Body electric GREAT WALL DEER 2006 Owners Manual

BE-80
Wire harness at tail door and of rear air-conditioner
SY SJ
wire harness of rear
air-conditionerwire harness
of rear brush
1
2
3456
7
8V 10 1112 13
NQ
Only the vehicle with SY model has the wire harness of rear air-conditioner shown in above-mentioned wire harness.
1 rear A/C switch
2 connected to cab wire harness
3 rear air-conditioning relay
4 grounding wire
5 temperature control switch
6 electromagnetic valve
7 temperature controller8 speed-adjusting resistance
9 license lamp
10 license lamp
11 rear brusher motor
12 defroster
13 defroster
14 connected to cab wire harness
Body Electric System
Wire Harness Distribution

BE-81
SF
1 connected to left rear wire harness
2 connected to left rear wire harness
3 lock switch at left tail door
4 electro-heating gate at tail door
5 electro-heating gate at tail door
6 left license lamp7 electric rocker at tail door
8 right license lamp
9 lower limit switch at tail door
10 alarming switch at tail door
11 lock barrel at tail door
12 lock switch at right tail door 12
3
4
5
67
89
10
1112
Wire harness at tail door (continued)
Body Electric System
Wire Harness Distribution

BE-82
Chassis Wire Harness
Dr
12
3456 7 8
910
11
12
1 connected to cab wire harness
2 back up radar
3 fuel pump
4 fuel sensor
5 left backup radar probe
6 left rear fog lamp7 left license lamp
8 left rear combination lamp
9 right backup radar probe
10 right rear fog lamp
11 right license lamp
12 right rear combination lamp
Body Electric System
Wire Harness Distribution

BE-83
SL SK
1 connected to cab wire harness
2 fuel pump
3 grounding wire
4 connected to wire harness
5 connected to chassis wire harness
6 right rear combination lamp7 right rear fog lamp
8 back up radar control box
9 right license lamp
10 left license lamp
11 left rear fog lamp
12 left rear combination lamp Tail lamp wire harness should be fixed at the inner side of the rear baffle of load-compartment.
1
23
4 56
7
8
9
10
11
12 chassis wire harness tail lamp wire harness
Chassis wire harness (continued)
Body Electric System
Wire Harness Distribution

BE-84
SY SJ
only for SJ model vehicle
N2
3
45
6
Chassis Wire Harness (continued)
Body Electric System
Wire Harness Distribution
1 connected to cab wire harness
2 right rear combination lamp
3 right rear fog lamp
4 electric fuel pump
5 left rear fog lamp
6 left rear combination

BE-85
SF
1 fuel level sensor
2 electric fuel pump
3 connected to cab wire harness
1
2
3
Chassis Wire Harness (continued)
Body Electric System
Wire Harness Distribution

B0-4Vehicle Body
Front Door
Front door
Element figure
(glass)
glasschannel
outer auchi
inner tri-angle trim panel
door limiting device
door hinge
indoor handle
seal strip on
door plate
electric switch
and panel
interior trim panel
of electric door
(Dr)
interior trim panel
of electric door
(SF) interior trim panel of
electric door
sleeve
snapping ring elevator handle
(SL SK SY SJ)
door lamp
inner clip
lower rear glass
guide track sliding channelsmall sliding track door lock assembly
lower front glass
guide track lock cliplock ringlock barreloutdoor handle
manual interior
trim panel(Dr) snapping ring
glass bracket and glass gasket
rear vision mirror

B0-6
5. Tear down the interior trim panel of car door:
(a) Tear down the inner clip bolts and the inner clip.
(b) Tear down the door lamp bolts and the door lamp;
(c) Insert the screwdriver into seam between fixing clip and
interior trim panel of car door to loosen the interior trim
panel.
Notice: before using the screwdriver, wrap its head with
adhesive strap.
(d) Tear down the interior trim panel of car door.
(Dr SF)
(a) Tear down the inner clip bolts and the inner clip;
(b) Tear down the door lamp bolts and the door lamp;
(c) Tear down the electric switch and panel.
(d) Insert the screwdriver into the seam between fixing clip
and the interior trim panel of car door to loosen the
interior trim panel.
Remark: use the adhesive strap to wrap the screwdriver
head before using.
(e) Tear down the interior trim panel of car door.

