wiring GMC SAVANA 1997 Owners Manual

Both rear doors can be opened past 90 degrees by
opening the doors past the first detent
(90 degrees open),
then opening fully.
To close the rear doors, close the driver side rear door
first. Then, close the passenger side rear door. Check to
make sure both doors are completely closed.
It can be dangerous to drive with the rear doors
open because carbon monoxide
(CO) gas can
come into your vehicle. You can’t see or smell
CO. It can cause unconsciousness and even death.
CAUTION: (Continued)
If you must drive with the rear doors open or if
electrical wiring or other cable connections must
pass through the seal between the body and the
rear doors:
0
0
0
Make sure all windows are shut.
Turn the fan on your heating or cooling
system to its highest speed with the setting
on VENT, HEAT, BLEND or DEF.
Additionally, on vehicles with heatingair
conditioning systems,
NORM A/C or
BI-LEV
A/C can be used. That will force
outside
air into your vehicle. See “Comfort
Controls” in the Index.
If you have air outlets on or under the
instrument panel, open them all the way.
See “Engine Exhaust” in the Index.
2-14
ProCarManuals.com

Rear Swing-Out Window
To close the window, pull the latch toward you and push
down
on the latch to lock it. Your rear swing-out
windows work the same way, but the latch is
at the
bottom edge
of the window.
It can be dangerous to drive with the rear
swing-out windows or rear door(s) open because
carbon monoxide
(CO) gas can come into your
vehicle. You can’t see or smell
CO. It can cause
unconsciousness and even death.
If you must drive with the rear swing-out
windows or rear door(s) open or
if electrical
wiring or other cable connections must pass
through the seal between the body and the rear
swing-out windows or rear door(s):
0 Make sure all windows are shut.
Turn the fan on your heating or cooling
system to its highest speed with the setting on
VENT, HEAT, BLEND or DEF. Additionally,
on vehicles with heatingair conditioning
systems,
NORM A/C or BI-LEV A/C can be
used. That will force outside air into your
vehicle. See
“Comfort Controls” in the Index.
instrument panel, open them
all the way.
If you have air outlets on or under the
See “Engine Exhaust” in the Index.
2-31
ProCarManuals.com

When the wheel is turned to full brilliance, and then into
the first detent position, the radio display and PRNDL
display will go to the day mode (full intensity). This is
known as “parade” mode. The rest
of the I/P
illumination will stay in the maximum dimming state
(full brilliance dimming). Turning the wheel up one
more detent will activate the interior dome light circuit
(with slightly higher effort).
The dome lights cannot be turned on by depressing the
dome light switch button, located below the parkhead
lamp switch knob. This switch is a dome lamp off
switch and will only interrupt inputs from the door jamb
switches, inhibiting interior light operation when
depressed. It will not inhibit the light function from the
I/P dimmer switch.
The delayed entry will allow
you to enter or exit your
vehicle with the lights staying
on for about 20 seconds
after the door
is closed or ignition is cycled.
Rotate the switch knob clockwise to the parking lamp
symbol to turn on:
0 Parking Lamps
0 Sidemarker Lamps
0 Taillamps
License Plate Lamps
Instrument Panel Lights
0 Ashtray Lamp
0 Glove Box Lamp
Rotate the switch
knob clockwise again to the master
lighting symbol to turn on all the lamps listed above as
well as the headlamps.
Rotate the switch counterclockwise to
OFF to turn off
your lamps and lights.
Rotate the thumb wheel next to the switch knob up to
adjust instrument panel lights. Rotate the thumb wheel
up to the first notch to return the radio display and
gearshift indicator Vacuum Fluorescence (VF) display
to full intensity when the headlamps or parking lamps
are on.
Rotate the thumb wheel up
to the second notch to
activate the interior dome lamps.
You can switch your headlamps from high to low beam
by pulling
on the turn signalhigh beam lever.
A circuit breaker protects your headlamps. If you have
an electrical overload, your headlamps will flicker on
and off. Have your headlamp wiring checked right away
if this happens.
ProCarManuals.com

Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows
AIR BAG. The system checks the
air bag’s electrical system
for malfunctions. The light
tells you if there
is an electrical problem. The system
check includes the air bag sensor, the
air bag modules,
the wiring and the crash sensing and diagnostic module.
For more information on the air bag system, see “Air
Bag” in the Index.
AIR
BAG
This light will come on
when you start your engine,
and it will flash for a few
seconds. Then the light
should go out. This means
the system is ready.
If the air bag readiness light stays on after you start the
engine or comes on when you are driving, your air bag
system may not work properly. Have your vehicle
serviced right away. The
air bag readiness light should
flash for a few
seconds when you turn the ignition key to
RUN. If the
light doesn’t come on then, have it fixed
so it will be
ready to warn
you if there is a problem.
Charging System Light
This light should come on
briefly when you turn
on the
ignition, before starting the
engine, as a check to show
you it is working.
After the engine starts, the light should go out. If
it stays
on or comes on while you are driving, you may have a
problem with your charging system. It could indicate a
problem with the alternator
drive belt, or some other
charging system problem. Have it checked right away.
Driving while this light is on could drain your battery.
If you must drive a short distance with this light on, it
helps to turn off all your accessories, such as the radio
and air conditioner.
2-51
ProCarManuals.com

