brake GMC C-SERIES 1999 Workshop Manual

yellowblue
4-31
Power Take-Off (PTO) (If Equipped)
Before using a PTO, refer to the body builder's or
operator's instructions.
To engage a PTO:
1. Make sure the vehicle is stopped.
2. Shift the transmission into NEUTRAL (N) or
PARK (P), if equipped.
3. The brake or clutch pedal must be pressed and
released once before PTO can be enabled. Do not
hold the brake or clutch pedal down.4. The cruise control switch must be in ON prior to
engaging the PTO switch to enable PTO operation.
This sets the PTO base engine idle at 1200 rpm.
5. Use SET/COAST to change the engine speed to the
lower preset value of 1400 rpm. Use
RESUME/ACCEL to change the engine speed to the
upper preset value of 1800 rpm. You may toggle
between upper and lower by moving the switch
between SET/COAST and RESUME/ACCEL.
The PTO will become inoperative when any of the
conditions are changed or the CHECK GAGES light
comes on.
ProCarManuals.com

yellowblue
5-10
CAUTION:
To help avoid injury to you or others:

Never let passengers ride in a vehicle that is
being towed.

Never tow faster than safe or posted speeds.

Never tow with damaged parts not
fully secured.

Never get under your vehicle after it has
been lifted.

Always use separate safety chains on each
side when towing a vehicle.
If your vehicle uses dragfoilers, be sure to have the
dragfoiler
-to-cab mounting bracket bolts tightened after
your vehicle has been towed.
Here are specific towing instructions:
Towing Your Vehicle From the
Front (Front Wheels Off the Ground)
Before Towing
Block the rear wheels of the disabled vehicle. On
vehicles with air brakes, release the emergency brake
system by compressing the brake chamber springs as
outlined in this section. (Note: This is to prevent the
possibility of the emergency brake being applied
during towing.)
On vehicles with hydraulic brakes without an
electric/hydraulic parking brake, release the
parking brake fully by moving the lever to the
fully
-released position.
On vehicles equipped with an electric/hydraulic parking
brake option, remove the propshaft.
ProCarManuals.com

yellowblue
5-14
After Towing
Block the rear wheels and install axle and propeller
shafts. Check for proper phasing of universal joints.
Apply the emergency brake system before disconnecting
from the towing vehicle. Check and fill the rear axle
with oil as required.
Towing Your Vehicle From the Front
(All Wheels On the Ground)
Your vehicle may be towed on all wheels provided the
steering is working. Remember that the power brakes
and power steering will not have power assist. Vehicles
with air brakes will not have brakes. There must be a
tow bar installed between the towing vehicle and the
disabled vehicle.
Before Towing
Block the wheels of the disabled vehicle. On vehicles
with air brakes, release the emergency brake system by
compressing the brake chamber springs as outlined in
this section. (Note: This is to prevent the possibility of
the emergency brake being applied during towing.)On vehicles with hydraulic brakes, release the
parking brake fully by moving the lever to the
fully
-released position.
On vehicles equipped with an electric/hydraulic parking
brake, remove the propshaft.
Disconnect the propshaft at the rear axle (forward axle
on tandem axle models). Secure the propshaft to the
frame or crossmember.
If there is damage or suspected damage to the axle(s),
remove the axle shafts. Cover the hub openings to
prevent the loss of lubricant or entry of dirt or
foreign objects.
After Towing
Block the rear wheels and install axle and propshafts.
Check for proper phasing of universal joints. Apply
the parking brake system before disconnecting from
the towing vehicle. Check and fill rear axle with oil
as required.
ProCarManuals.com

yellowblue
5-15 Towing Your Vehicle From the Rear
(Rear Wheels Off the Ground)
Before Towing
Secure the steering wheel to maintain a straight
-ahead
position. Make certain that the front axle is not loaded
above the front axle Gross Axle Weight Rating (GAWR)
as indicated on the vehicle's Certification/Tire label.
After Towing
Block the rear wheels and release the steering. Apply the
parking brake system before disconnecting from the
towing vehicle.
Refer to the transmission shift label for
additional information.
Releasing Air-Operated Parking Brakes
If your vehicle has air brakes, you could have a special
towing problem. If your vehicle has to be towed because
you had a complete loss of air pressure from both
systems, the parking brakes may have applied. The tow
operator can release the brakes manually by using the
following steps. Then your vehicle can be towed with all
wheels or just the rear wheels on the ground.
ProCarManuals.com

yellowblue
5-16
CAUTION:

Working on air brakes without first using
the release studs to compress the springs
can lead to injury. Never work on the air
brake chambers without first using the
release studs to compress the brake springs.

When the brake springs are manually
compressed, you will have no brakes.
Release your air
-operated parking brakes
manually only to tow the vehicle. Never
drive the vehicle with the brakes released.
1. Block the wheels of the vehicle.
2. Remove the release stud and nut from the side of the
brake chamber. Some chambers have studs which are
visible at all times.
ProCarManuals.com

yellowblue
5-17
3. Remove the rubber
cap from the rear of
the chamber.
4. Put the release stud, nut and flat washer into
the chamber.
5. Turn the stud clockwise a quarter of a turn.6. Using a wrench, turn the
stud nut clockwise
several turns to release
the brakes. Follow the
same procedure to
release the other brake.
7. At the repair facility, apply air pressure of at least
70 psi (480 kPa) to the brake chambers, either from
an external air supply or the vehicle's air system.
8. Turn the stud nut counterclockwise several turns.
Remove the stud from the chamber.
9. Put the stud into the side of the chamber, and replace
the rubber cap.
ProCarManuals.com

