display GENESIS G90 2023 Service Manual

5-60
Convenience Features
NOTICE
When using snow chains, be sure to
turn off the Rear Wheel Steering by
selecting ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system to protect the vehicle.
After removing the snow chain,
deselect ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system. If it is not deselected, Rear
:KHHO6WHHULQJZLOOQRWRSHUDWH)RU
more details on setting the menu, refer
to “Winter Tire” section in Chapter 6.
CAUTION

[If there is a problem with the Rear
Wheel Steering system, a warning
light and warning message appears
on the instrument cluster and
Rear Wheel Steering system stops
working. If the warning light and
warning message are still displayed
even when the vehicle is stopped
and the engine is restarted, have the
vehicle checked by an authorized
retailer of Genesis Branded products.

[If the Rear Wheel Steering system
operation is stopped while the rear
wheels are not straight, the vehicle
may lean to one side while driving.
Information
With no warning light on the instrument
cluster, the following conditions are
normal:

[Immediately after starting the engine,
Rear Wheel Steering system performs
diagnostics and operates normally after
about 2 seconds.

[When turning the engine on or off,
Rear Wheel Steering system can
operate for about 2 seconds even
though the steering wheel is not steered
to check system condition.

[Motor noise may be heard when you
steer the vehicle while stopping or
driving at low speed.

[In driving conditions in which the rear
wheels are steered in the same direction
as the front wheels when (
) is on
the instrument cluster by pressing the
Lane Following Assist button on the
steering wheel or Highway Driving
Assist function is activated, keep the
rear wheels straight to improve Lane
Keeping Assist performance.

[,I

5-65
05
3) Two-Way Communication
3URJUDPPLQJ)RUVHOHFWJDUDJHGRRU
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
:D\&RPPXQLFDWLRQIXQFWLRQDOLW\
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
:D\&RPPXQLFDWLRQ3URJUDPPLQJ
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
%XWWRQ

5-67
05
2) Two-Way Communication Display
Behavior
OJWEV051283N
1. Press and release one of the
programmed HomeLink buttons (M,
N or O).
ORS052309N
2. The indicator P and R operates as
below, if your garage door opener
has Two-Way Communication
functionality.
[If the indicator P flashes in Orange,
it indicates that the garage door is
“Closing”.

[The indicator P turns solid green once
the garage door has closed.

[If the indicator R flashes in Orange,
it indicates that the garage door is
“Opening”.

[The indicator R turns solid green once
the garage door has fully opened.

[If the indicator P or R does not
turn to green, it indicates that the
last status of garage door was not
received properly. The HomeLink
mirror tries to receive the last known
status of the garage door for a few
seconds.
3) Recalling Garage Door Status
HomeLink mirror with Two-Way
Communication provides a way to view
the last stored message from the garage
door opener. In order to recall the last
known status of the last activated device,
press the buttons “1 and 2” OR “2 and 3”
simultaneously.

[If the indicator P appears solid Green,
it indicates that the last activated
device was “closed” properly.

[If the indicator R appears solid Green,
it indicates that the last activated
device was “open” properly.

5-81
05
Using the rear seat power sunshade
(if equipped)
ORS052051N
2SHUDWLQJUHDUVHDWVXQVKDGHVZLWFK
Press the switch to open the rear seat
power sunshade. Press again to close the
sunshade.
The sunroof will not be opened.
ORS051249L
2SHUDWLQJUHDUVHDWVXQVKDGHIURP
touchscreen
: Stops the rear seat power
sunshade from opening or closing.
: Stops the seat mode and
the rear seat power sunshade from
operating.
1. Press
from the left side menu of
the armrest touchscreen.

[Sunshade adjusting screen is
displayed.
2. Press and slide
in the center of
the display upward or downward to
completely raise or lower the power
sunshade.

[To adjust the power sunshade to the
desired position when the sunshade
is opening or closing, press

on the upper right part of the
touchscreen or press
again.
CAUTION
Do not push or pull the power sunshade
with your hands. The sunshade may be
damaged and cause malfunction.
Information

[Wrinkles formed on the power
sunshade are normal due to material
characteristic.

[While the power sunshade is opened
or being operated, the mood lighting
turns off.

5-85
05
Rear Seat Power Sunshade
ORS052051N
Reset the rear seat power sunshade in
the following situations.

[When the 12-volt battery is either
disconnected or discharged.

[When the rear seat power sunshade is
not working properly.
1. It is recommended to perform the
reset procedure with the vehicle
engine running. Start the vehicle in P
(Park).
2. Press and hold the switch until the
rear seat power sunshade is fully
closed.
3. Hold the switch until the rear seat
power sunshade slightly moves.
Release the switch until the sunshade
moves slightly.
4. Press and hold the switch again until
the power sunshade is opened then
closed.

[Do not release the switch until
the rear seat sunshade completes
opening/closing. If you release the
switch during operation, start the
procedure again from step 2.
CAUTION
The rear seat power sunshade may not
work properly if it is not reset.
Sunroof Open Warning
ORS041022
If the driver turns off the engine when
the sunroof is not fully closed, the
warning chime will sound for several
seconds and the sunroof open warning
will appear on the cluster LCD display.
Close the sunroof securely when leaving
your vehicle.
CAUTION
Make sure the sunroof is closed fully
when leaving your vehicle. If the
sunroof is left open, rain or snow may
wet the interior of the vehicle. Also,
leaving the sunroof open when the
vehicle is unattended may invite theft.

