transmission oil GREAT WALL DEER 2006 Service Manual

MT-25Transmission
Output Shaft Assembly(Assembly of Output Shaft Assembly)
Assembly of output shaft assembly
1. Assembly of synchronizer
(a) Insert the synchronizer hub and sliding block into the gear
sleeve.
(b) Install the spring expansion ring under the sliding block.
Note:The openings of spring expansion ring should be
staggered during installation .
2. Install the gear components of 3rd gear and synchronizer
of 3rd and 4th gear on the output shaft.
(a) Smear the gear oil on the shaft and the needle bearing of
3rd gear.
(b) Put the synchronized ring on the components of gear of 3rd
gear, and align the notch of synchronized ring and sliding
block.
(c) Install the needle bearing into gear components of 3rd gear.
(d) Assembly the gear components of 3rd gear and synchro-
nizer of 3rd and 4th gear with pressing machine.
3. Assembly of snap ring for shaft
To choose one snap ring which make the axial clearance be
Min, and install it on the shaft.
3/4 gear posititon
1/2gear posititon
front
front side

MT-26Transmission
Output Shaft Assembly(Assembly of Output Shaft Assembly)
Standard clearance:
For the transmission made by Shang Chi
(0.15
0.33)mm
For the transmission made by Tang Chi:
(0.09
0.33)mm
5. Assembly for the gear components of 2nd and
synchronizer of 1st and 2nd gear
(a) Smear the gear oil on the needle bearing of gear of 2nd
gear.
(b) Put the synchronized ring on the gear,and align the notch
and shift key.
(c) Install the needle bearing into the gear components of 2nd
gear.
(d) Assembly the gear components of 2nd gear and meshing
sleeve of synchronzer of 1st and 2nd gear with pressing
machine.
6. Check the axial clearance of gear components of 2nd
gear
Measure the axial clearance of gear components of 2nd gear
with feeler gauge.
Standard clearance:
For the transmission made by Shang Chi:(0.15
0.33)mm
For the transmission made by Tang Chi:(0.09
0.33)mm
7. Assembly the locking ball and gear components of 1st
gear
(a) Install the locking ball into the shaft.

MT-27Transmissio
Output Shaft Assembly(Assembly of Output Shaft Assembly)
SST
SST
(b) Smear the gear oil on the needle bearing of gear of 1st gear.
(c) Assembly the gear components of 1st gear,synchronized
ring,needle bearing and sleeve of gear of 1st gear.
(d) Install the assembly on the output shaft,and align the notch
of synchronized ring and sliding block .
(e) Turn the sleeve of 1st gear shaft to align the it with the
locking ball.
8. Installation for rear bearing of output shaft
Fix the bearing of output shaft to the output shaft with SST and
pressing machine, make the notch of locking ring of output
shaft rear bearing expose to the tail.
Remark: Hold the sleeve of gear of 1st gear and don
t let it fall
off.
9. Install the gear of 5th gear
Fix the gear of 5th gear with SST and pressing machine.
10. Assembly the snap ring of shaft
(a) To choose one snap ring which make the axial clearance
be Min, and install it on the shaft.
Max clearance
0.1mm

(b) Knock the snap ring of shaft of 5th gear tightly with
screwdriver and hammer.
11. Measure the axial clearance of gear of 1st gear
Measure the axial clearance of gear of 1st gear with feeler
gauge
Standard clearance:

For the transmission made by Shang Chi:(0.15
0.33)mm
For the transmission made by Tang Chi:(0.09
0.33)mm

TF-2Transfer Box
Notice
Notice
Notice on transfer box disassembly and assembly
Notice shall be taken on the soft handling of the parts (coupling face in particular) during the process of
transfer box disassembly to avoid the collision; each parts shall put down in order so as to avoid of missing
or mistaking.
Notice shall, during assembly process, not only on the aforesaid items, but also on the following items:
1. Wash all parts and fittings before assembly (rubber element and washer excluded).
2. Oil seal, clip for shaft and spring pin of various kinds shall not be reused.
3. Lubricating oil is required to coat on the various friction surface and lubricant on lips of various oil seal.
4. Rolling body is not allowed to use for pressure transmission when mounting various bearings.
5. Lip-type oil seal is not allowed to mount slantwise.
6. The openness on the two sides of spring collar shall not be coupled face-to-face when assembling the
component elements of synchronizer. And
7. No parts is allowed the lubricant leakage and penetration when the transfer box locates at the working
location.

TF-11
5. Tear down the Chain drive system
Take apart the following parts from the transfer box housing
assembly.
(a) Take apart the snapping ring and washer from the front
output shaft.
(b) Take apart the driving chain sprocket, driven chain
sprocket and drive chain together from the two output
shafts.
(c) Separate the chain sprocket from the chain.
12
345
6 7
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
12 34
5
6 7
6. Oil pump assembly
Take apart the shaft and pump assembly, pipe clip, oil pipe and
filter from the remaining transfer box housing assembly.
1
2
7
6 3
4
5
8 1. deceleration gear hub
2. inserted face of Shift
toggle fork
3. plastic sleeve
4. contact roller
5. pin
6. pin, contact roller and sleeve assembly
7. deceleration shift toggle fork
8. deceleration shift toggle fork assembly7. Deceleration shifting element disassembly
Tear down the following parts from the remaining transfer box
housing assembly.
(a) Take apart the deceleration hub, and deceleration shift
fork assembly from the housing.
(b) Take apart two plastic inserted faces from the decelera-
tion shift fork assembly
(c) Disassembly the deceleration shift fork assembly only if
it were broken.Cut the plastic cover,and take out the pin
and truckle. Transfer Box
Disassembly of Transfer Box
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
5. snapping ring
6. transmission chain
7. front output shaft5. snapping ring
6. transmission chain
7. front output shaft

PR-6Drive Shaft
Drive Shaft
3. Take apart the drive shaft from the gearbox.
(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox to prevent the oil leakage
Front axle drive shaft
4. Tear down the front universal joint flange fork of the front
drive shaft.
(a) Hang he front end of the front axle drive shaft.
(b) Label the assembly mark on the flange
(c) Take apart the four sets of bolt and nut.
5. Disconnect the rear universal joint flange fork from the
front axel drive shaft along the transmission path.
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
Drive shaft disassembly
1. Separation of the rear joint of the rear axle drive shaft
from the front joint of rear axle drive shaft
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
2. Take apart the center support bearing from the front joint
of the rear axle drive shaft.
(a) Loosen the riveted nut by chiseling with a chisel and
hammer.
SST
assembly mark
assembly mark