seat adjustment GREAT WALL DEER 2006 Service Manual

Preface
With the increase of automobile demand in China, our automobile industry also experiences a rapid
development. The trucks including SUV, manufactured by Great Wall Motor Co., Ltd, which are sold all over
China, are in the leading place in terms of their sales volume, in order to satisfy the demands of various maintain-
ing staff, technicians and managing staff of Changcheng Co., Ltd, we compile this maintenance manual accord-
ing to the latest technological data. This manual covers six vehicle models including Deer, Safe, Sailor, Sing, So
Cool and Pegasus, its main content includes:
Part I is general introduction, which introduces the application index of this manual.
Part II introduces the chassis system, which mainly includes the technologies of dismantle, inspection,
adjustment, repairing, assembly and mount of the clutch, gear box, transfer box, drive shaft, suspension system
and automobile axle, braking system and steering system, etc. each operation approach is illustrated with figure,
which not only presents the maintenance procedure, but also clearly describes the technical requirements and
application limit.
Part III introduces the electric system and air-conditioning system of the automobile body, which mainly
covers such items as the location and content of protective box, power supply system, starting system, lighting
system, combination instrument, backup radar system, wiping and washing system, center control locking and
power window system, acoustical equipment system, full wire harness and air-conditioning system, etc. Electric-
ity diagrams for those electric systems are given in this manual so as to facilitate the maintaining technicians to
find out the problem easily and quickly.
Part IV introduces the external and internal body decoration, which mainly covers the dismantling, inspect-
ing and assembling requirements of the engine cover, front and rear doors, adhesive strip of body collision
avoidance, wheel shield, wrapping angle of wheel-shield and exterior trim panel, front and rear windshields,
side-window glass, rear-door glass, rear platform of cargo compartment, rear door, instrument panel, safety belt,
seat, tail-fin, luggage rack, and reserve tire bracket etc. The dimensions of vehicle body and frame are also given
to maintaining staff for reference during their repairing.
During the narrations of each part, items such as troubleshooting, maintenance notice, maintenance data
and application limit, fastening torques of bolts and nuts for special purpose, SST, SSM and lubricant materials
and so on are also introduced. Various maintenance data are briefed in attachment for reference.
Altogether, this manual is comprehensive in content, visual in illustration, clarifying in requirement and
plain in language. It can be referred by the maintaining staff, technicians and professional managing staff.
Even though we try our best to compile this manual in a strict earnest manner, we cannot guarantee that all
contents in this manual are correct. Therefore, users shall not put forward any claim with Great Wall Company
according to this manual; we are not in the position to hold the responsibility for the loss caused by usage of this
manual. Due to our limited knowledge, it is unavoidable to find error in this manual, any criticism and correction
from you is welcomed.
The final explanation power for this manual is subject to Great Wall Motor Co., Ltd
Compiler
May 2006

SA-13
3. Mount the front wheel hub on the steering knuckle.
Coat a little lubricant at the position of the steering knuckle
where the oil seal locates, mount the front wheel hub and front
brake disc on the steering knuckle, and then mount on the stop
washer.
4. Preload adjustment
(a) Mount on the lock nut and screw up according to the
specified torque.
Fastening torque
(130-150)N
m
(b) Run the front wheel hub about 1/4-1/3 of circle, and
combine it with the bearing seat.
(c) Loosen the locking nut to ensure the front brake disc run
freely, and then screw up the nuts to the specified torque.
Fastening torque
(25-35)N
m
(d) Hook the front wheel hub with the spring-tension meter
and pull the spring-tension meter slowly in the tangential
direction of this spot.
The reasonable range of tension force: (16-33)N.
Remark: if the tension force is larger or smaller of the reason-
able range, screw up the nuts again until the tension force falls
within the reasonable range.
(e) Measure the bouncing value of the front brake disc,
which should not be larger than 0.11mm.
5. Mount on the lock cover and the split pin
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-91
9. Mount on the differential bearing cover:
(a) Align the assembly marks on differential bearing cover
and the speed reducer housing, and press down the
differential bearing by hand.
(b) Mount on the double-eared stop washer and the hex nut.
10. Adjust the clearance between the driving bevel gear and
the axle driven bevel gear
(a) Screw up the hex nuts connecting the differential bearing
cover to the specified torque.
Tightening moment
(80-110)N
m
(b) Attach the measuring meter seat on the face of speed
reducer housing with the measuring head touching the
teeth face, run the axle driven bevel gear with hand to
measure the teeth engagement clearance, and then com-
pare it with the clearance value in step (d) to decide the
order of the adjusting ring tightening according to the
values.
(c) Adjust and screw up the adjusting rings with SST.
Tightening moment
(115-135)N
m
(d) Check the engagement clearance again until the clear-
ance value of the three spots evenly locates on the
circumference of axle driven bevel gear. Otherwise,
adjusting ring adjustment is suggested.
Engagement clearance
(0.13-0.25)mm
Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer)