transmission GENESIS GV60 2023 Owners Manual

5-58
Convenience Features

[Visit the HomeLink website at: www.
homelink.com. Then at the top of the
page, choose your vehicle make. Then
watch the You Tube video, and/or
access additional website information.

[If you choose to access the website
via your cell phone, scan the QR code.

[Or, call HomeLink customer support
at 1-800-355-3515 (Please have the
vehicle make/model AND the opener
device make/model readily available.)
1) Programming Preparation
OJX1050293N
1. When programming a garage door
opener, it is advised to park the
vehicle outside of the garage.2. It is recommended that a new battery
be placed in the handheld transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the radio-
frequency signal.
3. Place the ignition switch to the ACC
(Accessory) position for programming
of HomeLink.
2) Programming a New HomeLink®
OJWEV051282N
1. Press and release the HomeLink
button (1), (2) or (3), you would like
to program. The HomeLink indicator
light (7) will flash orange slowly (if
not, perform the steps of “Erasing
HomeLink Buttons” section, and start
over).
OJX1050295N
2. Position the garage door opener
remote 1 – 3 inches (2 – 8cm) away
from the HoleLink buttons.

5-61
05
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light (7) is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
(7) changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.
2. Operating HomeLink®
1) Operating HomeLink®
OJWEV051282N
1. Press and release the desired
programmed HomeLink button (1, 2
or 3).
Information
The HomeLink indicator (7) should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.
2) Two-Way Communication Display
Behavior
OJWEV051283N
1. Press and release one of the
programmed HomeLink buttons (1, 2
or 3).
OJWEV051284N
2. The indicator (4) and (6) operates as
below, if your garage door opener
has Two-Way Communication
functionality.

6-68
Driving Your Vehicle
TRAILER TOWING
If you are considering to tow with your
vehicle, you should first check with your
state's Department of Motor Vehicles to
determine legal requirements. Since laws
vary from state to state the requirements
for towing trailers, cars, or other types of
vehicles or apparatus may differ. Ask an
authorized retailer of Genesis Branded
products for further details before
towing.
Remember that trailering is different
than just driving your vehicle by
itself. Trailering means changes in
handling, durability, and fuel economy.
Successful, safe trailering requires
correct equipment, and it has to be used
properly. Damage to your vehicle caused
by improper trailer towing is not covered
by your vehicle manufacturer’s warranty.
This section contains many time-tested,
important trailering tips and safety
rules. Many of these are important for
your safety and that of your passengers.
Please read this section carefully before
you pull a trailer.
WARNING
Take the following precautions:

[If you don’t use the correct
equipment and/or drive improperly,
you can lose control of the vehicle
when you are pulling a trailer. For
example, if the trailer is too heavy,
the braking performance may be
reduced. You and your passengers
could be seriously or fatally injured.
Pull a trailer only if you have followed
all the steps in this section.

[Before towing, make sure the
total trailer weight, GCW (Gross
Combination Weight), GVW (Gross
Vehicle Weight), GAW (Gross Axle
Weight) and trailer tongue load are
all within the limits.

[When you tow a trailer, make sure to
turn off the Idle Stop and Go system.
If You Decide to Pull a Trailer?
Here are some important points if you
decide to pull a trailer:

[Consider using a sway control. You
can ask a trailer hitch dealer about
sway control.

[Do not do any towing with your
vehicle during its first 1,200 miles
(2,000 km) in order to allow the
vehicle to properly break in. Failure to
heed this caution may result in serious
motor or transmission damage.

[When towing a trailer, be sure
to consult an authorized retailer
of Genesis Branded products for
further information on additional
requirements such as a towing kit, etc.

[Always drive your vehicle at posted
towing speed limit.

[Carefully observe the weight and load
limits provided in the following pages.

