wheel GENESIS G90 2023 Repair Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G90, Model: GENESIS G90 2023Pages: 676, PDF Size: 14.16 MB
Page 382 of 676
6-72
Driving Your Vehicle
NOTICE
If you drive without disabling the
Rear Wheel Steering system in the
infotainment system after installing
snow chains, the snow chains can
damage your vehicle’s body or chassis
parts. When you hear the snow chain
hitting the vehicle, stop the vehicle and
check whether the snow chains are
installed properly and whether the Rear
Wheel Steering system is disabled.
Information
[ Install AutoSock® (fabric snow chain)
only in pairs and on the rear tires.
It should be noted that installing
AutoSock (fabric snow chain) on the
tires will provide a greater driving
force, but will not prevent side skids.
[ Do not install studded tires without
first checking local, state and municipal
regulations for possible restrictions
against their use.
Chain Installation
When installing AutoSock® (fabric
snow chain), follow the manufacturer's
instructions and mount them as tightly
as possible. Drive slowly (less than 20
mph (30 km/h)) with AutoSock® installed.
If you hear the fabric snow chains
contacting the body or chassis, stop and
tighten them. If they still make contact,
slow down until the noise stops. Remove
the AutoSock® as soon as you begin
driving on cleared roads.
When mounting AutoSock®, park the
vehicle on level ground away from traffic.
Turn on the vehicle Hazard Warning
Flasher and place a triangular emergency
warning device behind the vehicle (if
available).
Always place the vehicle in P (Park),
apply the parking brake and turn off the
engine before installing tire chains.
NOTICE
When using AutoSock® (fabric snow
chain):
[ Wrong size fabric snow chains or
improperly installed fabric snow
chains can damage your vehicle's
brake lines, suspension, body and
wheels.
[ If you hear noise caused by fabric
snow chains contacting the body,
retighten the fabric snow chains to
prevent contact with the vehicle
body.
[ To prevent body damage, retighten
the fabric snow chains after driving
0.3~0.6 miles (0.5~1.0 km).
Page 383 of 676
6-73
06
Winter Precautions
Use high quality ethylene glycol coolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because it
helps prevent corrosion in the cooling
system, lubricates the water pump and
prevents freezing. Be sure to replace or
replenish your coolant in accordance
with the maintenance schedule in
chapter 9. Before winter, have your
coolant tested to assure that its freezing
point is sufficient for the temperatures
anticipated during the winter.
Check battery and cables
Winter temperatures affect battery
performance. Inspect the battery and
cables, as specified in chapter 9. The
battery charging level can be checked by
an authorized retailer of Genesis Branded
products or in a service station.
Change to “winter weight” oil if
necessary
In some regions during winter, it is
recommended to use the “winter
weight” oil with lower viscosity. In
addition, replace the engine oil and filter
if it is close to the next maintenance
interval. Fresh engine oil ensures
optimum engine operation during the
winter months. For further information,
refer to chapter 2. When you are not sure
about a type of winter weight oil, consult
an authorized retailer of Genesis Branded
products.Check spark plugs and ignition system
Inspect the spark plugs, as specified in
chapter 9. If necessary, replace them.
Also check all ignition wirings and
components for any cracks, wear-out,
and damage.
To prevent locks from freezing
To prevent the locks from being frozen,
spray approved de-icing fluid or glycerin
into key holes. When a lock opening is
already covered with ice, spray approved
de-icing fluid over the ice to remove it.
When an internal part of a lock freezes,
try to thaw it with a heated key. Carefully
use the heated key to avoid an injury.
Use approved window washer anti-
freeze solution in system
To prevent the window washer from
being frozen, add authorized window
washer anti-freeze solution, as specified
on the window washer container.
Window washer anti-freeze solution is
available from an authorized retailer of
Genesis Branded products, and most
vehicle accessory outlets. Do not use
engine coolant or other types of anti-
freeze solution, to prevent any damage
to the vehicle paint.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when there
is an accumulation of snow or ice around
or near the rear brakes or if the brakes
are wet. When there is the risk that your
parking brake may freeze, temporarily
apply it with the gear in P (Park). Also,
block the rear wheels in advance, so the
vehicle may not roll. Then, release the
parking brake.
Page 384 of 676
6-74
Driving Your Vehicle
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, you should check underneath
the vehicle on a regular basis, to ensure
that the front wheels and the steering
components is unblocked.
Carry emergency equipment
In accordance with weather conditions,
you should carry appropriate emergency
equipment, while driving. Some of the
items you may want to carry include tire
chains, tow straps or chains, flashlight,
emergency flares, sand, shovel, jumper
cables, window scraper, gloves, ground
cloth, coveralls, blanket, etc.
Do not place objects or materials in the
engine compartment
Putting objects or materials in the engine
compartment may cause an engine
failure or combustion, because they may
block the engine cooling. Such damage
will not be covered by the manufacturer’s
warranty.
Drive your vehicle when water vapor
condenses and accumulates inside the
exhaust pipes
When the vehicle is stopped for a
long time in winter while the engine is
running, water vapor may condense and
accumulate inside the exhaust pipes.
Water in the exhaust pipes may cause
noise, etc., but it is drained driving at
medium to high speed.
Page 391 of 676
7-2
Driver Assistance System
ORS071083
Forward Collision-Avoidance Assist is
designed to help detect and monitor the
vehicle ahead or help detect a powered
two-wheeler, pedestrian or cyclist in
the roadway and warn the driver that
a collision is imminent with a warning
message and warning and application of
emergency braking.