5-86
Convenience Features
Opening the Hood
ORS051056
1. Park the vehicle and set the parking
brake.
2. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
ORS051057
3. Go to the front of the vehicle, raise the
hood slightly, push up the secondary
latch M inside of the hood center and
lift the hood N.
After the hood has been lifted halfway,
it will raise completely by itself.
Closing the Hood
1. Before closing the hood, check in and
around the engine compartment to
ensure the following:
- Any tools or other loose objects
are removed from the engine
compartment area or hood
opening area
- All glove, rags, or other
combustible material is removed
from the engine compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
approximately 12 in. (30 cm) from the
closed position) and push down to
securely lock in place. Then double
check to be sure the hood is secure.
If the hood can be raised slightly, it is
not securely locked. Open it again and
close it with more force.
WARNING

[Before closing the hood, ensure
all obstructions are removed from
around the hood opening.

[Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.

[Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.
HOOD

5-99
05
ORS052224N
The Head-Up Display is an optional
feature that allows the driver to view
information projected onto a transparent
screen while still keeping your eyes
safely on the road ahead while driving.
Head-up Display Settings
ORS051237L

[Head-up display can be enabled from
the Settings menu in the infotainment
system screen. Select:
-6HWXS

5-100
Convenience Features
Precautions While Using the
Head-up Display

[It may sometimes be difficult to read
information on the head-up display in
the following situations.
- The driver is improperly positioned
in the driver’s seat.
- The driver wears polarizing-filter
sunglasses.
- An object is located above the
head-up display cover
- The vehicle is driven on a wet road.
- Any improper lighting accessory is
installed inside the vehicle, or there
is incoming light from outside of the
vehicle.
- The driver wears glasses.
- The driver wears contact lenses.
When it is difficult to read the head up
display information, adjust the image
height or brightness level from the
Settings menu in the infotainment
system screen.
[For your safety, make sure to stop the
vehicle before adjusting the settings.

[Do not tint the front windshield glass
or add other types of metallic coating.
Otherwise, the head-up display image
may be invisible.

[Do not place any accessories on the
crash pad or attach any objects on the
windshield glass.

[When replacing the front windshield
glass, replace it with a windshield
glass designed for head-up display
operation. Otherwise, duplicated
images may be displayed on the
windshield glass.
WARNING
The warning information of Blind-Spot
Safety on the head-up display are
supplemental. Do not solely depend on
them to change lanes. Always take a
look around before changing lanes.
Information
Head-up Display includes GPL, LGPL,
MPL and other open source license
softwares. All license notices including
related source code are provided at http://
www.mobis.co.kr/opensource/list.do.
If the driver requests on-board
VRIWZDUHRSHQVRXUFHFRGHYLD02%,6B
266UHTXHVW#PRELVFRNUZLWKLQ\HDUV
DIWHUEX\LQJWKLVSURGXFWD&'520RU
other storage device will be sent with the
minimum cost covering storage device cost
and delivery cost.

5-116
Convenience Features
High Beam Assist Operation
Display and control

[After selecting ‘High Beam Assist’
in the Settings menu, High Beam
Assist will operate by following the
procedure below.
- Place the headlight switch in
the AUTO position and push
the headlight lever towards the
instrument cluster. The High Beam
Assist (
) indicator light will
illuminate on the cluster and High
Beam Assist will be enabled.
- When High Beam Assist is enabled,
high beam will turn on when vehicle
speed is above 25 mph (40 km/h).
When vehicle speed is below 15
mph (25 km/h), high beam will turn
off.
- The High Beam (
) indicator light
will illuminate on the cluster when
high beam is on.

[When High Beam Assist is operating,
if the headlight lever or switch is used,
High Beam Assist operates as follow:
- If the headlight lever is pulled
towards you when the high beam
is off, the high beam will turn
on without High Beam Assist
cancelled. When you let go of the
headlight lever, the lever will move
to the middle and the high beam
will turn off.
- If the headlight lever is pulled
towards you when the high beam is
on by High Beam Assist, low beam
will turn on and High Beam Assist
will turn off.
- If the headlight switch is placed
from AUTO to another position
(headlight/position/off), High
Beam Assist will turn off and the
corresponding lamp will turn on.
[When High Beam Assist is operating,
high beam switches to low beam if
any of the following conditions occur:
- When the headlight of an oncoming
vehicle is detected.
- When the tail lamp of a vehicle in
front is detected.
- When the headlight or tail lamp of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light
is bright enough that high beams
are not required.
- When streetlights or other lights are
detected.
Information
The images and colors in the instrument
may differ depending on the instrument
type or theme selected from the
instrument.

5-135
05
ORS051124
ORS051139L
A : Front seat,
B : Rear seat
Press from the climate control
information screen or armrest
touchscreen to select the desired
fragrance intensity.

[Intensity can be selected among
Strong, Medium and Light. Pressing
the button each time will change
the intensity in the order of Strong,
Medium, Light and Off.

[The fragrance cannot be selected with
the button. Fragrance can only be
selected from the settings menu.
ORS051244
How to replace cartridges
1. Turn the engine off, and open the
glove box.
2. Press the upper part of the diffuser
tray.
3. Replace the cartridge.
Information

[For smooth operation of diffuser, it is
recommended to install 2 cartridges.

[If the cartridge is empty or diffuser
replacement alarm is displayed, replace
with a new cartridge.

[The built-in diffuser may not work if
the cartridge is not installed properly.
&KHFNZKHWKHUWKHFDUWULGJHLVLQVWDOOHG
properly.