power steering fluid GMC YUKON XL 2002 Owners Manual

2-19Engine Coolant Heater (If Equipped) In very cold weather,
0
F (
- 18
C) or
colder, the engine
coolant heater can
help. You'll get easier
starting and better fuel
economy during
engine warm
- up.
Usually, the coolant heater should be plugged in a
minimum of four hours prior to starting your vehicle.
At temperatures above 32
F (0
C), use of the coolant
heater is not required.
To Use the Engine Coolant Heater 1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
The cord is located on the driver's side of the engine
compartment, near the power steering fluid reservoir.
3. Plug it into a normal, grounded 110
- volt AC outlet. CAUTION: Plugging the cord into an ungrounded outlet
could cause an electrical shock. Also, the wrong
kind of extension cord could overheat and cause
a fire. You could be seriously injured. Plug the
cord into a properly grounded three
- prong
11 0
- volt AC outlet. If the cord won't reach, use a
heavy
- duty three
- prong extension cord rated for
at least 15 amps.
4. Before starting the engine, be sure to unplug
and store the cord as it was before to keep it away
from moving engine parts. If you don't, it could
be damaged.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature, the
kind of oil you have, and some other things. Instead of
trying to list everything here, we ask that you contact
your dealer in the area where you'll be parking your
vehicle. The dealer can give you the best advice for that
particular area.

6-
6-1Section 6 Service and Appearance CareHere you will find information about the care of your vehicle. This section begins with service and fuel information,
and then it shows how to check important fluid and lubricant levels. There is also technical information about your
vehicle, and a part devoted to its appearance care.
6
- 2 Service
6
- 3 Fuel
6
- 5 Fuels in Foreign Countries
6
- 6 Filling Your Tank
6
- 8 Filling a Portable Fuel Container
6
- 8 Checking Things Under the Hood
6
- 11 Engine Oil
6
- 17 Engine Air Cleaner/Filter
6
- 19 Passenger Compartment Air Filter
6
- 20 Automatic Transmission Fluid
6
- 23 Rear Axle
6
- 24 All
- Wheel Drive
6
- 26 Engine Coolant
6
- 29 Coolant Surge Tank Pressure Cap
6
- 30 Power Steering Fluid 6
- 31 Windshield Washer Fluid
6
- 32 Brakes
6
- 36 Battery
6
- 37 Bulb Replacement
6
- 41 Windshield Wiper Blade Replacement
6
- 42 Tires
6
- 51 Appearance Care
6
- 51 Cleaning the Inside of Your Vehicle
6
- 55 Cleaning the Outside of Your Vehicle
6
- 59 GM Vehicle Care/Appearance Materials
6
- 60 Vehicle Identification Number (VIN)
6
- 61 Electrical System
6
- 69 Replacement Bulbs
6
- 70 Capacities and Specifications
6
- 71 Normal Maintenance Replacement Parts

6-11A. Engine Air Cleaner/Filter
B. Coolant Surge Tank
C. Air Filter Restriction Indicator
D. Engine Oil Dipstick
E. Engine Oil Fill
F. Automatic Transmission Dipstick
G. Fan
H. Remote Negative (
- ) Terminal (GND)
I. Remote Positive (+) Terminal
J. Power Steering Fluid Reservoir (Out of View)
K. Brake Master Cylinder Reservoir
L. Underhood Fuse Block
M. Battery
N. Windshield Washer Fluid Reservoir
Before closing the hood, be sure all filler caps are on
properly. Pull down the hood and close it firmly. Engine Oil If the CHECK ENG OIL
LEVEL message appears
on the instrument cluster,
it means you need to check
your engine oil level
right away.
For more information, see ªCHECK ENG OIL LEVELº
in the Index.
You should check your engine oil level regularly; this is
an added reminder.

6-30Power Steering Fluid
When to Check Power Steering Fluid It is not necessary to regularly check power steering
fluid unless you suspect there is a leak in the system or
you hear an unusual noise. A fluid loss in this system
could indicate a problem. Have the system inspected and
repaired. See ªEngine Compartment Overviewº in the
Index for reservoir location. How to Check Power Steering Fluid Turn the key off, let the engine compartment cool down,
wipe the cap and the top of the reservoir clean, then
unscrew the cap and wipe the dipstick with a clean rag.
Replace the cap and completely tighten it. Then remove
the cap again and look at the fluid level on the dipstick.
The level should be at the FULL COLD mark.
If necessary, add only enough fluid to bring the level
up to the mark.
What to Use To determine what kind of fluid to use, see
ªRecommended Fluids and Lubricantsº in the Index.
Always use the proper fluid. Failure to use the proper
fluid can cause leaks and damage hoses and seals.

7-23Part D: Recommended Fluids
and Lubricants Fluids and lubricants identified below by name,
part number or specification may be obtained from
your dealer.
USAGE FLUID/LUBRICANT
Engine Oil Engine oil with the American
Petroleum Institute Certified
for Gasoline Engines starburst
symbol of the proper viscosity.
To determine the preferred
viscosity for your vehicle's engine,
see ªEngine Oilº in the Index.
Engine Coolant 50/50 mixture of clean,
drinkable water and use only
GM Goodwrench

DEX
- COOL

or Havoline

DEX
- COOL

Coolant. See ªEngine Coolantº
in the Index. USAGE FLUID/LUBRICANT
Hydraulic
Brake System Delco Supreme 11

Brake Fluid
(GM Part No. 12377967 or
equivalent DOT
- 3 brake fluid).
Windshield
Washer Solvent GM Optikleen

Washer Solvent
(GM Part No. 1051515)
or equivalent.
Power
Steering System GM Power Steering Fluid
(GM Part No. 1052884
- 1 pint,
1050017
- 1 quart, or equivalent).
Automatic
Transmission DEXRON

- III Automatic
Transmission Fluid.
Key
Lock Cylinders Multi
- Purpose Lubricant,
Superlube

(GM Part
No. 12346241 or equivalent).
Chassis
Lubrication Chassis Lubricant
(GM Part No. 12377985 or
equivalent) or lubricant meeting
requirements of NLGI # 2,
Category LB or GC
- LB.