wheel GENESIS GV60 2023 Repair Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: GV60, Model: GENESIS GV60 2023Pages: 690, PDF Size: 14.07 MB
Page 400 of 690
6-66
Driving Your Vehicle
Winter Precautions
Check battery and cables
Winter temperatures affect battery
performance. Inspect the battery and
cables, as specified in chapter 9. Have
the battery charging level be checked by
an authorized retailer of Genesis Branded
products or in a service station.
To prevent locks from freezing
To prevent the locks from being frozen,
spray approved de-icing fluid or glycerin
into key holes. When a lock opening is
already covered with ice, spray approved
de-icing fluid over the ice to remove it.
When an internal part of a lock freezes,
try to thaw it with a heated key. Carefully
use the heated key to avoid an injury.
Use approved window washer anti-
freeze solution in system
To prevent the window washer from
being frozen, add authorized window
washer anti-freeze solution, as specified
on the window washer container.
Window washer anti-freeze solution is
available from an authorized retailer of
Genesis Branded products, and most
vehicle accessory outlets. Do not use
coolant or other types of anti-freeze
solution, to prevent any damage to the
vehicle paint.Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when there
is an accumulation of snow or ice around
or near the rear brakes or if the brakes
are wet. When there is the risk that your
parking brake may freeze, temporarily
apply it with the gear in P (Park). Also,
block the rear wheels in advance, so the
vehicle may not roll. Then, release the
parking brake.
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, you should check underneath
the vehicle on a regular basis, to ensure
that the front wheels and the steering
components is unblocked.
Carry emergency equipment
In accordance with weather conditions,
you should carry appropriate emergency
equipment, while driving. Some of the
items you may want to carry include tire
chains, tow straps or chains, flashlight,
emergency flares, sand, shovel, jumper
cables, window scraper, gloves, ground
cloth, coveralls, blanket, etc.
Do not place objects or materials in the
motor compartment
Putting objects or materials in the motor
compartment may cause an motor
failure. Such damage will not be covered
by the manufacturer’s warranty.
Page 401 of 690
6-67
06
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when there
is an accumulation of snow or ice around
or near the rear brakes or if the brakes
are wet. When there is the risk that your
parking brake may freeze, temporarily
apply it with the gear in P (Park). Also,
block the rear wheels in advance, so the
vehicle may not roll. Then, release the
parking brake.
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, you should check underneath
the vehicle on a regular basis, to ensure
that the front wheels and the steering
components is unblocked.Carry emergency equipment
In accordance with weather conditions,
you should carry appropriate emergency
equipment, while driving. Some of the
items you may want to carry include tire
chains, tow straps or chains, flashlight,
emergency flares, sand, shovel, jumper
cables, window scraper, gloves, ground
cloth, coveralls, blanket, etc.
Do not place objects or materials in the
motor compartment
Putting objects or materials in the motor
compartment may cause an motor
failure or combustion, because they may
block the motor cooling. Such damage
will not be covered by the manufacturer’s
warranty.
Page 404 of 690
6-70
Driving Your Vehicle
Reference weight and distance when towing a trailer
ltemWithout
trailer
packageWith trailer package
Maximum trailer weight
Ibs. (kg)With brake
system- 2000 (907)
Without brake
system- 1653 (750)
Maximum permissible static vertical load on
the coupling device
Ibs. (kg)- 351 (159)
Recommended distance from rear wheel
center to coupling point
inch (mm)- 34.13 (867)
Page 406 of 690
6-72
Driving Your Vehicle
Driving with a Trailer
Towing a trailer requires a certain
amount of experience. Before setting
out for the open road, you must get to
know your trailer. Acquaint yourself with
the feel of handling and braking with the
added weight of the trailer. And always
keep in mind that the vehicle you are
driving is now longer and not nearly as
responsive as your vehicle is by itself.
Before you start, check the trailer hitch
and platform, safety chains, electrical
connector(s), lights, tires and brakes.
During your trip, occasionally check
to be sure that the load is secure, and
that the lights and trailer brakes are still
working.
Distance
Stay at least twice as far behind the
vehicle ahead as you would when driving
your vehicle without a trailer. This can
help you avoid situations that require
heavy braking and sudden turns.
Passing
You will need more passing distance up
ahead when you’re towing a trailer. And,
because of the increased vehicle length,
you’ll need to go much farther beyond
the passed vehicle before you can return
to your lane.
Backing up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, move your hand to the left. To
move the trailer to the right, move your
hand to the right. Always back up slowly
and, if possible, have someone guide
you.
Making turns
When you’re turning with a trailer, make
wider turns than normal. Do this so your
trailer won’t strike soft shoulders, curbs,
road signs, trees, or other objects. Avoid
jerky or sudden maneuvers. Signal well in
advance.
Turn signals
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you
signal a turn or lane change. Properly
connected, the trailer lights will also flash
to alert other drivers you’re about to turn,
change lanes, or stop.
When towing a trailer, the green arrows
on your instrument panel will flash for
turns even if the bulbs on the trailer
are burned out. Thus, you may think
drivers behind you are seeing your
signals when, in fact, they are not. It’s
important to check frequently to be sure
the trailer bulbs are still working. You
must also check the lights every time
you disconnect and then reconnect the
wires.
Page 408 of 690
6-74
Driving Your Vehicle
Parking on hills
Generally, if you have a trailer attached
to your vehicle, you should not park your
vehicle on a hill.
However, if you ever have to park your
trailer on a hill, here’s how to do it:
1. Pull the vehicle into the parking space.
Turn the steering wheel in the
direction of the curb (right if headed
down hill, left if headed up hill).