SL SK SY SJ)
(a) Tear down the door lamp bolts and the door lamp;
(b) Tear down the electric switch and the panel;
(c) Tear down the screw covers and screws on the indoor
trim panel
(d) Insert the screwdriver into the seam between the fixing
clip and the interior trim panel of car door to loosen it.
Notice: use the adhesive strap to wrap the screwdriver
head before using.
(f) Tear down the interior trim panel of car door.manually operated indoor plate
inner plate of electric door (type A)
inner plate of electric door (type B)12 clips
ten clips
four sets of bolt and nut
Vehicle Body
Front Car Door
12 clips
6. Tear down the outer auchi
Loosen the clip along the edge of paneling to tear down the
outer
7. Tear down the door and window glass;
(a) Tear down the fixing bolts in the two glass sliding-
grooves.
(b) Pull up the glass to take it down.
8. Tear down the glass groove on car door.

B0-7
Change of Glass
(Dr SF)
1. Tear down the glass bracket with screwdriver or similar
tool;
2. Coat the black glue on the inside of glass bracket liner;
3. Tap the glass bracket with rubber hammer to encase it in.
(SL SK SY SJ)
1. Tear down the bolts on gear plate with pliers or similar
tool;
2. Tear down the bolts of glass bracket of car door to take
out the glass. Vehicle Body
Front Car Door170mm
Dr. SF
SL. SK. SY. SJ
9. Tear down t the lower rear glass guide track:
Tear down the bolts and guide track.
10. Tear down the lower front glass guide track;
Tear down the bolts and guide track.
11. Tear down the glass elevator:
(a) Tear down the two fixing bolts of small sliding track;
(b) Tear down the fixing bolts of three elevators (manually
operated)
Tear down the fixing bolts of four elevators. (electric)
(c) Tear down the elevator through the auxiliary hole.
12. Tear down the lock ring inside the vehicle;
Disconnect the control lever to tear down the lock ring inside
the vehicle.
13. Tear down the door lock and outdoor handle with lock
barrel;
(a) Disconnect the control lever from the outdoor handle
with lock barrel.
(b) Tear down the 3 bolts and door lock.
(c) Tear down the two bolts and outdoor handle with lock
barrel.
(d) Tear down the spring snapping ring and lock barrel.

B0-8
Assembly of Front Door
1. Coat the MP lubricant on the parts before mounting.
(a) Coat the MP lubricant on the sliding face and the gear of
glass elevator.
Notice: Do not plaster the MP lubricant on the spring of
glass elevator.
(b) Plaster the MP lubricant on the sliding face of door lock.
2. Mount the outdoor handle with lock barrel and the door
lock;
(a) Mount the lock barrel on the outdoor handle with spring
snapping ring;
(b) Use two bolts to mount the outdoor handle and the lock
barrel;
(c) Mount the door lock with three screws;
(d) Connect the outdoor handle to the control lever.
3. Mount the lock ring inside vehicle
Mount the lock ring inside of vehicle and connect the control
lever.
4. Mount the lower rear glass guide track,
5. Mount the lower front glass guide track;
6. Mount the glass elevator:
(a) Put in the elevator through the auxiliary hole;
(b) Mount on the three fixing bolts of elevator. (manually
operated)
Mount on the four fixing bolts of elevator (electric)
(c) Mount the small sliding track, and screw up the bolts of
small sliding track temporarily.
7. Mount the glass groove on car door;
8. Mount the car door and window glass;
Put the glass in the car door cavity, and then use two bolts to
fix the glass on the elevator. Vehicle Body
Front Door