lock GMC YUKON 2002 Owner's Manual
[x] Cancel search | Manufacturer: GMC, Model Year: 2002, Model line: YUKON, Model: GMC YUKON 2002Pages: 443, PDF Size: 2.97 MB
Page 9 of 443
1-2
Seats and Seat Controls
This section tells you about the seats -- how to adjust
them, and fold them up and down. It also tells you about
reclining front seatbacks and head restraints.
Manual Front Seat
CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver's seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
don't want to. Adjust the driver's seat only when
the vehicle is not moving.
If your vehicle has a manual bucket or a split bench seat,
you can adjust it with this lever located at the front of
the seat.
Lift the lever to unlock the seat. Using your body, slide
the seat to where you want it and release the lever. Try
to move the seat with your body to make sure the seat is
locked into place.
Page 13 of 443
1-6 Heated Front Seats (If Equipped)
If your vehicle has this
feature, the button used to
control the driver's heated
seat is located on the
driver's door panel. The
button used to control the
passenger's heated seat is
located on the passenger's
door panel.
To activate the heated seats, press the button once for
the HI heat setting. Press the button again for the LO
heat setting. To turn off the heated seats, press the
button a third time. An indicator light will illuminate for
each heat setting anytime the heated seats are operating.
The ignition must be in RUN for them to operate.
The heated front seats will be canceled after the ignition
is turned to OFF. If you still want to use the heated front
seat feature after you restart your vehicle, you will need
to press the heated seat button again.
Reclining Seatbacks
To adjust the front seatback, lift the manual lever located
on the outboard side of the seat. Release the lever to
lock the seatback where you want it. Lift the lever again
without pushing on the seatback and the seatback will
go to an upright position.
If your vehicle has power seats with a power recliner,
see ªPower Seatsº in the Index for further information
on how to operate the reclining seatback feature.
Page 16 of 443
1-9
Folding the Seatbacks
CAUTION:
If the seatback isn't locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
press rearward on the seatback to be sure it
is locked.
On all models with 60/40 split bench seats, you must
insert the center occupant lap belt latch plate into the
loop provided, on the underside of the folded forward
seat cushion, before folding the rear seat back down on
the driver's side.
You may have to adjust the location of the latch plate on
the webbing so that it reaches the loop. Stowing in this
loop will reduce the chances of damaging and soiling
the belt. Remember to remove the latch plate from the
loop before the seat is returned to the passenger position.
On Suburban/Yukon XL insert the two buckles into
the retainer in the seatback, before folding the rear
seat on the driver's side. The buckles will be out of
the way when the seat is folded and will be available
for passengers to use when the seat is returned to the
passenger position. Also, make sure that nothing is
under or in front of the seat and that the head restraints
are completely lowered.
On Tahoe/Yukon models the rear seatbacks may be
equipped with rearward folding head restraints. When
the seatback is being folded down, the head restraint will
automatically fold rearward to allow a flat load floor for
cargo or entry to the third row seat (if equipped).
Page 18 of 443
1-11
Make sure that the buckles on the driver's side seatback
are accessible to the outboard and center occupant and
are not under the seat cushions.
On Tahoe/Yukon models make sure the head restraints
are returned to the upright position.
Bucket Seats (Suburban/Yukon XL
Second Row)
If your vehicle has bucket seats, the seatbacks can be
reclined and the seats can be folded to give you more
cargo room.
Reclining the Seatbacks
On the Suburban/Yukon XL models with bucket seats,
the seatbacks can be reclined. To adjust the seatback do
the following:
1. Pull forward the lever located at the base of the back.
2. Release the lever to lock the seatback where you
want it. If you pull the lever without pushing on the
seatback, the seatback will go to an upright position.Folding the Seatbacks
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
The seatbacks on the bucket seats may be folded
forward to give you more cargo space.
In order to fold the back of a bucket seat into a
horizontal load floor, the back must be in its upright
position, and not reclined.
Page 20 of 443
1-13
Once the seatbacks are folded down, the rear seat
footwell area will be exposed and will have to be
covered by the load floor panel. To create a load
floor, do the following:
1. Release the panels from the seatbacks by pushing
forward on the latches.
2. Then fold the panels back to cover the rear seat
footwell area.
If you have removed the head restraints to fold the rear
bucket seat, be sure to reinstall them on the seatback
after it has been returned to the normal seating position.
50/50 Split Bench Seat (Third Row)
If your vehicle has a 50/50 split bench, the seatback(s)
can be folded and the entire seat(s) tilted or removed
from the vehicles.
Folding the Seatbacks
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
To fold the seatbacks do the following:
Pull up on the release lever, labeled 1, located on the
rear of the seatback, and push the seatback forward.