In addition, when driving at high speeds,
Forward Collision-Avoidance Assist
will help detect vehicles in front and
adjacent lanes. If a collision is imminent
when changing lanes, Forward Collision-
Avoidance Assist will apply emergency
braking to help prevent a collision.Junction Turning functionORS071055
Junction Turning function can help avoid
a collision with an oncoming vehicle in
an adjacent lane when turning left at
a crossroad with the turn signal on by
applying emergency braking.
Junction Crossing function
ORS071056
Junction Crossing function can help
avoid a collision with oncoming vehicles
on the left or right side when crossing
an intersection by applying emergency
braking.
) 2 5 : $ 5 ' & 2 / / , 6 , 2 1
Page 397 of 676
7-8
Driver Assistance System
CAUTION
[ The setting of the Warning Timing
D Q G : D U Q L Q J 9 R O X P H D S S O L H V W R
all functions of Forward Collision-
$ Y R L G D Q F H $ V V L V W
[ ( Y H Q W K R X J K S 6 W D Q G D U GT L V V H O H F W H G
I R U : D U Q L Q J 7 L P L Q J L I D G H W H F W H G
Y H K L F O H L Q I U R Q W V X G G H Q O \ V W R S V W K H
Z D U Q L Q J P D \ V H H P O D W H
[ 6 H O H F W S / D W HT I R U : D U Q L Q J 7 L P L Q J
Z K H Q W U D I I L F L V O L J K W D Q G Z K H Q G U L Y L Q J
V S H H G L V V O R Z
) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
Assist operation
Basic function
The basic function for Forward Collision-
Avoidance Assist is to warn and help
control the vehicle depending on the
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’.
ORS071096L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the instrument cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ If a vehicle or powered two-wheeler
is detected in front, the function will
operate when your vehicle speed is
between approximately 6-124 mph
(10-200 km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6-53 mph (10-85 km/h).
Page 398 of 676
7-9
07
ORS071097L
Emergency Braking
To warn the driver that emergency
braking will be assisted, the ‘Emergency
Braking’ warning message will appear
on the instrument cluster, an audible
warning will sound and the steering
wheel will vibrate.
Emergency braking will operate under
the following conditions.
[ Vehicle or powered two-wheeler:
' U L Y L Q J Y H K L F O HStopped
Y H K L F O H
Weak
braking
powerApproximately 6-125 mph
(10-200 km/h)*
Strong
braking
powerApproximately
6-81 mph
(10-130 km/h)*Approximately
6-47 mph
(10-75 km/h)
(6-62 mph
(10-100 km/h))*
*: If Forward Collision-Avoidance Assist judges that
avoiding a collision is difficult even by changing
the driving lane. The function operate range may
decrease due to surroundings of the vehicle. (if
equipped)
[ Pedestrian or cyclist:
The function will operate when
your vehicle speed is between
approximately 6-40 mph (10-65
km/h).
ORS071102L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the instrument cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Page 399 of 676
7-10
Driver Assistance System
Junction Turning function
Junction Turning function will warn and
control the vehicle depending on the
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’.
ORS071098L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the instrument cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the oncoming vehicle or powered
two-wheeler speed is between
approximately 19-44 mph (30-70
km/h).
ORS071099L
Emergency Braking
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the
instrument cluster, an audible warning
will sound and the steering wheel will
vibrate.
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the oncoming vehicle.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the oncoming vehicle or powered
two-wheeler speed is between
approximately 19-44 mph (30-70
km/h).
Page 400 of 676
7-11
07
ORS071102L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the instrument cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Junction Crossing function
Junction Crossing function will warn
and control the vehicle depending on
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’
ORS071100LORS071282L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the instrument cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-34 mph (10-55 km/h)
and the crossing vehicle speed is
between approximately 6-37 mph (10-
60 km/h)
Page 401 of 676
7-12
Driver Assistance System
ORS071103LORS071101L
Emergency Braking
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the
instrument cluster, an audible warning
will sound and the steering wheel will
vibrate.
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the crossing vehicle.
[ The function will operate when
your vehicle speed is between
approximately 6-34 mph (10-55 km/h)
and the crossing vehicle speed is
between approximately 6-25 mph (10-
40 km/h).
ORS071102L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the instrument cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
CAUTION
If the collision angle with the crossing
Y H K L F O H L V E H \ R Q G D F H U W D L Q U D Q J H
Junction Crossing function warning and
F R Q W U R O P D \ E H O D W H R U P D \ Q R W R S H U D W H
Page 402 of 676
7-13
07
Direct Oncoming function
Direct Oncoming function will warn
and control the vehicle depending
on the collision risk level: ‘Collision
Warning’,‘Emergency Braking’ and
‘Stopping vehicle and ending brake
control’.
ORS071096L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the instrument cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-80 mph (10-130
km/h) and the detected oncoming
vehicle speed is approximately above
6 mph (10 km/h) and the oncoming
motorcycle speed is approximately
above 16 mph (25 km/h).
ORS071097L
Emergency Braking
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the
instrument cluster, an audible warning
will sound and the steering wheel will
vibrate.
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the oncoming vehicle.
[ The function will operate when
your vehicle speed is between
approximately 19-80 mph (30-130
km/h) and the detected oncoming
vehicle speed is approximately above
6 mph (10 km/h).