[When towing a trailer, be sure to
disable Reverse Parking Collision-
Avoidance Assist. If towing and going
in reverse the system will activate as it
detects the trailer. Also, before towing
a trailer disable all Driving Assistance
systems as precaution such as
Forward Collision–Avoidance Assist,
Lane Keeping Assist, Smart Cruise
Control and others.

6-73
06
WARNING
Do not connect a trailer lighting system
directly to your vehicle’s lighting
system. Use an approved trailer wiring
harness. Failure to do so could result in
damage to the vehicle electrical system
and/or personal injury. Consult an
authorized retailer of Genesis Branded
products for assistance.
Driving on hills
Reduce speed and shift to a lower gear
before you start down a long or steep
downgrade. If you don’t shift to a lower
gear, you may have to use your brakes
excessively and they would overheat and
may not operate efficiently.
On a long uphill grade, shift to a lower
gear and reduce your speed to around
45 mph (70 km/h) to reduce the
possibility of motor and transmission
overheating.
If your trailer weighs more than the
maximum trailer weight without trailer
brakes and you have an automatic
transmission, you should drive in D
(Drive) when towing a trailer.
Operating your vehicle in D (Drive)
when towing a trailer will minimize heat
build-up and extend the life of your
transmission.
NOTICE
To prevent motor and/or transmission
overheating:
When towing a trailer, your vehicle
speed may be much slower than the
general flow of traffic, especially when
climbing an uphill grade. Use the right
hand lane when towing a trailer on an
uphill grade. Choose your vehicle speed
according to the maximum posted
speed limit for vehicles with trailers, the
steepness of the grade, and your trailer
weight.

7-169
07
Information

[Check that all smart keys are outside
the vehicle when using Remote
Operation function.

[Remote Operation function will operate
only when the smart key is within
13 ft. (4 m) from the vehicle. If there
is no vehicle movement even when
the Forward or Backward button is
pressed on the smart key, check the
distance to the vehicle and press the
button again.

[The detecting range of the smart
key may vary depending on the
surroundings that are affected by radio
waves such as transmission tower,
broadcast station, etc.

[When remotely moving forward using
method (1), it is recognized as an exit
situation, and the vehicle moves 13
ft. (4 m) to check for parking lines,
pedestrians, animals or objects around
the vehicle. After confirmation, the
steering wheel is controlled according
to the condition ahead.

[When remotely moving forward
using method (2), it is recognized as a
parking situation, and will immediately
control the steering wheel according
to the condition ahead to assist with
entering the parking space and aligning
the vehicle. However, performance may
reduce depending on the parking lines
pedestrians, animals, shape of objects,
location, etc., around the vehicle.

[For moving remotely backward, both
method (1) and (2) aligns the steering
wheel first, and then will only move the
vehicle straight.

[When remotely moving forward or
backward is completed, the vehicle
will automatically shift to P (Park)
and engage EPB (Electronic Parking
Brake).
CAUTION

[When using Remote Operation
IXQFWLRQPDNHVXUHWKDWDOO
SDVVHQJHUVKDYHJRWWHQRXWRIWKH
YHKLFOH

[,IWKHYHKLFOH
TVEDWWHU\LVGLVFKDUJHG
or Remote Smart Parking Assist
malfunctions when parked in a
QDUURZSDUNLQJVSDFH5HPRWH
2SHUDWLRQIXQFWLRQZLOOQRWRSHUDWH
$OZD\VSDUN\RXUYHKLFOHLQDVSDFH
ZLGHHQRXJKIRU\RXWRJHWLQRURXW
RI\RXUYHKLFOH

[Please note that depending on the
SDUNLQJVSDFH\RXPD\QRWEHDEOH
WRH[LWIURPWKHVSDFH\RXKDYH
HQWHUHGE\XVLQJ5HPRWH2SHUDWLRQ
IXQFWLRQ

[$IWHUSDUNLQJWKHVXUURXQGLQJPD\
FKDQJHGXHWRWKHPRYHPHQWRI
VXUURXQGLQJYHKLFOHV,IWKLVRFFXUV
5HPRWH2SHUDWLRQIXQFWLRQPD\QRW
RSHUDWH

[%HIRUHOHDYLQJWKHYHKLFOHFORVH
ZLQGRZVDQGVXQURRIVDQGPDNH
VXUHWKHYHKLFOHLVRIIEHIRUHORFNLQJ
WKHGRRUV

7-177
07

[When operating Remote Smart
Parking function, make sure all
smart keys are outside of the
vehicle.

