display GMC YUKON 2003 Owners Manual
[x] Cancel search | Manufacturer: GMC, Model Year: 2003, Model line: YUKON, Model: GMC YUKON 2003Pages: 520, PDF Size: 2.92 MB
Page 289 of 520

Remember: Anti-lock doesn’t change the time you need
to get your foot up to the brake pedal or always
decrease stopping distance. If you get too close to the
vehicle in front of you, you won’t have time to apply
your brakes if that vehicle suddenly slows or stops.
Always leave enough room up ahead to stop, even
though you have anti-lock brakes.
Using Anti-Lock
Don’t pump the brakes. Just hold the brake pedal down
rmly and let anti-lock work for you. You may feel
the brakes vibrate, or you may notice some noise, but
this is normal.
Braking in Emergencies
With anti-lock, you can steer and brake at the same
time. In many emergencies, steering can help you more
than even the very best braking.
Supplemental Brake Assist System
If your vehicle has vacuum assist power brakes, it is also
equipped with a supplemental brake assist system
that supplies additional vacuum to the vacuum brake
booster if engine vacuum is reduced. Under certain
conditions, the supplemental brake assist system may
run brie y after starting your vehicle or when you
apply and release the brake pedal and it may continueto run even after you have removed your foot from the
brake pedal. When the supplemental brake assist
system is operating, you may hear a motor running or
feel a slight vibration in the steering wheel or brake
pedal. This indicates that the supplemental brake assist
system is working to supply additional vacuum for
your vacuum assist power brakes. This is a normal
operation of your brake system and does not require that
the brake system be serviced.
Each time you start your vehicle and accelerate to
10 mph, the supplemental brake assist system
will perform a self-diagnostic check of the system and
you may hear or feel the supplemental brake assist
motor run brie y. While you are driving your vehicle, the
supplemental brake assist system monitors itself to
ensure that it is operating properly. If there is a problem
with the supplemental brake assist system, the
SERVICE BRAKE BOOSTER message will be displayed
on the Driver Information Center. SeeDIC Warnings
and Messages on page 3-64.
If your supplemental brake assist system runs every
time you apply and release the brake pedal or you notice
that the brake pedal has suddenly become much
harder to push and the vehicle takes longer to stop, you
should have your vehicle serviced as soon as possible.
4-9
2003 - Yukon/Yukon XL
Page 292 of 520

The next time you start your vehicle, the TAS will not
automatically come on. You can restore the automatic
feature by using the same procedure. Whether the TAS
is set to come on automatically or not, you can always
turn the system on or off by pressing the TAS on/off
button.
Locking Rear Axle
If your vehicle has this feature, your locking rear axle
can give you additional traction on snow, mud, ice, sand
or gravel. It works like a standard axle most of the
time, but when one of the rear wheels has no traction
and the other does, this feature will allow the wheel with
traction to move the vehicle.
Stabilitrak®System
Your vehicle is equipped with the Stabilitrak®which
combines antilock brake, traction and stability control
systems and helps the driver maintain directional control
of the vehicle in most driving conditions.
When you rst start your vehicle and begin to drive
away, the system performs several diagnostic checks to
insure there are no problems. You may hear or feel
the system working. This is normal and does not mean
there is a problem with your vehicle. The system
should initialize before the vehicle reaches 20 m.p.h.
(32 km/h). In some cases, it may take approximately
two miles of driving before the system initializes.If the system fails to turn on or activate, the STABILITY
SYS DISABLED or SERVICE STABILITY message
will be displayed. If the vehicle has gone through heavy
acceleration or braking during the rst two miles after
starting your vehicle, the STABILITY SYS DISABLED
message may appear. If this is the case, your
vehicle does not need servicing. Turn your vehicle off
and back on again to reset the system. If either message
appears on the Driver Information Center (DIC), and
your vehicle hasn’t gone through hard acceleration
or braking in the rst two miles, your vehicle should be
taken in for service.
The STABILITY SYS ACTIVE message will appear on
the Driver Information Center (DIC) only when the
system is both on and activated. You may also feel or
hear the system working; this is normal. For more
information on the stability messages, seeDriver
Information Center (DIC) on page 3-53.
The Stabilitrak
®mode
button is located on the
instrument panel.
4-12
2003 - Yukon/Yukon XL
Page 293 of 520

Stabilitrak®and part of the traction control system can
be turned off or back on by pressing the
Stabilitrak
®button. All-wheel drive vehicles must be in
all-wheel drive mode to turn the system on or off.
When the system is turned off, the traction off light will
illuminate, and the STABILITY SYS DISABLED
message will appear on the DIC to warn the driver that
both the stability system and part of the traction
control system are disabled. Your vehicle will still have
brake-traction control when Stabilitrak
®is off, but
will not be able to use the engine speed management
system. See“Traction Control Operation”next for
more information.
When the Stabilitrak
®system has been turned off you
may still hear system noises as a result of the
brake-traction control coming on.
It is recommended to leave the system on for normal
driving conditions, but it may be necessary to turn
the system off if your vehicle is stuck in sand, mud, ice
or snow, and you want to“rock”your vehicle to
attempt to free it. It may also be necessary to turn off
the system when driving in extreme off-road conditions
where high wheel spin is required. SeeIf You Are
Stuck: In Sand, Mud, Ice or Snow on page 4-52.
When the transfer case is in 4 low, the stability system
is automatically disabled, and the STABILITY SYS
DISABLED message will appear on the DIC. In 4 low,
the Stabilitrak
®button only turns the traction control
system on and off.
Traction Control Operation
The traction control system is part of the
Stabilitrak®system. Traction control limits wheel spin by
reducing engine power to the wheels (engine speed
management) and by applying brakes to each individual
wheel (brake-traction control) as necessary.
The traction control system is enabled automatically
when you start your vehicle, and it will activate and
display the TRACTION ACTIVE message in the Driver
Information Center (DIC) if it senses that any of the
wheels are spinning or beginning to lose traction while
driving. If you turn off Stabilitrak
®, only the brake-traction
control portion of traction control will work. The engine
speed management will be disabled. In this state, engine
power is not reduced automatically and the driven wheels
can spin more freely. This can cause the brake-traction
control to activate constantly. For more information on the
traction active message, seeDriver Information Center
(DIC) on page 3-53.
Notice:If the traction off light comes on due to
heavy braking and/or because the traction control
system has been continuously active, do not
allow the wheel(s) of one axle to spin excessively.If
you do, you may be causing damage to your
transfer case.This could lead to costly repairs not
covered by your warranty.
4-13
2003 - Yukon/Yukon XL
Page 294 of 520

If the brake-traction control system activates constantly
or if the brakes have heated up due to high speed
braking, the brake-traction control will be automatically
disabled. The system will come back on after the
brakes have cooled. This can take up to two minutes or
longer depending on brake usage.
Notice:Don’t allow the wheel(s) of one axle to spin
excessively when the traction off, ABS and brake
lights are on and the SERVICE STABILITY MESSAGE
is displayed. In this situation, damage to the
transfer case is possible. This could lead to costly
repairs not covered by your warranty. You should
immediately reduce engine power until the lights
and messages are no longer displayed.
The traction control system may activate on dry or
rough roads or under conditions such as heavy
acceleration while turning or abrupt upshifts/downshifts
of the transmission. When this happens you may
notice a reduction in acceleration, or may hear a noise
or vibration. This is normal.
If your vehicle is in cruise control when the system
activates, the STABILITY SYS ACTIVE message will
appear on the Driver Information Center and the cruise
control will automatically disengage. When road
conditions allow you to use cruise again, you may
re-engage the cruise control. See“Cruise Control”under
Turn Signal/Multifunction Lever on page 3-8Stabilitrak®may also turn off automatically if it
determines that a problem exists with the system. If the
problem does not clear itself after restarting the
vehicle, you should see your dealer for service.
Steering
Power Steering
If you lose power steering assist because the engine
stops or the system is not functioning, you can steer but
it will take much more effort.
Steering Tips
Driving on Curves
It’s important to take curves at a reasonable speed.
A lot of the“driver lost control”accidents mentioned on
the news happen on curves. Here’s why:
Experienced driver or beginner, each of us is subject to
the same laws of physics when driving on curves.
The traction of the tires against the road surface makes
it possible for the vehicle to change its path when
you turn the front wheels. If there’s no traction, inertia
will keep the vehicle going in the same direction. If
you’ve ever tried to steer a vehicle on wet ice, you’ll
understand this.
4-14
2003 - Yukon/Yukon XL
Page 374 of 520