Total Weight on Your Vehicle’s Tires
Be sure your vehicle’s tires are inflated to the upper
limit for cold tires. You’ll find these numbers
on the
Certification label at the rear edge of the driver’s door or
see “Tire Loading” in the Index. Then be sure you don’t
go over the
GVW limit for your vehicle, including the
weight of the trailer tongue.
Hitches
It’s important to have the correct hitch equipment.
Crosswinds, large trucks going by and rough roads
are a
few reasons why you’ll need the right hitch. Here are
some rules to follow:
The bumpers on your vehicle are not intended for
hitches.
Do not attach rental hitches or other
bumper-type hitches to them. Use only
a
frame-mounted hitch that does not attach to the
bumper.
Do not use a ball hitch, because it could pull
the bumper loose.
If you’ll be pulling a trailer that, when loaded, will
weigh more than
4,000 lbs. (1 800 kg), be sure to use
a properly mounted, weight-distributing hitch and
sway control of the proper size. This equipment
is
very important for proper vehicle loading and good
handling when you’re driving.
vehicle when you install a trailer hitch?
Will you have to make any holes in the body of your
If you’re using
the wiring provided by the
factory-installed hitch, you should not need to make
any holes in the body of your vehicle. However, if
you have an aftermarket hitch installed, you may
need to make holes
in the body.
If you do, then be sure to seal the holes later when
you remove the hitch. If you don’t seal them, deadly
carbon monoxide (CO) from your exhaust can get
into your vehicle (see “Carbon Monoxide” in the
Index). Dirt
and water can, too.
4-33
ProCarManuals.com

Making Turns
I NOTICE:
Making very sharp turns while trailering could cause the trailer to come in contact with the
vehicle. Your vehicle could be damaged. Avoid
making very sharp turns while trailering.
When you’re turning with a trailer, make wider turns
than normal.
Do this so your trailer won’t strike soft
shoulders, curbs, road signs, trees or other objects.
Avoid jerky or sudden maneuvers. Signal well
in advance.
limn Signals When Towing a Trailer
When you tow a trailer, your vehicle has to have extra
wiring and a heavy-duty turn signal flasher (included in
the optional trailering package).
The arrows on your instrument panel will flash
whenever you signal a turn or lane change. Properly
hooked up, the trailer lamps will also flash, telling other
drivers you’re about
to turn, change lanes or stop. When towing
a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on
the trailer
are burned out. Thus,
you may think drivers behind you
are seeing your signal when they are not. It’s important
to check occasionally
to be sure the trailer bulbs are
still working.
Driving On Grades
Reduce speed and shift to a lower gear before you
start down a long or steep downgrade. If you don’t shift
down, you might have to use your brakes
so much that
they would get hot and no longer work well.
On
a long uphill grade, shift down and reduce your
speed to around
45 mph (70 kmh) to reduce the
possibility
of engine and transmission overheating.
When towing at high altitude
on steep uphill grades,
consider the following: Engine coolant will boil at a
lower temperature than at normal altitudes. If you turn
your engine off immediately after towing at high altitude
on steep uphill grades, your vehicle may show signs
similar to engine overheating.
To avoid this, let the
engine run while parked (preferably on
level ground)
with the automatic transmission in PARK
(P) for a
few minutes before turning the engine
off. If you do
get the overheat warning, see “Engine Overheating”
in the Index.
4-36
ProCarManuals.com

Trailer Wiring Harness
The light-duty trailer wiring harness is a six-wire
harness assembly. The optional heavy-duty trailer
wiring package is
an eight-wire harness assembly. The
harness is stored under the vehicle, along the driver’s
side rear corner of the frame rail. The heavy-duty trailer
wiring harness has
a 30-amp feed wire. Both harnesses
come without connectors and should be wired
by a
qualified electrical technician. The technician can use
the following color code chart when connecting the
wiring harness to your trailer.
0
0
0
0
0
0
0
0
Dark Blue: Use for electric trailer brakes (eight-wire
harness only)
Orange: Trailer accessory (eight-wire harness only)
Light Green: Back-up lamps
Brown: Parking lamps
Yellow: Left stoplamp and turn signal
Dark Green: Right stoplamp and turn signal
White (heavy gage): Ground wire
White (light gage): Center high-mounted stoplamp
Securely attach the harness to the trailer, then tape or
strap it to your vehicle’s frame rail. Be sure you leave it
loose enough so the wiring doesn’t bend or break, but
not
so loose that it drags on the ground. Store the
harness in its original place. Wrap the harness together
and tie it neatly
so it won’t be damaged.
4-38
ProCarManuals.com