[Remote Smart Parking function will
operate only when the smart key is
within 13 ft. (4 m) from the vehicle.
If there is no vehicle movement
even when the Remote Forward or
Backward button is pressed on the
smart key, check the distance to the
vehicle and press the button again.

[The detecting range of the smart
key may vary depending on the
surroundings that are affected by
radio waves such as transmission
tower, broadcast station, etc.

[The parking location indicator is
displayed on Surround View Monitor
screen and is displayed until the
vehicle enters the parking space
for the first time by Remote Smart
Parking function.

[Depending on parking
environments, if the vehicle is
stopped by a stopper, parking may
be completed.

[If you need to change the vehicle's
position or location, manually
complete parking your vehicle.
CAUTION

[When using Remote Smart Parking
IXQFWLRQPDNHVXUHWKDWDOO
SDVVHQJHUVKDYHJRWWHQRXWRIWKH
YHKLFOH

[After ending or turning off Remote
6PDUW3DUNLQJIXQFWLRQEHIRUH
OHDYLQJWKHYHKLFOHFORVHZLQGRZV
DQGVXQURRIVDQGPDNHVXUHWKH
YHKLFOHLVRIIEHIRUHORFNLQJWKH
GRRUV
How to turn off Parking function
while operating

[Press the Parking/View () button
in the following stage:
- Searching for parking space
- Select parking type

[Shift the gear to R (Reverse) in the
following stage:
- Searching for parking space
- Select parking type
- Select operating mode

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen to turn off Parking
function.

[While Smart Parking function is
operating:
- If the vehicle is stopped by
depressing the brake pedal, and the
gear is shifted, Parking function will
turn off. At this time, EPB (Electronic
Parking Brake) will not be engaged.

[While Remote Smart Parking function
is operating:
- Press the Remote Start (
) button
on the smart key. Parking function
will turn off.
- Get on the vehicle with the smart
key. Parking function will turn off. At
this time, the vehicle will remain on.

7-186
Driver Assistance System

[The road surface is bumpy (curbstone,
speed bump, etc.)

[The road is slippery

[The parking space is near a vehicle
with higher ground clearance or big,
such as a truck, etc.

[The parking space is Inclined

[The road surface of parking space
with lines is wet due to snow, puddles,
or there is a road marker inside the
parking space

[The road surface of the parking space
with lines is bumpy due to road cracks

[The parking line is too thin or thick

[The parking line is partially erased or
blurred

[The parking line is obscured by
people, animals, or objects such as
snow, boxes, etc.

[There is heavy wind

[Operating Remote Smart Parking
Assist on uneven roads, gravel roads,
bushes, etc.

[The performance of the ultrasonic
sensor is affected by extremely hot or
cold weather

[The ultrasonic sensor is covered with
snow or water

[An object that generates ultrasonic
waves is nearby

[A wireless device with a transmission
function operates near the ultrasonic
sensors

[Your vehicle is affected by another
vehicle’s Parking Distance Warning

[The sensor is mounted or positioned
incorrectly by an impact to the
bumper

[The cameras is improperly mounted
or out of position due to outside
rearview mirror damage
[The ultrasonic sensor cannot detect
the following objects when:
- Sharp or slim objects, such as ropes,
chains or small poles
- Objects smaller than 40 in. (100 cm)
in length and narrower than 6 in. (14
cm) in diameter
- Objects which tend to absorb
sensor frequency, such as clothes,
spongy material or snow
- A narrow object such as a corner of
a square pillar
- Person, animal or object near the
ultrasonic sensor