How to Reset the CHANGE ENGINE OIL
Message
The GM Oil Life System calculates when to change
your engine oil andfilter based on vehicle use. Anytime
your oil is changed, reset the system so it can
calculate when the next oil change is required. If a
situation occurs where you can change your oil prior to
a CHANGE ENGINE OIL message being turned on,
reset the system.
To reset the CHANGE ENGINE OIL message, see“GM
Oil Life System”underDIC Operation and Displays
on page 3-54for vehicles equipped with the DIC, or do
the following:
1. Turn the ignition key to RUN with the engine off.
2. Fully press and release the accelerator pedal three
times withinfive seconds.
If the OIL LIFE RESET messageflashes for 10 seconds,
the system is reset.
If the system does not reset, try the procedure once
again. If it still does not reset, see your dealer for
service.
What to Do with Used Oil
Used engine oil contains certain elements that may be
unhealthy for your skin and could even cause cancer.
Don’t let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good
hand cleaner. Wash or properly dispose of clothing or
rags containing used engine oil. See the manufacturer’s
warnings about the use and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil from the
filter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or into
streams or bodies of water. Instead, recycle it by
taking it to a place that collects used oil. If you have a
problem properly disposing of your used oil, ask
your dealer, a service station or a local recycling center
for help.
5-20
2003 - Yukon/Yukon XL
Page 383 of 520

Coolant Surge Tank Pressure Cap
SeeEngine Compartment
Overview on page 5-12for
more information on
location.
The coolant surge tank pressure cap must be fully
installed on the coolant surge tank.
Notice:Your pressure cap is a pressure-type cap
and must be tightly installed to prevent coolant loss
and possible engine damage from overheating.
See“Capacities and Speci cations”for more
information.
Engine Overheating
You willfind a coolant temperature gage on your
vehicle’s instrument panel. SeeEngine Coolant
Temperature Gage on page 3-46. In addition, you will
find a LOW COOLANT LEVEL, ENGINE OVERHEATED
and a REDUCED ENGINE POWER message in the
DIC on the instrument panel. SeeDriver Information
Center (DIC) on page 3-53.
Overheated Engine Protection
Operating Mode (V8 Engines Only)
If an overheated engine condition exists and the
REDUCED ENGINE POWER message is displayed, an
overheat protection mode which alternatesfiring
groups of cylinders helps prevent engine damage. In
this mode, you will notice a loss in power and engine
performance. This operating mode allows your vehicle to
be driven to a safe place in an emergency. Driving
extended miles (km) and/or towing a trailer in the
overheat protection mode should be avoided.
Notice:After driving in the overheated engine
protection operating mode, to avoid engine damage,
allow the engine to cool before attempting any repair.
The engine oil will be severely degraded. Repair the
cause of coolant loss, change the oil and reset the oil
life system. See“Engine Oil”in the Index.
5-29
2003 - Yukon/Yukon XL
Page 501 of 520

D
Daytime Running Lamps..................................3-16
Defensive Driving............................................. 4-2
Defogging and Defrosting.........................3-24, 3-30
Delayed Locking............................................... 2-9
Dinghy Towing................................................4-55
Doing Your Own Service Work........................... 5-3
Dolly Towing..................................................4-57
Dome Lamps .................................................3-20
Door
Delayed Locking........................................... 2-9
Locks.......................................................... 2-7
Power Door Locks......................................... 2-8
Programmable Automatic Door Locks............... 2-9
Rear Door Security Locks.............................2-11
Driver
Position, Safety Belt.....................................1-28
DRIVER DOOR AJAR.....................................3-69
Driver Information Center (DIC).........................3-53
DIC Operation and Displays..........................3-54
DIC Warnings and Messages........................3-64
Driving
At Night
.....................................................4-37
City
...........................................................4-42Driving (cont.)
Defensive..................................................... 4-2
Drunken....................................................... 4-2
Freeway.....................................................4-43
Hill and Mountain Roads..............................4-45
In Rain and on Wet Roads...........................4-39
Winter........................................................4-47
Driving Across an Incline..................................4-33
Driving Downhill..............................................4-32
Driving in Mud, Sand, Snow or Ice....................4-35
Driving in Water..............................................4-36
Driving On Grades..........................................4-70
Driving on Off-Road Hills.................................4-28
Driving on Snow or Ice....................................4-48
Driving Through Deep Standing Water...............4-40
Driving Through Flowing Water.........................4-41
Driving Uphill..................................................4-29
Driving with a Trailer.......................................4-68
Dual Automatic Climate Control System.............3-26
Dual Climate Control System............................3-22
DVD
Cleaning the Video Screen..........................3-125
Distortion..................................................3-123
Rear Seat Entertainment System..................3-111
DVD Player..................................................3-111
5
2003 - Yukon/Yukon XL
Page 502 of 520

E
Easy Exit Seat...............................................2-60
Electrical System
Add-On Equipment......................................5-97
Fuses and Circuit Breakers...........................5-98
Power Windows and Other Power Options......5-97
Windshield Wiper Fuses...............................5-97
Electrochromic Mirror Operation................2-41, 2-43
Emissions Inspection and Maintenance
Programs...................................................3-50
Engine
Air Cleaner/Filter.........................................5-21
Battery.......................................................5-43
Check and Service Engine Soon Light............3-48
Compartment Overview................................5-12
Coolant......................................................5-26
Coolant Heater............................................2-21
Coolant Temperature Gage...........................3-46
Cooling System Inspection............................6-16
Exhaust.....................................................2-38
Fan Noise..................................................5-37
Oil .............................................................5-16
Overheating................................................5-29
Starting
......................................................2-20
ENGINE COOLANT HOT
.................................3-64
Engine Coolant Level Check
.............................6-11
Engine Hour Meter Display
...............................3-39Engine Oil Additives........................................5-19
Engine Oil Level Check...................................6-11
ENGINE OVERHEATED..................................3-65
Entering or Exiting the Third Row Seats.............. 1-8
Entertainment System
Cleaning the Video Screen..........................3-125
DVD Distortion..........................................3-123
Entry Lighting.................................................3-18
Environmental Concerns..................................4-26
Erasing HomeLink
®Buttons..............................2-53
Exit Lighting...................................................3-18
Express-Down Windows...................................2-15
Extender, Safety Belt.......................................1-43
Exterior Lamps...............................................3-14
F
Filter
Engine Air Cleaner......................................5-21
Finding a PTY Station
(RDS and XM™) .......................3-78, 3-88, 3-101
Finding a Station....................3-73, 3-76, 3-86, 3-99
Finish Care....................................................5-92
Finish Damage...............................................5-94
Fixed Mast Antenna.......................................3-125
Flash-To-Pass.................................................. 3-9
Flat Tire........................................................5-69
Flat Tire, Changing.........................................5-69
6
2003 - Yukon/Yukon XL
Page 506 of 520

