ignition GMC CANYON 2009 Get To Know Guide
[x] Cancel search | Manufacturer: GMC, Model Year: 2009, Model line: CANYON, Model: GMC CANYON 2009Pages: 20, PDF Size: 0.6 MB
Page 5 of 20

5
Check Warning Lights with OnStar
(if equipped)
If your vehicle is equipped with OnStar
and your Check Engine light or any
other warning message appears, you
can press the OnStar button and speak
to an OnStar Advisor. In many vehicles,
OnStar Advisors can access certain
diagnostic information and tell you how
serious the problem is and what you
should do about it.
See Section 3 of your Owner Manual.
SAFETY & SECURITY
Safety Belts
The safety belt shoulder straps feature
a park stitch (A) to prevent the safety
belt latch plate from contacting the
interior trim panel when the safety belt is
not in use. If you notice the latch plate
contacting the trim panel, make sure the
safety belt latch plate is located above
the park stitch in the belt.
A
Child Comfort Guide (Extended
Cabs and Crew Cabs only)
This feature provides added safety belt
comfort for smaller adults and for older
children who have outgrown booster
seats. When installed on a shoulder belt,
the comfort guide better positions the
belt away from the neck and head. One
comfort guide is provided for each rear
seat outboard position.
Safety Belt Reminder
When the ignition key is turned to On
or Start, a chime sounds for several
seconds to remind passengers to
buckle their safety belts. The safety belt
reminder light also illuminates and then
flashes for several seconds.
If the driver’s safety belt remains
unbuckled while the vehicle is in motion,
the chime will continue to sound and the
light will continue to flash.
See Sections 1 and 3 of your Owner Manual.
Page 6 of 20

Getting to Know Your Canyon6
Child Restraints (LATCH)
Your vehicle is equipped with LATCH
anchors, and may have top tethers for
use with a LATCH-compatible child
restraint. If your child restraint is not
compatible with the LATCH system, you
may still use it by installing the child
restraint with the safety belt system.
Automatic Door Locks
(if equipped)
For your safety, vehicles equipped with
power door locks and Remote Keyless
Entry are programmed at the factory to
lock all doors automatically. The doors
will lock when all doors are closed, the
ignition is on and the gearshift lever is
moved out of Park on vehicles with an
automatic transmission, or when vehicle
speed is greater than 15 mph on vehi-
cles with a manual transmission. This
feature cannot be disabled.
You can personalize the automatic
unlock features through the Driver
Information Center.
See Sections 2 and 3 of your Owner Manual.
Rear Door Security Locks
(Crew Cab models)
Crew Cab models are equipped with
rear door security locks that allow you to
lock the rear doors so they cannot be
opened by passengers from the inside.
The lock switch (shown above) is locat-
ed on the inside edge of each rear door.
Install a comfort guide on a shoulder
belt
1. Pull the elastic cord out from between
the seatback and the interior body to
remove the guide from its storage
clip.
2. Slide the guide under and past the
safety belt (the elastic cord must be
under the belt).
3. Place the guide over the belt and
insert the two edges of the belt into
the slots of the guide. (Be sure that
the belt is not twisted and that it lies
flat. The elastic cord must be under
the belt and the guide on top.)
4. Buckle, position and release the
safety belt as described in Section
1 of your Owner Manual. Make sure
the belt crosses the passenger’s
shoulder.
Storing the Child Comfort Guide
To remove and store the comfort guides,
squeeze the belt edges together so that
you can take them out of the guides.
Slide the guide back on its storage clip
located between the interior body and
the seatback. Storing the comfort guide
properly will prevent possible rattling.
See Section 1 of your Owner Manual.
Choose a child restraint that is appropri-
ate for the child’s age and size (weight
and height).
See Section 1 of your Owner Manual.
Page 7 of 20

