Body electric system GREAT WALL DEER 2006 Workshop Manual

BE-48Body Electric System
Wiping and Washing System
In low-speed operation
Check the front brusher motor
Connect the anode lead to the terminal 2 (1) from accumulator, and
the cathode lead to terminal 3, at this time, the front wiper motor
should be in low-speed operation, otherwise change the front
brusher motor.
In high-speed operation
Connect the anode lead to the terminal 1(2) from the accumulator,
and cathode lead to terminal 3, in such condition, the front wiper
motor should be in high-speed operation.
In case the operation fails to meet the requirement, change the front
wiper motor.
in operation
stop running at the stop position
a. Run the front wiper motor at low speed and stop it at any
positions excluding the stop position by disconnect the
anode lead from the terminal 2 (1).
b. Connect the terminals 2 and 5.\
c. Connect the anode lead to the terminal 6 (4) from the
accumulator, and the cathode lead to terminal 3, check
whether the wiper motor parks at the stop position after
it running for another time, if the requirement is not
satisfied, change the front brusher motor.
Remark: items in parenthesis is for Dr and SF.
Rear brusher motor inspection
Connect the anode lead to the terminal 3 from the accumulator, and
the cathode lead to terminal 4, at this time, the wiper motor will be
in normal operation, disconnect the terminal 3, the rear wiper motor
should stop running at any position excluding the stop position.
1
2
3
4 1
2 3
4 5 61
2 3
4 5
61 2
3
4
5 6
1 2
3
4 5
6

BE-49Body Electric System
Wiping and Washing System
Connect the anode lead to terminal 3 from the accumulator, and
cathode lead with terminal 4, at this time, the wiper motor should
be in normal operation, under such condition, disconnect the
terminal 3, which is connected with terminal 1, and the anode lead
is connected to the terminal 2, in such case, the rear wiper motor
should stop running at the stop position.
In case the operation fails to satisfy the specified requirement,
change the rear wiper motor.
Inspection on Washer Motor
Connect the anode lead to the terminal 1 from the accumulator, and
the cathode lead to the terminal 2, at this time the washer motor
should be in normal operation.
Notice: this test should be finished rapidly (within 20 seconds).
In case the operation fails to meet the specified requirement, change
the washer motor.
1
21
2
3 4

BE-50Body Electric System
Central Control Lock and Electric Rocker Gear System
Central control lock and electric rocker gear system
Part Mounting position
SL SK SY SJ Dr SF
Central control lock box
Central control lock box

BE-51Body Electric System
Central Control Lock and Electric Rocker Gear System
Electric circuit diagram of central control lock
aê
pc
fuse
21
6
5
3
4 left front door switchleft front
main lock
control case of central control lock
1 2 3 4 5 6 7 8
fuse
M M M M
to generator
power lead
to left turn
lamp
to right turn
lamp
to door
lamp switch
control case of central control lock
1 2 3 4 5 6
7 8 9 10 a 12 131
6
5
7
10
132 3 12
11
central
controller box
batterylock-head lamp
battery central controller box
central control lock
switch at left front door
four doors locker
8
right front
main lock
left rear
auxiliary lockright rear
auxiliary lock

BE-52Body Electric System
Central Control Lock and Electric Rocker Gear System
Definition for connecting wire of central control lock
1. Y/V Connect the power to the cell anode on vehicle, in front of which a fuse of 15 A should be set, and
anode of 12V when the motor is started, the voltage should not less than 10V
2. B1 Unlocking output of the locking wire of the CCL actuator, and the grounding wire at the normally
central control lock: closed contact inside the relay will contact with the normally opening contact at
the common spots inside relay when unlocking with REMOTE CONTROLLER
or manually, the wire will output 12 V voltage.
3. LG locking signal of The CCL locking signal is connected to the unlocking wire of actuator of CCL,
central control lockand the normally closed contact in the interior relay is grounding wire, which will
output 12 V voltage when unlocking with REMOTE CONTROLLER or manually
and the common spots of relay contacting the normally opening contact.
4. non-connection There is no wire connected at present
5. G/R Right turn lampConnected to the anode wire of the right turn lamp on the vehicle, and it will output
12 V voltage in operation.
6. G/Y Left turn lamp Connected to the anode wire of left turn lamp on the vehicle, and it will output
12 V voltage when in operation
7. Br Negative input ofWhich is connected to the door switch and it is grounding when the door is
door switch opened (the indoor lamp will light)
8. GD ON power check cable Connected to the ON wire of the locking door( there will be 12 v voltage when
rotating the key at
ON
position.
9. Non-connection This wire is not connected temporarily
10. GD/B Lock head lamp outputThere will be 12 V voltage outputted in this wire when opening the door, and will
be powered off (no output) ten seconds later after the door is closed
12. Y/B Locking signal Connected to the locking signal wire of CCL at the left front door, and connect
to the grounding wire when in operation.
13. B Power cathode Connect to the body (grounding wire) it should be as short as possible, because
the overlong wire will produce the interference source. SF
13P
1
2
3
4
5
6
7
8
9
10
11
12
13Power anode 12 V
unlocking signal of central control lock
locking signal of central control lock
no signal
right turn lamp
left turn lamp
negative input of door switch
ON power check cable
no connection
lock head lamp
unlocking signal
locking signal
power cathode
MK
Remark: the inner switch in actuator should be
connected when the actuator is in the locking status
Remark: In case the actuator is in locking status,
connect the switch inside.
ON wire connected to key
hNOs
hj
left front CCL switch
1 2 3 4 5 6
7 8 9 10 11 12 13

BE-53Body Electric System
Central Control Lock and Electric Rocker Gear System
Electric circuit diagram of central control lock (continued)
SL SK
pv
fuse
8
76
5
4
3
left front door
main lock
right front door
main lockleft rear door
auxiliary lockright rear door
auxiliary lock
control case of central control lock
123456 78
fuse
ignition switch
ACCONST
111
10
8 91
6
4
5
3
7
12
left front main
lockright front
main lock
left rear
auxiliary lockright rear
auxiliary lock
ignition switchcontrol case of central control lock
1 2 3 4
5 6 7 8123 45
6789101112
battery door lamp switch
speed sensor central
controller box turn lamp
battery central
controller box

BE-54 Body Electric System
CCL and Electric Rocker Gear System
Electric circuit diagram of CCL
SJ Top-grade SY
fuse
ACC ONST
N
ignition switch
11
10
8 9
12745 2 61
left front main lock right front main
lockleft rear auxiliary
lockright rear auxiliary
lock
ignition switch
1 2 3 4
5 6 7 8123 45
6 7 8 9 10 11 12
battery
central controller
box
speed sensor
turn lamp
left front electric rocker gear switch
central controller box
door lamp switch

BE-55 Body Electric System
CCL and Electric Rocker Gear System
Definition of the connecting wire of CCL
1. G/R (G/W) Turn lampConnected to the anode wire of the turn lamp (right ) on vehicle, it will output 12 V voltage
when it is in operation
2. O
w/b1)Window-shutting signal outputThis wire has one second of voltage output of 12V when the car door is locking. (top SY SJ)
3. No connection
4. G (Y) Unlocking output of CCLConnected to the locking wire of actuator of CCL, and the normally closed contact in the
internal relay is the grounding wire.It will output 12 v voltage when locking with REMOTE
CONTROLLER or manually because the common spot of relay will contact the normally
opening contact.
5. Bl (G) Locking output of CCLConnected to the locking wire of actuator of CCL, and the normally closed contact inside
the internal relay is the grounding wire.It will output 12 V voltage when locking with
REMOTE CONTROLLER or manually because the common sots of relay will contact
with the normally opening contact.
6. Gr (G/B) Turn lampConnected to the anode wire of left turn lamp of vehicle, it will output 12 v Voltage when in
operation.
7. W (W) Manually controlled unlocking signalThe door lock control the locking process through the manual unlocking switch at left front
door, that is, under the locking condition, press the switch, the lock will be opened (the
switch will return to the connection situation automatically after pressing.
8. Br (R/B) Negative output of door switchConnected to the car door lamp switch, it is connected to the grounding wire (the indoor
lamp will light when opening the door.
9. R/G (G/B) Rotating speed testThe car door will lock automatically when the vehicle reaches a certain speed.
10. W(R ) ACC testConnect to the ACC wire, which will have 12 V voltage when the key is rotated to the ACC position.
11. R (R ) Power anode (12V)Connect to the anode of accumulator on vehicle, in front of which should be set the fuse
so that the voltage will be no less than 10V when the starter is in operation.
12. B(B) Power cathodeConnect to the body (grounding wire), it should be short as possible as can because the
overlong wire will produce the interference source.
SY SJ
1
2
3
4
5 6
7
8
9
10
11
12left turning light
manual switch locking signal

closing window output
none
door switch negative input
speed test
ACC test
power anode 12V
remote control opening lock output
power cathode
remote control closing lock output12V
W
K door switchK
M
M
MM
Items in the parenthesis is for SY diesel model
Items with
are configuration for SJ and top SY

BE-56 Body Electric System
CCL and Electric Rocker Gear System
Diagram of electric rocker gear
Dr
main
auxiliary
12
34 512
34 5
12
34 512
345 mainauxiliary
main auxiliary
12
345 12
34 5
12
34 51
2
1 2 3 4 5
6 7 8 9 10 1
2
1
2
43
5
21
345
1 2
21
3 4
R
N2
34 5
21
2 1
34
5
2 1
34
5
1
2 12
345
electric window relay
STON ACC auxiliary
falling
stop
raising
main
falling
stop
raising
auxiliary
main
falling
stop
raising falling
stop
raising
auxiliary
main
falling
raising
falling
stop
raising
right rear
left rear
right front
left
front
inhibitor switch
falling
stop
raisingstop
right front door switch
left front door switch
battery
fuseignition switchignition switch electric rocker gear
left rear door switch
left rear door switch

BE-57 Body Electric System
CCL and Electric Rocker Gear System
SF
right rear door switch
1
2
3
45
left rear door switch
1
2
345
right front door switch
1
2
345
left front door switch
123 456
7 8 9 10 111213
ignition switch
1 2 3 4 5
6 7
U9 10electric rocker gear
1
2 21
52
3 1
4
21
25
1
4 3
1
2
52
1
4 3
21
12
7
13 1
342
electric window relay
ST ON ACC
battery fuse ignition switch
right rear
left rear
right
front
left
front
control lock
12
11
inhibitor switch
Diagram of electric rocker gear