[The cameras may not properly
recognize or may not recognize the
parking line and objects when:
- There are small objects (curb, etc.),
sharp objects, or thin objects (rope,
etc.) around
- People, animals or objects are too
close or too far from the vehicle
- Objects are on a higher position,
such as pickup trucks
- The camera is obscured by dirt or
moisture
- The camera is exposed to strong
light
- The surrounding is too dark
- The light is reflected from the
surface

8-20
Emergency Situations
Towing Service
OJWEV081011 [A] : Dollies
If emergency towing is necessary, have it
done by an authorized retailer of Genesis
Branded products or a commercial tow-
truck service.
Proper lifting and towing procedures
are necessary to prevent damage to
the vehicle. The use of wheel dollies or
flatbed is recommended.
For AWD vehicles, it must be towed
with a wheel lift and dollies or flatbed
equipment with all the wheels off the
ground.
Precautions when moving a
Short Distance before Towing a
Vehicle
Move short distances within 394 in. (10
m) at a speed of 3 mph (5 km/h) or less
only when loading on a tow truck of if the
vehicle needs to be repositioned. At this
time, the gear must be in the ‘N’(neutral)
position and the parking brake must be
released. If it is impossible to operate the
transmission and parking brake, move
the vehicle with the rear wheel lifted.
NOTICE
Do not lift the vehicle by the tow fitting
or body and chassis parts. Otherwise
the vehicle may be damaged.
If any of the loaded wheels or suspension
components are damaged or the vehicle
is being towed with the rear wheels on
the ground, use a towing dolly under the
rear wheels.
When being towed by a commercial tow
truck and wheel dollies are not used,
the rear of the vehicle should always be
lifted, not the front.
For AWD vehicles, it must be towed
with a wheel lift and dollies or flatbed
equipment with all the wheels off the
ground.
NOTICE
Do not lift the vehicle by the tow fitting
or body and chassis parts. Otherwise
the vehicle may be damaged.
TOWING

8-21
08
CAUTION

[Do not tow the vehicle with the 2WD:
rear, AWD: front/rear wheels on the
ground as this may cause damage to
the vehicle.
OJWEV081012

[Do not tow with sling-type
equipment. Use wheel lift or flatbed
equipment.
OJWEV081013
Move short distances within 394 in.(10
m) at a speed of 3 mph(5 km/h) or less
only when loading on a tow truck of if the
vehicle needs to be repositioned. At this
time, the gear must be in the ‘N’(neutral)
position and the parking brake must be
released. If it is impossible to operate the
transmission and parking brake, move
the vehicle with the rear wheel lifted.
CAUTION
Failure to shift the gear to N (Neutral)
may cause internal damage to the
reduction gear.
Removable Towing Hook
1. Open the liftgate, and remove the
towing hook from the tool case.
„Front
OJWEV081015
„Rear
OJWEV081017
2. Remove the hole cover by pressing
the lower part of the cover on the
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

9-30
Maintenance
WARNING
The traction grade assigned to
this tire is based on straight ahead
braking traction tests, and does not
include acceleration, cornering,
hydroplaning, or peak traction
characteristics.
Temperature - A, B & C
The temperature grades are A (the
highest), B and C representing the
tire’s resistance to the generation
of heat and its ability to dissipate
heat when tested under controlled
conditions on a specified indoor
laboratory test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life,
and excessive temperature can
lead to sudden tire failure. Grades
B and A represent higher levels of
performance on the laboratory test
wheel than the minimum required
by law.
WARNING
The temperature grade for this
tire is established for a tire that
is properly inflated and not
overloaded. Excessive speed,
under-inflation, over-inflation, or
excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden
tire failure. This may cause loss
of vehicle control resulting in an
accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim.