plugs GREAT WALL DEER 2006 Service Manual

IN-4
Overall Repairing Description
1. Keep the vehicle clean and prevent it from
damage with guard plate, seat and floor cover
cloth.
2. Put down the dismantled parts in order during
the dismantle process so as to facilitate the re-
assembly
3. Observe the following items:
a) Disconnect the cable cathode from the
accumulator terminal before the electric
operation;.
b) Disconnect the cable from the cathode
connected to the vehicle body when check-
ing or repairing the accumulator where
necessary.
c) In order to avoid the damage of terminal
post of accumulator, loose the bolts first,
then pull up the cable vertically when
dismantling, don
t wring it or prize it.
d) Clean the terminal posts of the accumula-
tor with dishcloth, and do not scrape them
with file or other similar tools to avoid
damage.e) Mount the cable terminal on the post with loosened nut, then
fasten the nut. donít tap the terminal onto the post with
hammer.
f) Be sure to check whether the cover of positive terminal (+) is
well located or not.
4. Check all hoses and wire plugs to verify whether they are
connected solidly and correctly.
5. Parts that cannot be reused after being used.
a) The following parts should be changed with new one regularly:
split pin, sealing washer, O-ring and oil seal, etc.
b) parts that cannot be reused after being used is marked with

 in the element figure.
6. Pre-coated parts
The pre-coated parts including the bolt and nut are coated with
locking seal glue in factory.
a) In case the pre-coated parts are moved due to its fastening,
loosening or other causes, they must be coated again with the
specified seal glue.
b) Coating procedure of pre-coated parts
1) Clear away the former seal glue from the screw thread of
the said parts.
2) Dry the parts with compressed air.
3) Coat the screw thread of the parts with the specified
locking seal glue.
c) The pre-coated parts are marked with the
 in element
figure.
7. When necessary, sealing agent or sealing ring to prevent the
leakage.
8. Each specification shall be followed strictly. And the torque
spanners should be used.
9. Determine the necessity of using the special service tools (SST)
or special service materials (SSM) according to the real situation.
SST and SSM must be used where necessary and the repairing
should be in accordance with the repairing approach. SST list
and SSM list are attached to this manual.
10. Be sure to check whether the rated current of the new fuse is
correct when changing the fuse. The fuse rated current should
not larger than that of securing fitting and the fuse of smaller
rated current must not be used.
11. Be careful to hang or support the vehicle on the suitable place
when propping up or raising it.
a) In case prop up the vehicle at the front or back part, the wheels
must be blocked to guarantee the safety work. Introduction
Overall Repairing Rescription
tighten seal glue

TF-7Transfer Box
Disassembly and Mount of Transfer Box
Disassembly and Mount of Transfer Box
1. Transfer Box Disassembly
(a) Drive the vehicle on the lifting jack.
(b) Locate the gear of transfer box at the neutral
position, shift the transfer box to the 2H and
extinguish the engine.
(c) Disconnect the cell cathode.
(d) Lift the vehicle.
(e) Put down an oil disc under the transfer box, tear
down the oil drain plug and oil filling plug of the
transfer to drain all the lubricant up, then re-
mount the two plugs.
(f) Disconnect all wires and wire harnesses that
connected with the transfer box.
(g) Take apart the hose on the venting valve of
transfer shaft.
(h) Disconnect the linkage of the front drive shaft
with the front flange of the transfer box.
(i) Disconnect the linkage of the rear drive shaft
with the rear flange of the transfer box.
(j) Raise the transfer box up with the jack.Notice: The transfer box shall be guaranteed to
support by the lifting jack before tearing down
the sets of bolt and nut that connected with the
transfer box and gearbox. The transfer box is
not allowed to hang directly on the gearbox
through spline because such operation will
damage the transfer box parts.
(l) Tear down the connecting nuts between the
transfer box and gearbox and take down the
transfer box.
(m) Move the transfer box backward directly until
the linkage between the input shaft of transfer
box and the gearbox spline.
(n) Put down the lifting jack of the transfer box, and
(o) Tear down the gasket between the transfer box
and gearbox. Clean the gasket or glue on the
coupling face of front body of transfer box with
rear body of the gearbox. Take notice not to
damage the coupling face.
1234
5 6 7
8
9
1. input shaft
2. front frame of transfer box
3. rear cover of transfer box
4. flange
5. front output fork flange
6. venting valve
7. gasket
8. rear body of gearbox
9. bolt

TF-9
5 4
3
1
6 2
1. rear body of transfer box
2. flange
3. oil seal
1. sensor bracket
2. bolt
3. speed sensor
4. o-ring
5. sensor assembly
6. bolt
7. gasket
8. rear body of transfer box2 1
5 3
4
4
6
7
8
Transfer Box
Disassembly of Transfer Box
4. gasket
5. nut
6. oil plug
Disassembly of Transfer Box
1. Brief instruction
In case the transfer box is required to be repaired for the
damaged specific element, it shall be taken apart to the degree
on which the damaged element is taken out. And the parts
taken apart from the transfer box, if it doesnít include the
damage element, can exist in the form of sub-assembly or
group instead the individual form, otherwise, the parts will be
taken apart individually.
2. Transfer Box Disassembly
Put the transfer box on the worktable and ensure the rear part
or the rear cover faces upward. Put the wooden block under the
front part of transfer box to keep the transfer box stands
horizontally. The disassembly process is as follows:
(a) Fasten the flange with the torque arm typed T-13-54-
002, screw off the nut to take down the gasket, then take
apart the flange and oil seal.
(b) Take down the two oil plugs from the transfer box body.
As for the electric gearshift transfer box, tear down the
electric shifting element according to the following
disassembly approach:
(a) Tear down the three bolts, gaskets, sensor and clip for
wire harness.
(b) Tear down the sensor assembly and take apart the O-
ring.
(c) Tear down the motor assembly.

