reset GMC C-SERIES 1999 Owners Manual

yellowblue
2-7
ACCESSORY (A): This position lets you use
accessories when the engine is off. To use
ACCESSORY, push in the key and turn it toward you.
LOCK (B): This position locks your ignition. You will
be able to remove your key only when the switch is in
this position.
OFF (C): This position lets you turn off the engine, but
the key can't be removed.
RUN (D): This is the position for driving and activating
the CAT diesel air inlet heater (if equipped).
START (E): This position starts your engine.
Engine Starter Over-Crank Protection
(If Equipped)
Some vehicles have an engine starter over-crank
protection system. This system includes a built
-in
temperature limiting switch to prevent internal damage
to the starter. If the starter motor overheats and shuts
off due to over
-cranking, the motor must cool down
before the switch will reset and allow you to operate the
starter. It can take up to six minutes before the starter
will work again.
Starting Your Gasoline Engine
Engines start differently. The 8th digit of your Vehicle
Identification Number (VIN) shows the code letter for
your engine. (See ªVehicle Identification Numberº in
the Index.) Follow the proper steps to start the engine.
To start a diesel engine, see ªStarting Your Diesel
Engineº in the Index.
Automatic Transmission
Set the parking brake and move your shift lever to
NEUTRAL (N) or PARK (P) if so equipped. Your
engine won't start in any other position
-- that's a
safety feature.
ProCarManuals.com

yellowblue
2-12 Fast Idle System (Electronically Controlled
Caterpillar

Diesel and Gasoline Engines)
If your vehicle is equipped with an electronically
controlled diesel engine, it has both automatic and
manual fast idle capabilities.
Automatic Fast Idle System
(Caterpillar

Diesel Engine Only)
The automatic fast idle feature will engage whenever
you start your vehicle and the engine is below the preset
operating temperature. This will help decrease engine
warm
-up time.
Idle speed will then return to normal under any of the
following conditions:

The engine reaches the preset operating temperature.

The brake pedal is pressed.

The trailer brake hand lever (if equipped) is applied.

The manual transmission clutch pedal is pressed or,
the automatic transmission (if equipped) is shifted
from NEUTRAL (N) or PARK (P).

The vehicle speed exceeds approximately
10 mph (16 km/h).

When the fast idle switch is pressed a second time.Manual Fast Idle System
(Caterpillar
 Diesel and Gasoline Engines)
The manual fast idle switch
is located on the lower
portion of the instrument
panel just to the left of the
steering wheel.
This system can be used to increase your engine idle
speed whenever the following conditions are met:

The brake pedal is not pressed.

The trailer brake hand lever (if equipped) is not applied.

The vehicle speed is below approximately
10 mph (16km/h).

The manual transmission (if equipped) clutch pedal
is not pressed or, the automatic transmission
(if equipped) is in NEUTRAL (N).
ProCarManuals.com

yellowblue
2-35
Low Speed Delay Wipers (If Equipped)
You can set the wiper speed
for a long or short delay
between wipes. This can be
very useful in light rain or
snow. Turn the band to
choose the delay time.
The closer to LO, the
shorter the delay.
Heavy snow or ice can overload your wipers. Clear
away snow or ice to prevent bending or breaking the
wiper linkage.
Windshield Washer
At the top of the multifunction lever, there's a paddle
with the word PUSH on it. To spray washer fluid on the
windshield, push the paddle.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
If you have the standard wipers, the wipers will keep
going in LO until you turn the wiper control to the
off symbol.
If you have the low
-speed delay option, the wipers will
clear the window and then either stop or return to your
preset speed.
ProCarManuals.com

yellowblue
2-66
A reading in the low pressure zone may be caused by a
dangerously low oil level or other problem.
If you have a Caterpillar

diesel engine, also see your
Caterpillar
Operation & Maintenance Manual.
CAUTION:
Don't keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
Change Oil Light (If Equipped)
The CHANGE OIL light
should come on briefly as a
bulb check when you start
the engine. If the light
doesn't come on, have
it serviced.
If the CHANGE OIL light comes on and stays on after
you start the engine, have the oil changed.
For additional information, see ªEngine Oil, When to
Changeº in the Index. To reset the Oil Life Monitor, see
ªEngine Oil Life Monitorº in the Index.
ProCarManuals.com

yellowblue
2-70 Filterminder Gage (Diesel Engine)
This optional gage is in the
lower center of the
instrument panel. It
monitors the engine
air filter.
As the filter gets dirty, the yellow indicator will begin to
rise. When it reaches 25 inches of vacuum on the scale,
the filter should be replaced.
After replacing the filter, reset the gage by pressing in
the yellow reset pin at the bottom of the gage.
If you have a diesel engine, also see your Caterpillar