7
Engage the rear door security locks
1. Open a rear door and insert your
ignition key into the lock.
2. On the driver’s side rear door, turn
the key clockwise to engage the rear
door security lock (turn it counter-
clockwise on the opposite side rear
door).
3. Close the door.
Open the rear door when the security
lock is on
• Unlock and open the door from
outside the vehicle.
Return the rear doors to normal use
• On the driver’s side rear door, insert
the key and turn the lock counter-
clockwise (turn it clockwise on the
opposite side rear door).
See Section 2 of your Owner Manual.
Passenger Airbag Status
Indicator
Your vehicle is equipped with a
Passenger Sensing System located in
the front passenger seat for the front
passenger frontal airbag, and a passen-
ger airbag status indicator located on
the center of the instrument panel.
See Sections 1 and 3 of your Owner Manual.
Note:It is recommended that children
not be placed in the front passenger
seat, even with the Passenger Sensing
System. All children should be secured
in a rear seat, including an infant riding
in a rear-facing infant seat, a child riding
in a forward-facing child seat or an older
child riding in a booster seat.
Content Theft-Deterrent System
(if equipped)
If your vehicle has the Remote Keyless
Entry (RKE) system, it also has a con-
tent theft-deterrent alarm system.
The content theft-
deterrent system is
armed when you
lock the doors with
the RKE transmitter
and all the doors
are closed. If the
lock button on the RKE transmitter is
pressed with a door open, the horn will
chirp several times. Close the door to
arm the system. The security light will
flash when the system is armed.
The system will not be armed if the
doors are locked with a key, the manual
door lock or the power door lock switch.
Alarm System
If a locked door is not opened using the
RKE transmitter or by OnStar, the horn
will chirp for several seconds and then
the alarm will sound. The alarm will flash
the front turn signal lamps and sound
the horn for two minutes.
To prevent the alarm from sounding,
unlock the doors using the RKE trans-
mitter. To turn off the alarm, press the
unlock button on the RKE transmitter or
start the engine using the correct key.
PASSlock
®
Your vehicle also is equipped with the
PASSlock theft-deterrent system that
requires the correct key be used to start
the engine. If the correct key is not used
or the ignition lock cylinder is tampered
with, the fuel system is disabled and the
engine will not start.
See Section 2 of your Owner Manual.
Page 9 of 20

9
The heated seat controls are located on
the outboard sides of the front seats.
(The ignition must be on for this feature
to work.)
Activate the heated seats
• Press the lower part of the switch to
turn on the heater to the LO setting.
• Press the upper part of the switch to
turn on the heater to the HI setting.
• Place the switch in the center position
to turn the heater off.
See Section 1 of your Owner Manual.
Note:In order for the passenger heated
seat to operate, the passenger safety
belt must be buckled.
Manual/Power Lumbar
(if equipped)
The manual lumbar control knob is
located on the outboard side of the driv-
er’s seat. Turn the knob counterclock-
wise to increase lumbar support and
clockwise to decrease lumbar support.
The power lumbar control switches for
the driver and passenger seats are
located on the outboard side of the
seats.
See Section 1 of your Owner Manual.
Preventing Window Fogging
ENTERTAINMENT
Audio Systems
AM/FM Stereo (if equipped)
Set the clock on the AM/FM stereo
radio
• Press and hold the HR button until
the correct hour appears.
• Press and hold MIN until the correct
minute appears.
Display the time with the ignition off
• Press RCL, HR or MIN. To clear fog or frost from the windshield
or side windows, turn the airflow control
knob to one of the following modes:
(Floor/Defog):Use to clear the
windows of moisture and to warm
passengers. This mode splits the air
delivery between the windshield and
the floor outlets.
(Defrost):Use to remove fog or
frost from the windshield more quickly.
This mode directs most of the air to
the windshield.
When you select the floor/defog or
defrost mode, the system automatically
turns off the recirculation mode and
runs the air conditioning compressor.
The recirculation mode cannot be
selected because outside air is needed
to remove interior moisture from the
vehicle.
See Section 3 of your Owner Manual.
Heated Seats (if equipped)
Page 13 of 20

13
Cargo Lamps (if equipped)
The cargo lamps provide illumination of
the cargo area and the interiors of the
top-box storage units. The controls are
located near the exterior lamps control.
Turn on the cargo lamps
• Press the button once.
The button’s indicator light will glow
when the lamps are on.
See Section 3 of your Owner Manual.
Note: To turn your cargo lamps on, the
dome lamp override must not be activat-
ed, and the dome lamps must be on.
Dome Lamp Override
To prevent your vehicle’s dome lamps
from illuminating when a door is opened,
press the dome lamp override button
located below the exterior lamps knob.
See Section 3 of your Owner Manual.
Turn off the fog lamps
• Press the button again.
The fog lamps will shut off whenever the
high beam headlamps are turned on,
and will reactivate when the high beam
headlamps are dimmed or turned off.
The fog lamps are canceled each time
the ignition is turned off and, when
needed, must be turned on manually
after restarting the vehicle.
See Section 3 of your Owner Manual.
Sunroof (if equipped)
The sunroof control buttons are located
on the headliner. The sunshade is
opened and closed manually.
Open/vent the sunroof
Press and hold the
button until the
sunroof is in the desired position.
Close the sunroof
Press and hold the
button until the
sunroof is in the desired position. After
closing the sunroof, continue to hold the
button for approximately two seconds to
ensure the sunroof is properly sealed.
See Section 2 of your Owner Manual.
Page 16 of 20