TF-23
5 4
3
1
6 2
Transfer Box
Transfer Box Assembly
1. transfer box rear body
2. flange
3. oil seal
4. gasket
5. nut
6. oil plug
13. Flange assembly
The parts mount process is as follows:
(a) Encase the two oil plugs in the rear cover.
(b) Encase the flange, sealing ring and gasket, and then
screw up the nuts.
Fastening torque
(203
244)N
m

BE-36Body Electric System
Combination Instrument
Normal indicating range of combination instrument indicator
Speedometer
Real speed Km/h
Displayed speedKm/h
20 40 60 80 100 120 140 160
20
340
056005
Tachometer SY SL
800510005120061400716008
750 1000 2000 3000 4000 5000 6000
750
-10+201000-10+502000
120 3000
150 4000
200 5000
250 6000
300 Real rotating
speedr/min
Displayed rotating
speedr/min
Tachometer Dr SL SK SF
1000 2000 3000 4000 5000 6000 7000
1000
100 2000
200 3000
150 4000
200 5000
250 6000
300 7000
350 Real rotating
speedr/min
Displayed rotating
speedr/min
c. The inaccuracy display of tachometer is usually caused by the interior failures of tachometer, in such situation,
change the combination directly. As for the good-bad shift or out-operation of tachometer, the failures can be judged
according to the following approaches:
1) Start the vehicle, then check the voltage of signal input of tachometer (wire harness with multi-meter, the
voltage should be 6 V or so.
2) In case there is no signal voltage, check the power supply system of the whole vehicle to remove the failures
in circuit.
3) The plugs of wire harness is only allowed to be inserted in the combination instruments under the condition
that the signal voltage is normal, and the instrument is in normal operation.
4) Where the instrument is in abnormal operation, such trouble is caused by the failure of combination
instruments, in such case, change the combination instrument directly.
d. Troubles of fuel gauge and water thermometer
1) In case the instrument indicator points to the large number after it is powered, disconnect the sensor from the
plugging elements of wire harness before judging such kinds of troubles, if the indicator is still at large number,
it can be make a judgment that the trouble is caused by the interior failure of instrument, in such case, change
the combination instrument directly; if the indicator returns to the small number, according to which it can be
judged that the trouble is caused by the sensor failure, therefore, change the sensor directly.
2) where the instrument indicator stands still, such trouble may be caused by three causes probably, interior failure
of sensor, plugging elements of wire harness or interior failure of instrument; the inspection may be conducted
according to the following approaches: disconnect the plugging elements of wire harness from that of sensor,
grounding the wire at the sensor end; in such condition, the indicator should move upwardly to the largest
number; if such phenomena occurs, it can show the trouble is caused by the interior failure of sensor, in such
case, change the sensor directly; if the instrument indicator is still immobilized after it is powered, it can be
judged that the trouble is caused by the interior failure of instrument under the condition that the wire harness
and plugging elements are normal, in such case, change the combination instrument directly.
Fuel gauge Dr SF SY
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

5
4+3
Fuel gauge SJ
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
110 38 7

12
4
2
Fuel gauge SL SK
Displayed oil
volume
Reference
resistance

Permitted
error
E 1/2 F
120 45 17

10
10
10

BE-66
Mount of bass speaker and VCD
(a) bass speaker
Connect the audio output wires of bass speaker with the sockets in bass speaker correspondingly according
to the wire color (red plugging element should be plugged in red socket, yellow plugging element in white
socket, the grounding wire (black), power wire (yellow) and signal wire (blue) should be fixed at the
corresponding positions (GND
12V
REM) on bass speaker tightly.
(b) multi-disc VCD
The feed cables of VCD main device should be connected as marked, when connecting the plugging element
of wire harness of video camera (CAM) with the plugs on main device (CAM), notice should be taken on the
two arrow marks so as to prevent the plugging element damage; The audio output wire plugging elements (red
and yellow plugs) of bass speaker should be connected with the red and white sockets of mainframe (AV OUT);
the plugging elements of TV receiving input wire of amplifier should be connected with either of the plugging
elements(AV AN) of the mainframe; the plugging element (black and white ACC) of anode wire of power
supply should be connected with the red socket (ACC) of mainframe wire harness; grounding wire plugging
element (black GND) should connect with the black socket of mainframe wire harness; the plugs of audio input
wire of deci-disc data converter should be connected with the red and white socket on mainframe according
to the plugs color (the plugs (red, white CD OUT) of audio input wire of eight-disc box should be connected
with the red, white socket (CD IN) on mainframe according to the plug color, the yellow power wire plugging
element (BATT) should be connected with the yellow power wire socket (BATT) on mainframe, the electric
aerial, plugging elements of control wire of function amplifier should be connected with the electric aerial
(CTL), socket of control line of function amplifier on mainframe. After completing the connection of plugging
elements, wrap the connecting position with adhesive strap in order to prevent those plugging elements from
peeling off, the plugging element of feed cable of TV receiving aerial can connect with any two of the four
holes on amplifier, meanwhile, turn on the switch (with a red indicating lamp) of amplifier when watching the
TV play. When mounting the VCD mainframe, push the wire harness innermost as can as possible so that there
is spacious room for mainframe, then push in the mainframe, notice should be taken not to damage the wire
harness. Fasten the mainframe to the degree that it cannot be pull out by hand after assembling, if it cannot be
clamped tightly, prize out the two clips on the inner sleeve, then fasten the mainframe, and mount on the
external decoration frame finally. When disassembling the mainframe, tear down the external decoration
frame first, then insert the special key into the open grooves at two sides to pull out the mainframe.Body Electric System
Acoustical Equipment System