Operation & Maintenance Manual.
Hourmeter Gage (If Equipped)
If your vehicle has this
gage, it will be to the lower
left of the steering column,
mounted on a bracket either
above or below the fuse
block. It shows the total
engine operating time.
ProCarManuals.com

yellowblue
3-9
5. Press one of the six pushbuttons within eight
seconds. In the display, SET will stop blinking
indicating the preset is set. Whenever you press that
numbered button, the station you set will return.
6. Repeat the steps for each pushbutton.
Also, you can use the automatic memory SET button
to set the pushbuttons. You can set up to 12 stations
(six AM and six FM). Just:
1. Press AM/FM to select a band.
2. Press and hold SET. (SET will appear on the display
and will blink.)
3. While pressing the SET button, press the SEEK
button. Release both switches. The radio will
automatically search the band and select radio
stations, up to six, which have good signal strength.Setting the Tone
BAS: Slide this lever left or right to decrease or increase
the bass.
TRE: Slide this lever left or right to decrease or
increase the treble. If a station is weak or noisy, you may
want to decrease the treble.
LOUD: To increase bass and treble at low volumes,
press this button. LOUD will appear in the display. Press
this button again to turn LOUD off.
Adjusting the Speakers
BAL: Slide this lever to the left or right to adjust
the speaker balance between the left and right speakers.
The middle position balances the sound between
the speakers.
FAD: Slide this lever to the left or right to adjust
the speaker balance between the front and rear speakers.
The middle position balances the sound between
the speakers.
ProCarManuals.com

yellowblue
4-31
Power Take-Off (PTO) (If Equipped)
Before using a PTO, refer to the body builder's or
operator's instructions.
To engage a PTO:
1. Make sure the vehicle is stopped.
2. Shift the transmission into NEUTRAL (N) or
PARK (P), if equipped.
3. The brake or clutch pedal must be pressed and
released once before PTO can be enabled. Do not
hold the brake or clutch pedal down.4. The cruise control switch must be in ON prior to
engaging the PTO switch to enable PTO operation.
This sets the PTO base engine idle at 1200 rpm.
5. Use SET/COAST to change the engine speed to the
lower preset value of 1400 rpm. Use
RESUME/ACCEL to change the engine speed to the
upper preset value of 1800 rpm. You may toggle
between upper and lower by moving the switch
between SET/COAST and RESUME/ACCEL.
The PTO will become inoperative when any of the
conditions are changed or the CHECK GAGES light
comes on.
ProCarManuals.com

yellowblue
6-16 Engine Oil Additives
Don't add anything to your oil. Your dealer is ready to
advise if you think something should be added.
When to Change Engine Oil
Your vehicle has a computer that lets you know when to
change your engine oil. This is not based on mileage,
but on engine revolutions and engine operating
temperature. When the computer has calculated that the
oil needs changing, the Oil Life Monitor will indicate
that a change is necessary. The mileage between oil
changes will vary depending on how you drive your
vehicle
-- usually between 3,000 miles (5 000 km) and
7,500 miles (12 500 km) since your last oil change.
Under severe conditions, the indicator may come on
before 3,000 miles (5 000 km). Never drive your vehicle
more than 7,500 miles (12 500 km) or 12 months
(whichever occurs first) without an oil change.
The system won't detect dust in the oil. So, if you
drive in a dusty area, be sure to change your oil every
3,000 miles (5 000 km) or sooner. Remember to reset
the CHANGE OIL light whenever the oil is changed.How to Reset the Oil Life Monitor
To reset the CHANGE OIL message, turn the ignition
key to RUN with the engine off. Fully press and release
the accelerator pedal three times within 10 seconds. If
the CHANGE OIL message flashes for five seconds, the
system is reset. If the message does not display for five
seconds, you will need to reset the system again.
What to Do with Used Oil
Did you know that used engine oil contains certain
elements that may be unhealthy for your skin and could
even cause cancer? Don't let used oil stay on your skin
for very long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly throw
away clothing or rags containing used engine oil. (See
the manufacturer's warnings about the use and disposal
of oil products.)
Used oil can be a real threat to the environment. If you
change your own oil, be sure to drain all free
-flowing oil
from the filter before disposal. Don't ever dispose of oil
by putting it in the trash, pouring it on the ground, into
sewers, or into streams or bodies of water. Instead,
recycle it by taking it to a place that collects used oil. If
you have a problem properly disposing of your used oil,
ask your dealer, a service station or a local recycling
center for help.
ProCarManuals.com

yellowblue
6-17
Engine Oil
(Caterpillar
Diesel Engines)
See your Caterpillar
Operation & Maintenance Manual
for information on oil quality and viscosities as well as
the temperature range chart.
Air Filter Restriction Indicator
Your engine has an indicator that lets you know when
the air filter is dirty and needs to be serviced. It is in the
air intake tube below the air cleaner on the passenger's
side of the engine.
When the yellow indicator
reaches the red ring in the
sight glass, it's time to
service the air filter.After the air filter is properly serviced, the indicator can
be reset by pushing the button on top of the indicator.
Engine Air Cleaner/Filter
Your GM Maintenance Schedule says when to replace
the air filter.
Gasoline Engine Caterpillar
Diesel
Engine
ProCarManuals.com

yellowblue
6-22
Surge Tank Pressure Cap
(Diesel Engines)
The surge tank pressure cap
must be tightly installed
with the arrows on the cap
lined up with the top tube of
the coolant surge tank.
When you replace your surge tank pressure cap, an
ACDelco

cap is recommended.
NOTICE:
Your surge tank pressure cap is a 9 psi (62kPa)
pressure
-type cap for use with medium duty
cooling systems only. It must be tightly installed
to prevent coolant loss and possible engine
damage from overheating. Be sure the arrows on
the cap line up with the top tube of the coolant
surge tank.
Thermostat
Engine coolant temperature is controlled by one or more
thermostats in the engine cooling system. The
thermostat stops the flow of coolant through the radiator
until the coolant reaches a preset temperature.
When you replace your thermostat, an ACDelco


thermostat is recommended for gasoline engines.
Caterpillar
parts are recommended for diesel engines.
ProCarManuals.com