Electrical System
Add-on Electrical Equipment
I NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add-on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical
to your vehicle, see “Servicing
Your Air Bag-Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the lamp switch. An electrical overload will cause the
lamps to flicker on and off, or in some cases
to remain
off. If this happens, have your headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
Although the circuit is protected from electrical
overload, overload due to heavy snow, etc., may cause
wiper linkage damage. Always clear ice and heavy snow
from the the windshield before using the windshield
wipers. If the overload is caused by some electrical
problem and not snow, etc., be sure to get it fixed.
6-59
ProCarManuals.com

Halogen Bulbs ................................ 6-32 .
Hazard Warning Flashers .......................... 5-2
Head Restraints
................................. 1-5
Headlamps .................................... 2-39
Bulb Replacement
............................ 6-33
High/Low Beam Changer
...................... 2-34
OnReminder
................................ 2-40
Wiring
..................................... 6-59
Hearing Impaired. Customer Assistance
.............. 8-4
Heating
........................................ 3-7
High-Beam Headlamps
.......................... 2-34
Highway Hypnosis
.............................. 4-22
Hill and Mountain Roads
......................... 4-22
Hitches. Trailer
................................. 4-33
Hood
Checking Things Under
......................... 6-7
Prop
........................................ 6-8
Release
...................................... 6-7
Horn ......................................... 2-32
Hydroplaning
.................................. 4-18
Ignition Switch
................................ 2- 16
Ignition Transmission Lock Check
................. 7-47
Inflation. Tire
.................................. 6-42
Inside Daymight Rearview Mirror
................. 2-43
Inspections
.................................... 7-49
Brakesystem
................................ 7-50
Exhaust Systems
............................. 7-49
Radiator and Heater Hose
...................... 7-49
RearAxle
................................... 7-50 Steering
.................................... 7-49
Suspension
.................................. 7-49
Throttle Linkage
.............................. 7-49
Brightness Control
............................ 2-38
Cleaning
.................................... 6-52
Cluster ..................................... 2-48
FuseBlock
.................................. 6-60
Interior Lamps ................................. 2-40
.................................... J ack. Tire 5-25
Jump Starting
................................... 5-3
Keyless Entry System
........................... 2-6
Keys
.......................................... 2-2
Labels 4-27
Certification
................................. 4-27
CertificationEire
............................. 4-27
Service Parts Identification
..................... 6-58
Tire-Loading Information
...................... 4-27
Vehicle Identification Number
................... 6-58
Lamps
........................................ 2-38
Dome
...................................... 2-40
Interior
..................................... 2-40
OnReminder
................................ 2-40
Panel
....................................... 2-40
Underhood
.................................. 2-42
Leaving
Your Vehicle with the Engine Running ....... 2-26
Lighter ....................................... 2-45
9-5
ProCarManuals.com

..
Top Strap ..................................... 1-42
Torque Lock ................................... 2-26
Torque. Wheel Nut
......................... 5-34. 6-65
Towing a Trailer ................................ 4-29
Towing Your Vehicle
............................. 5-8
Driving on Grades
............................ 4-36
Maintenance When Towing
..................... 4-37
Safety Chains
................................ 4-34
Tongueweight
............................... 4-32
Total Weight on Tires
.......................... 4-33
Trailer
Brakes
..................................... 4-34
Drivingwith
................................. 4-34
Hitches
..................................... 4-33
ParkingonHills
.............................. 4-37
Towing
..................................... 4-29
Turnsignals
................................. 4-36
Weight
..................................... 4-31
Wiring Harness
............................... 4-38
Automatic
................................... 6- 18
Transmitters. Keyless Entry
........................ 2-7
Transportation, Courtesy
.......................... 8-8
Trip Odometer ................................. 2-49
Turn Signal and Lane Change Signals
............... 2-33
Turn SignaUMultifunction Lever ................... 2-33
Turn Signals When Towing a Trailer
................ 4-36
Transmission Fluid
TTYUsers
..................................... 8-4
Underbody Maintenance ........................ 6-56
Underhood
Lamp ............................... 2-42
Vehicle Control
...................................... 4-6
Damage Warnings
.............................. iv
Identification Number
......................... 6-58
Ventilation System
............................... 3-7
Visor Vanity Mirrors
............................ 2-46
Loading
.................................... 4-27
Storage
..................................... 6-32
Visors, Sun .................................... 2-46
warning Devices
............................... 5-3
Warning Lights. Gages and Indicators
............... 2-50
Washer Fluid. Windshield
........................ 6-27
Washing Your Vehicle
........................... 6-54
Weatherstrips
.................................. 6-53
Nut Torque
............................ 5-34, 6-65
Replacement
................................. 6-47
Warranty
Information
............................ 8-10
Wheel
Alignment
.................................. 6-47
Wrench
..................................... 5-26
Windows
..................................... 2-29
Power
...................................... 2-29
SideLatches
................................. 2-30
Swing-Out
.................................. 2-30
9-10 r
ProCarManuals.com