tow bar GMC C-SERIES 1999 Owners Manual

yellowblue
1-5
To adjust the height of the
cushion, lift the cushion
height adjustment handle up
and forward. You can
choose between two
settings. The handle is
located underneath the seat,
in the front.
Lumbar Adjustments
To get more support in the
lumbar area of your back,
turn the lumbar adjustment
knob. The knob is located
on the upper cushion, on the
inboard side of the driver's
seat and the outboard side
of the passenger's seat.Seatback Adjustment
To tilt the seatback, turn the
backrest tilt knob. The knob
is located on the lower
cushion, on the outboard
side of the driver's seat and
the inboard side of the
passenger's seat.
Fore
-and-Aft Adjustment
To slide the seat forward or
backward, move the lever
toward the passenger's side.
The seat will lock in at
1/2 inch (1.5 cm)
increments. The lever is
located underneath the seat,
in the front.
ProCarManuals.com

yellowblue
3-5
OFF
Press this button to turn the air conditioning/heating
system off. Pressing OFF will erase the present mode of
operation from the system's memory. Outside air will
still come out of the heater outlet whenever the vehicle
is moving forward.
If the OFF button is pressed, you must press A/C,
MAX or one of the BLEND buttons to turn the system
back on.
Air Conditioning
When you first turn on your vehicle's air conditioning,
open the windows long enough to clear the vehicle of
hot air, then close them. Using the MAX button can also
help. See ªMAX Buttonº earlier in this section for
more information.
For normal cooling on hot days, use A/C with the
temperature selector toward C.
When you press the A/C button to turn the air
conditioner off, the system will operate in the vent
mode. When you turn the air conditioner back on, the
system will operate in the mode you last selected unless
the OFF button was pressed.If your air conditioner develops high system pressure, it
will automatically go into the MAX mode and REC will
light on your display. The A/C system will remain in the
MAX mode, even if you press the MAX button, until
system pressure returns to a normal level.
Heating
On cold days, use HEATER with the temperature
selector all the way toward H. When the inside of the
vehicle has reached a comfortable temperature, maintain
it by using the temperature selector bar.
If your vehicle is equipped with a diesel engine, and the
engine has been idling for a long time when it's cold
outside, your heater may blow out cool air. This is
normal. When you increase the engine speed under load,
your heater should blow out warmer air. If it doesn't,
your coolant level may be low. See ªEngine Coolantº in
the Index to check your coolant level.
While idling your diesel engine, you can use the MAX
button to recirculate the air in the cab to help maintain
interior heat. This will preserve engine coolant temperature
and cab heat when idling cannot be avoided.
Using the MAX button while driving is not recommended
because interior window fogging can result.
ProCarManuals.com

yellowblue
3-6 Defogging
Use DEFOG, along with the HEATER setting, when
there is fog or ice on the windshield. This will direct
airflow toward the windshield and front side windows.
Set the temperature selector toward H and the fan
control at a comfortable level. When the windshield is
clear, use the temperature selector bar and the fan
control button to maintain a comfortable
temperature level.
Ventilation System
Air comes into your vehicle in one of two ways: power air
or ram air. Power air means bringing outside air into the
cab through the air intake, using the blower fan. Fresh air
can be drawn in when the vehicle is stationary or moving
at low speed. Air comes in through four vents in the
instrument panel and is exhausted through the vents and
pressure relief valves in the doors and door pillars. Power
ventilation means an increased supply of fresh air is
brought into the cab interior without having to open the
windows, especially during inclement weather.
Ram air is forced into the cab through the air intake in
the cowl by the vehicle's forward motion. This air is
controlled by two vent air handles under the instrument
panel. Air is directed through the ventilation ducts to the
floor. Ram air provides good airflow into the cab at
normal road speeds.
ProCarManuals.com

yellowblue
5-11
Towing the Vehicle with the Front Bumper Removed
1. Remove the front bumper.
2. Connect and lock the lift chains to the front axle,
outside of the spring anchor plates as shown.
A. Spring Anchor Plate
B. Lift Chain
C. Front Axle
3. Place a 6, x 6, x 5
hardwood beam underneath and
slightly behind the front spring shackle brackets.4. Connect lift chains to the tow bar and raise the tow
bar until lift chain slack has been taken up and the
hardwood beam is fully seated against the spring
shackle brackets as shown.A. Shackle Bracket
B. Tow Bar
C. Lift Chain
D. Hardwood Beam
5. Raise the vehicle to the required height.
ProCarManuals.com

yellowblue
5-12
Towing the Vehicle with the Front Bumper Installed
1. Connect and lock the lift chains to the front axle,
outside of the spring anchor plates as
previously shown.
2. Place a 6, x 6, x 5
hardwood beam underneath and
slightly behind the front spring shackle brackets as
previously shown.
3. Connect the lift chains to the tow bar and take up the
slack in the chains until the tow bar is within 4, of
the front bumper facing. Place a 2, x 12, x 40,
hardwood board with rubber pads against the front
bumper and secure as shown.
A. Rubber Pad
B. Hardwood Board
C. Shackle Bracket
D. Lift ChainE. Hardwood Beam
F. Bumper
G. Tow Bar
4. Remove the remaining slack in the lift chains.
The tow bar swing arm should rest against the
2, x 12, x 40, hardwood board as shown.
ProCarManuals.com

yellowblue
5-14
After Towing
Block the rear wheels and install axle and propeller
shafts. Check for proper phasing of universal joints.
Apply the emergency brake system before disconnecting
from the towing vehicle. Check and fill the rear axle
with oil as required.
Towing Your Vehicle From the Front
(All Wheels On the Ground)
Your vehicle may be towed on all wheels provided the
steering is working. Remember that the power brakes
and power steering will not have power assist. Vehicles
with air brakes will not have brakes. There must be a
tow bar installed between the towing vehicle and the
disabled vehicle.
Before Towing
Block the wheels of the disabled vehicle. On vehicles
with air brakes, release the emergency brake system by
compressing the brake chamber springs as outlined in
this section. (Note: This is to prevent the possibility of
the emergency brake being applied during towing.)On vehicles with hydraulic brakes, release the
parking brake fully by moving the lever to the
fully
-released position.
On vehicles equipped with an electric/hydraulic parking
brake, remove the propshaft.
Disconnect the propshaft at the rear axle (forward axle
on tandem axle models). Secure the propshaft to the
frame or crossmember.
If there is damage or suspected damage to the axle(s),
remove the axle shafts. Cover the hub openings to
prevent the loss of lubricant or entry of dirt or
foreign objects.
After Towing
Block the rear wheels and install axle and propshafts.
Check for proper phasing of universal joints. Apply
the parking brake system before disconnecting from
the towing vehicle. Check and fill rear axle with oil
as required.
ProCarManuals.com