2. Shift the gear to P (Park).
3. Set the parking brake and shut off the
vehicle.
4. Place wheel chocks under the trailer
wheels on the down hill side of the
wheels.
5. Start the vehicle, hold the brakes, shift
to neutral, release the parking brake
and slowly release the brakes until the
trailer chocks absorb the load.
6. Reapply the brakes and parking
brakes.
7. Shift the gear to P (Park) when the
vehicle is parked on a uphill grade and
in R (Reverse) on a downhill.
8. Shut off the vehicle and release the
vehicle brakes but leave the parking
brake set.
WARNING
To prevent serious or fatal injury:
[ Do not get out of the vehicle without
the parking brake firmly set. If you
have left the motor running, the
vehicle can move suddenly. You and
others could be seriously or fatally
injured.
[ Do not apply the accelerator pedal to
hold the vehicle on an uphill.
Driving the vehicle after it has been
parked on a hill
1. With the gear in P (Park), apply your
brakes and hold the brake pedal down
while you:
[ Start your vehicle;
[ Shift into gear; and
[ Release the parking brake.
2. Slowly remove your foot from the
brake pedal.
3. Drive slowly until the trailer is clear of
the chocks.
4. Stop and have someone pick up and
store the chocks.
Page 422 of 690
7-8
Driver Assistance System
CAUTION
[ The setting of the Warning Timing
D Q G : D U Q L Q J 9 R O X P H D S S O L H V W R
all functions of Forward Collision-
$ Y R L G D Q F H $ V V L V W
[ ( Y H Q W K R X J K S 6 W D Q G D U GT L V V H O H F W H G
I R U : D U Q L Q J 7 L P L Q J L I W K H I U R Q W
Y H K L F O H V X G G H Q O \ V W R S V W K H Z D U Q L Q J
P D \ V H H P O D W H
[ 6 H O H F W S / D W HT I R U : D U Q L Q J 7 L P L Q J
Z K H Q W U D I I L F L V O L J K W D Q G Z K H Q G U L Y L Q J
V S H H G L V V O R Z
Information
If the vehicle is restarted, Warning Timing
and Warning Volume will maintain the
last setting.
) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
Assist Operation
Warning and control
The basic function for Forward Collision-
Avoidance Assist is to warn and help
control the vehicle depending on the
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’.
OJWEV071001L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate.
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6-124 mph (10-200
km/h).
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6-53 mph (10-85 km/h).
[ If ‘Active Assist’ is selected, braking
may be assisted.
Page 423 of 690
7-9
07
OJWEV071002L
( P H U J H Q F \ % U D N L Q J
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ If a vehicle is detected in front,
the function will operate when
your vehicle speed is between
approximately 6-53 mph (10-85 km/h).
[ If Forward Collision-Avoidance Assist
judges that avoiding a collision is
difficult even by changing the driving
lane, the function will operate when
your vehicle speed is between
approximately 6-62 mph (10-100
km/h) (if equipped with front corner
radar).
The function operation range may
decrease due to the front traffic
condition or the surroundings of the
vehicle.
[ If a pedestrian or cyclist is detected
in front, the function will operate
when your vehicle speed is between
approximately 6-40 mph (10-65
km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the vehicle, pedestrian
or cyclist ahead.
OJWEV071003L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Page 424 of 690
7-10
Driver Assistance System
Junction Turning function
Warning and control
Junction Turning function will warn and
control the vehicle depending on the
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’.
OJWEV071009L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the oncoming vehicle speed is
between approximately 19-44 mph
(30-70 km/h).
[ If ‘Active Assist’ is selected, braking
may be assisted.
OJWEV071239L
( P H U J H Q F \ % U D N L Q J
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the oncoming vehicle speed is
between approximately 19-44 mph
(30-70 km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the oncoming vehicle.
Information
If the driver's seat is on the left side,
Junction Turning function will operate
only when you turn left. If the driver's seat
position is on the right side, the function
will operate only when you turn right.
Page 425 of 690
7-11
07
OJWEV071003L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Junction Crossing function (if
equipped)
Warning and control
Junction Crossing function will warn
and control the vehicle depending on
collision risk level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’
OJWEV071004LOJWEV071005L
Collision Warning
[ To warn the driver of a collision, the
‘Collision Warning’ warning message
will appear on the cluster, an audible
warning will sound and the steering
wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the detected crossing vehicle
speed is between approximately 6-37
mph (10-60 km/h).
[ If ‘Active Assist’ and 'Forward Cross-
Traffic Safety' are selected, braking
may be assisted.
Page 426 of 690
7-12
Driver Assistance System
OJWEV071007LOJWEV071006L
( P H U J H Q F \ % U D N L Q J
[ To warn the driver that emergency
braking will be assisted, the
‘Emergency Braking’ warning
message will appear on the cluster,
an audible warning will sound and the
steering wheel will vibrate.
[ The function will operate when
your vehicle speed is between
approximately 6-19 mph (10-30 km/h)
and the detected crossing vehicle
speed is between approximately 6-12
mph (10-20 km/h).
[ In emergency braking situation,
braking is assisted with strong braking
power by the function to help prevent
collision with the crossing vehicle.
OJWEV071003L
6 W R S S L Q J Y H K L F O H D Q G H Q G L Q J E U D N H F R Q W U R O
[ When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
CAUTION
If the collision angle with the crossing
Y H K L F O H L V E H \ R Q G D F H U W D L Q U D Q J H
Junction Crossing function warning and
F R Q W U R O P D \ E H O D W H R U P D \ Q R W R S H U D W H