Getting to Know Your Canyon16
With four-wheel drive, you can send
power to all four wheels for extra trac-
tion. The controls are located on the
instrument panel, to the right of the
steering wheel.
Four-Wheel Drive Modes
2
(2HI): This setting is used for most
street and highway driving conditions.
The front axle is not engaged in this
mode.
Four-Wheel Drive System
(if equipped)
PERFORMANCE & MAINTENANCE
Starting Your Engine
With your foot off the accelerator pedal,
turn the ignition key to Start. When the
engine starts, let go of the key. Avoid
holding your key in the Start position
for longer than 15 seconds at a time.
Excessive starter operation can drain
your battery much sooner and excessive
heat can damage your starter motor. If
more than one try to start the engine is
necessary, wait about 15 seconds
between the first and second attempts.
See Section 2 of your Owner Manual.
Automatic Locking Differential
(if equipped)
Your axle may be equipped with an
automatic locking differential feature that
helps increase traction when traveling at
speeds less than 20 mph.
Once engaged, both rear wheels will
“lock” and rotate at the same speed,
improving vehicle traction. If one wheel
has poor traction, such as when on ice,
snow or mud, power will be transferred
to the wheel with better traction.
Resetting the Oil Life System
The Oil Life System calculates engine
oil life based on vehicle use and dis-
plays CHANGE OIL on the Driver
Information Center when it’s necessary
to change the engine oil and filter. The
Oil Life System should be reset only
following an oil change.
To reset the Oil Life System:
1. Turn on the ignition, with the
engine off.
2. Press and release the control stem
on the instrument cluster until OIL
LIFE is displayed.
3. Once the alternating OIL LIFE and
RESET messages appear, press and
hold the control stem until several
beeps sound. This confirms that the
Oil Life System has been reset.
4. Turn off the ignition.
See Sections 3 and 5 of your Owner Manual.
Note: The Oil Life System does not
replace the need to follow the mainte-
nance schedule in the Owner Manual.
It also does not measure how much oil
is in the engine.
Page 18 of 20

Getting to Know Your Canyon18
8. Turn the engine off.
9. Place the transmission shift
lever in Park (P), or First (1) for
vehicles equipped with a manual
transmission.
10.Turn the ignition to Lock.
11. Release the parking brake prior to
towing.
Shifting out of Neutral
1. Set the parking brake and press and
hold the regular brake pedal.
2. Shift the transmission to Neutral (N),
or press the clutch pedal for vehicles
with a manual transmission, and turn
the ignition to Run with the engine off.
3. Press the button for the desired
transfer case shift position (2HI,
4HI, or 4LO).
4. After the transfer case has shifted
out of Neutral, the indicator light will
go out.
5. Release the parking brake.
6. You may start the engine and shift
the transmission to the desired
position.
See Section 2 of your Owner Manual.
Shift the transfer case into or out of
Neutral
Shifting into Neutral
1. Set the parking brake.
2. Turn the ignition to Run but leave the
engine off.
3. Press the regular brake pedal and
shift the transmission in Neutral (N),
or depress the clutch for vehicles
with a manual transmission.
4. Shift the transfer case to two-wheel
high.
5. Press and hold the two-wheel high
and four-wheel low buttons at the
same time for 10 seconds. The
Neutral (N) light will come on when
the transfer case shift to Neutral (N)
is complete.
6. Start the engine.
7. Press and hold the regular brake
pedal and shift the transmission to
Reverse (R) for one second; then
shift the transmission to Drive (D) for
one second, or First (1) for vehicles
with manual transmissions and let
out the clutch, to ensure the transfer
case is in Neutral. If not, repeat this
procedure starting at the third step.
Note: Shifting the transfer case to
Neutral can cause your vehicle to roll
even if the transmission is in Park (P) or
in gear. You or someone else could be
seriously injured. Be sure to set the
parking brake before placing the trans-
fer case in Neutral.