Locks (cont.)
Rear Door Security Locks.............................2-11
Loss of Control...............................................4-21
LOW COOLANT LEVEL..................................3-64
Low Fuel Warning Light...................................3-53
Luggage Carrier..............................................2-55
Lumbar
Power Controls............................................. 1-5
M
Maintenance, Normal Replacement Parts..........5-109
Maintenance Schedule
At Each Fuel Fill.........................................6-11
At Least Once a Month................................6-11
At Least Once a Year..................................6-12
At Least Twice a Year..................................6-12
Brake System Inspection..............................6-16
Engine Cooling System Inspection.................6-16
Exhaust System Inspection...........................6-15
Fuel System Inspection................................6-15
How This Section is Organized....................... 6-3
Introduction.................................................. 6-2
Maintenance Requirements............................. 6-2
Part A - Scheduled Maintenance Services......... 6-4
Part B - Owner Checks and Services.............6-11
Part C - Periodic Maintenance Inspections......6-15
PartD-Recommended Fluids and
Lubricants...............................................6-17
PartE-Maintenance Record........................6-19Maintenance Schedule (cont.)
Scheduled Maintenance................................. 6-5
Steering and Suspension Inspection...............6-15
Transfer Case and Front Axle (Four-Wheel
Drive) Inspection......................................6-16
Using Your................................................... 6-4
Your Vehicle and the Environment................... 6-2
Maintenance When Trailer Towing.....................4-72
Making Turns.................................................4-70
Malfunction Indicator Light................................3-48
Manual Seats................................................... 1-3
Manual Windows............................................2-14
Matching Transmitter(s) to Your Vehicle............... 2-6
Memory Seat.................................................2-58
Message
DIC Warnings and Messages........................3-64
Mexico, Central America and Caribbean Islands/
Countries (Except Puerto Rico and U.S. Virgin
Islands)....................................................... 7-4
Mirrors
Automatic Dimming Rearview with Compass
and Temperature Display
...........................2-43
Automatic Dimming Rearview with OnStar
®,
Compass and Temperature Display
.............2-40
Manual Rearview Mirror
................................2-40
Outside Automatic Dimming Mirror
.................2-47
Outside Camper-Type Mirrors
........................2-46
Outside Convex Mirror
.................................2-48
Outside Curb View Assist Mirrors
...................2-47
Outside Heated Mirrors
................................2-48
10
2003 - Yukon/Yukon XL
Page 509 of 520

Rear Axle......................................................5-50
Locking......................................................4-12
Rear Door Security Locks................................2-11
Rear Safety Belt Comfort Guides......................1-41
Rear Seat Audio Controls...............................3-121
Rear Seat Audio (RSA)..................................3-120
Rear Seat Entertainment System.....................3-111
Rear Seat Operation......................................... 1-8
Rear Seat Outside Passenger Positions.............1-38
Rear Seat Passengers, Safety Belts..................1-38
Rear Storage Area..........................................2-56
Rear Window Defogger............................3-24, 3-31
Rearview Mirror, Automatic Dimming with
Compass and Temperature Display................2-43
Rearview Mirror, Automatic Dimming with
OnStar
®, Compass and Temperature Display . . . 2-40
Rearview Mirrors.............................................2-40
Reclining Seatbacks.......................................... 1-6
Reclining the Seatbacks...................................1-20
Recreational Vehicle Towing.............................4-55
REDUCED ENGINE POWER...........................3-65
Remote Alarm.................................................. 2-5
Remote Control.............................................3-114
Remote Keyless Entry System............................ 2-4
Remote Keyless Entry System, Operation............ 2-5
Removing the 50/50 Split Bench Seat
................1-13
Removing the Bench Seat
................................1-18
Removing the Flat Tire and Installing the
Spare Tire
..................................................5-74
Removing the Spare Tire and Tools
...................5-70Replacement Bulbs
.........................................5-59
Replacing Brake System Parts
..........................5-43
Replacing Restraint System Parts After a Crash
.....1-87
Replacing the 50/50 Split Bench Seat
................1-14
Replacing the Bench Seat
................................1-19
Reporting Safety Defects
Canadian Government
..................................7-10
General Motors
...........................................7-10
United States Government
.............................. 7-9
Reprogramming a Single HomeLink
®Button
.......2-53
Resetting Defaults
...........................................2-54
Restraint System Check
...................................6-12
Checking Your Restraint Systems
...................1-86
Replacing Restraint System Parts After a
Crash
.....................................................1-87
Restraint Systems
Checking
....................................................1-86
Replacing Parts
...........................................1-87
Resynchronization
............................................. 2-7
Retained Accessory Power (RAP)
......................2-19
RFA # BATTERY LOW
....................................3-69
Right Front Passenger Position, Safety Belts
......1-36
RIGHT REAR DOOR AJAR
..............................3-69
Roadside
Assistance Program
....................................... 7-5
Rocking Your Vehicle To Get It Out
...................4-52
Running Your Engine While You Are Parked
.......2-39
13
2003 - Yukon/Yukon XL