yellowblue
5-34
If a Tire Goes Flat
It's unusual for a tire to ªblow outº while you're driving,
especially if you maintain your tires properly. If air goes
out of a tire, it's much more likely to leak out slowly.
But if you should ever have a ªblowout,º here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you'd use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part tells you what to do.
Changing a Flat Tire
A flat or damaged tire can be a major roadside problem.
You're very likely to have to go for help. Few drivers of
these vehicles have the necessary equipment aboard to
be able to change a flat tire safely. For example, youhave to have a truck jack that can lift several thousand
pounds and a torque wrench that can generate several
hundred foot
-pounds (newton-meters) of twisting force.
So if you're stopped somewhere by a flat or damaged
tire or wheel, you should get expert help right then.
If the correct equipment is available, though, here is the
procedure to follow.

Does the tire still seem to have air under pressure in
it? If so, stand to the side and look at the wheel. See
if it looks like another wheel on the vehicle. If so, go
on to the next step. If it doesn't, or even if you can't
be sure, stop and get expert help.
CAUTION:
Tire-rim assemblies can explode. If you work on
a pressurized tire mounted on a damaged wheel,
the assembly can expand with explosive force
without warning. You and others nearby can be
badly injured. Don't work around a tire that has
air under pressure in it when its wheel is or might
be damaged.
ProCarManuals.com

yellowblue
5-37
CAUTION:
Incorrect wheel nuts or improperly tightened
wheel nuts can cause the wheel to become loose
and even come off. This could lead to an accident.
Be sure to use the correct wheel nuts. If you have
to replace them, be sure to get new GM original
equipment wheel nuts.
Stop somewhere as soon as you can and have the
nuts tightened with a torque wrench.
See ªTightening the Wheel Nutsº in the Index for
the proper torque for your particular wheel.
NOTICE:
Improperly tightened wheel nuts can lead to
brake pulsation and rotor damage. To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper
torque specification.
If You're Stuck: In Sand, Mud,
Ice or Snow
In order to free your vehicle when it is stuck, you will
need to spin the wheels, but you don't want to spin your
wheels too fast. The method known as ªrockingº can
help you get out when you're stuck, but you must
use caution.
CAUTION:
If you let your tires spin at high speed, they can
explode, and you or others could be injured. And,
the transmission or other parts of the vehicle can
overheat. That could cause an engine
compartment fire or other damage. When you're
stuck, spin the wheels as little as possible. Don't
spin the wheels above 35 mph (55 km/h) as shown
on the speedometer.
ProCarManuals.com

6-
yellowblue
6-1
Section 6 Service and Appearance Care
Here you will find information about the care of your vehicle. This section begins with service and fuel information,
and then it shows how to check important fluid and lubricant levels. There is also technical information about your
vehicle, and a part devoted to its appearance care.
6
-2 Service
6
-4 Fuel (Gasoline Engine)
6
-5 Diesel Fuel Requirements and Fuel System
6
-6 Fuels in Foreign Countries (Gasoline Engines)
6
-7 Filling Your Tank
6
-8 Filling a Portable Fuel Container
6
-9 Checking Things Under the Hood
6
-11 Noise Control System
6
-13 Engine Oil (Gasoline Engine)
6
-17 Engine Oil (Caterpillar
Diesel Engine)
6
-17 Engine Air Cleaner/Filter
6
-18 Automatic Transmission Fluid
6
-19 Manual Transmission Fluid
6
-20 Rear Axle
6
-20 Rear Axle Shift Motor (Option)
6
-21 Radiator Pressure Cap (Gasoline Engines)
6
-22 Surge Tank Pressure Cap (Diesel Engines)
6
-22 Thermostat6
-23 Engine Coolant (Gasoline Engine)
6
-27 Engine Coolant (Caterpillar
Diesel Engine)
6
-28 Power Steering Fluid
6
-29 Windshield Washer Fluid
6
-30 Brakes
6
-36 Electric/Hydraulic Parking Brake Fluid
6
-42 Battery
6
-44 Other Service Items
6
-48 Tires
6
-59 Appearance Care
6
-59 Cleaning the Inside of Your Vehicle
6
-63 Cleaning the Outside Your Vehicle
6
-66 GM Vehicle Care/Appearance Materials
6
-67 Vehicle Identification Number (VIN)
6
-67 Service Parts Identification Label
6
-68 Electrical System
6
-74 Capacities and Specifications
6
-77 Air Conditioning Refrigerants
ProCarManuals.com

yellowblue
6-11
Then place the prop rod,
located on the panel, where
the arrow is pointing.
CAUTION:
Things that burn can get on hot engine parts and
start a fire. These include liquids like gasoline or
diesel fuel, oil, coolant, brake fluid, windshield
washer and other fluids, and plastic or rubber. You
or others could be burned. Be careful not to drop
or spill things that will burn onto a hot engine.
Before closing the hood or access panels, be sure all the
filler caps are on properly.
Noise Control System
The following information relates to compliance with
Federal noise emission standards for vehicles with a
Gross Vehicle Weight Rating (GVWR) of more than
10,000 lbs. (4 536 kg). The Maintenance Schedule
provides information on maintaining the noise control
system to minimize degradation of the noise emission
control system during the life of your vehicle. The
noise control system warranty is given in your
Warranty booklet.
These standards apply only to vehicles sold in the
United States.
ProCarManuals.com