
up the inside of the windshield, the air
intake or air conditioning are controlled
automatically according to certain
conditions. To cancel or reset the
defogging logic, do the following.
1. Press the Engine Start/Stop button to
the ON position.
2. Press the defroster button (
) or
().
3. While pressing the air conditioning
button (A/C), press the air intake
control button at least 5 times within
3 seconds.
The air intake control button indicator
will blink 3 times to indicate that the
defogging logic has been disabled.
Repeat the steps again to re-enable the
defogging logic.
If the battery has been discharged or
disconnected, it resets to the defog logic
status.
Page 287 of 676
5-146
Convenience Features
Turning the Auto Defogging System
ON or OFF
& O L P D W H F R Q W U R O V \ V W H P
Press the front windshield defroster
button for 3 seconds when the Engine
Start/Stop button is in the ON to turn the
system on or off.
To check whether the system is on
or off, go to the settings menu in the
infotainment system and see if 'Auto
Defog' is selected or not.
Infotainment system
Auto Defogging System can be turned
R Q D Q G R I I E \ V H O H F W L Q J S 6 H W X S