To return the seat to the passenger position, pull
up on the release lever labeled 1 and then pull up
on the seatback until the seatback locks into the
upright position.
Push forward on the seatback to make sure it is locked
into position.
Page 21 of 443
1-14
Tilting the 50/50 Split Bench Seat
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
CAUTION:
If the support rod isn't properly engaged, the
folded third row seat could come loose in a
sudden stop or crash. That could cause injury to
people and damage to your vehicle. Always be
sure the support rod is properly engaged when
the third row seat is folded forward.
Once the third seatback has been folded down, the
entire seat can be tilted forward to create a flat load
floor. To do this, do the following:
1. Enter the rear cargo area of the vehicle.
2. Make sure the head restraints have been
lowered completely.
3. With the seat folded, unlatch the seat from the floor
by pulling up on the lever located under the carrying
handle at the rear of the seat labeled 2.
4. Lift the rear of the seat up, off the floor. You will not
be able to unlatch the seat from the floor unless the
seatback is folded down.
5. Tilt the seat fully forward and secure it in place using
the support rod located on the underside of the seat
on the passenger's side. Make sure the rod pin is
fully engaged in the lock.
6. Push and pull on the seat. Make sure the support rod is
holding it firmly in place. Use the seat in this position
only when necessary for additional cargo space.
Page 22 of 443
1-15
To return the seat to the seating position do the
following:
1. Push forward on the seat and release the support
lock rod.
2. Secure the support rod in its stored position on the
underside of the seat.
3. Lower the seat to the floor and let the seat drop
into place.
4. Lift up on the carrying handle to make sure the seat
is locked in place.
5. Return the seatback to the upright position by pulling
up on the release lever labeled 1 before the back can
be folded upright.
6. Pull the seatback forward to make sure it is locked
in place.
Removing the 50/50 Split Bench Seat
To remove the 50/50 split bench seat, do the following:
1. Open the rear doors and enter the rear of the vehicle.2. Fold the seatback
forward onto the seat
cushion by using the
lever labeled 1. The seat
cannot be removed
unless the seatback
is folded.
3. To unlatch the seat from
the floor, pull up on the
release lever labeled 2,
located at the rear of the
seat, and lift the rear of
the seat up off the floor.
Page 23 of 443
1-16
4. Squeeze the release lever, located in the lower
middle to unlatch the seat from the floor, while
pulling the seat out.
5. While holding the rear of the seat up, roll the seat out
of the vehicle.
Replacing the 50/50 Split Bench Seat
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
CAUTION:
A seat that isn't locked into place properly can
move around in a collision or sudden stop. People
in the vehicle could be injured. Be sure to lock
the seat into place properly when installing it.
CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted won't provide the
protection needed in a crash. The person wearing
the belt could be seriously injured. After
installing the seat, always check to be sure that
the safety belts are properly routed and attached,
and are not twisted.
To reinstall the 50/50 split bench, do the following:
1. While holding the rear of the seat up, slide the front
wheels into the slots on the floor. The front latches
should lock into place. If the latches do not lock, try
tilting the rear of the seats upwards.
2. Once the latches are engaged, let the seat drop into
place. Release the lever labeled 1 to return the seat to
its upright position.
3. Push and pull on the seat to make sure it is
locked into place. The seatback cannot be raised
to the upright position unless the seat is secured
to the floor.
Page 24 of 443
1-17 Full Bench Seat (Third Row)
If your vehicle has a full bench seat, the seatback can
be folded and the seat can be tilted or removed from
the vehicle.
Folding the Seatback
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
To fold the seatback on the bench seat, do the following:
1. Pull up on the release
lever, labeled 1, located
on the rear of the
seatback and push the
seatback forward.
2. To return the seat to an upright position, pull up
on the release lever labeled 1 and then pull up on
the seatback until the seatback locks into the
upright position.
Push and pull on the seatback to check that it is locked
into place.
Page 25 of 443
1-18
Tilting the Full Bench Seat
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
CAUTION:
If the support rod isn't properly engaged, the
folded third row seat could come loose in a
sudden stop or crash. That could cause injury to
people and damage to your vehicle. Always be
sure the support rod is properly engaged when
the third row seat is folded forward.
Once the third seatback has been folded down, the entire
seat can be tilted forward to create a flat load floor. To
do this, do the following:
1. Enter the rear cargo area of the vehicle.
2. Make sure the head restraints have been
lowered completely.
3. With the seat folded,
unlatch the seat from the
floor by pulling up on
the lever located under
the carrying handle at
the rear of the seat
labeled 2.
4. Lift the rear of the seat up, off the floor. You will not
be able to unlatch the seat from the floor unless the
seatback is folded down.