fuses GREAT WALL FLORID 2008 Service Manual

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual6
2. Inspection procedures for related fuses or fuses in re- Inspection procedures for related fuses or fuses in re-Inspection procedures for related fuses or fuses in re-
lay boxes. Inspect the battery for damage, the battery's
charging state, cleanness, and tightening with the
connectors.
Before changing a fuse, make sure to check if the fuse's cur-
rent rating meets the required standards. You must not use a
fuse with a current rate that is higher or lower than required
standards.
Same current rating
3. Binding wire harness connectors.
(a) When disconnecting the connections, first press the two
ends of the connectors together, then loosen the lock
and press the lock pawl to release the connector.
(b) When disconnecting the connector, do not pull on its
wire harness. Grasp the joint directly.
(c) Check if the joint is deformed, damaged, or port lost
before connecting the connector.
(d) The connector is not successfully connected until it
makes a click sound.
4. Wire harness connector inspection.
(a) Check while connecting the connectors.
Squeeze both ends of the connectors to make sure it is com-
pletely plugged in and tightly locked.
(b) Check when disconnecting the connectors.
Check by lightly pulling the wire harness behind the connec-
tor's joint. Look for any unconnected or dropped terminals,
loose clamps, or broken wires.
Visually inspect for instances of corrosion, metal fragments,
oddities, and water, as well as bending, rust, overheating,
pollution or deformed terminals, etc.
(c) Check the contact pressure of the terminals.
Prepare a plug that matches the connector's port, plug it into
the socket, then check for the proper rate of tension after
they are fully engaged.
Loosen crimp
Core
Deformed terminal
Pull lightly
The terminal is similar to a plug
Incorrect

Downloaded from www.Manualslib.com manuals search engine 201Electrical Accessories
1. This player is used on vehicles with a 12 V battery and negative ground. If this player is to be installed
on a vehicle with a 24 V battery, please install voltage reduction equipment.
2. To avoid short circuiting the electrical system, cut off the battery negative end's connection wire before
installation.
3. Please arrange the connection wires at fixed locations, as to make sure they will not make contact
with any portable parts, such as the parking brake control mechanism assembly, gear lever, the seat's
fixed track, and so on. Please do not arrange the wires in a heat source area, like near the discharge
outlet of the heater, etc. Otherwise the heat source will cause the insulating layer to melt or wear out,
and then lead to a short circuit between the connection wire and the veh\
icle body.
4. Do not put the power cord through the mounting hole into the engine box and then connect it to the
battery. Otherwise it might damage the power cord and then lead to a short circuit between the power
cord and the vehicle body.
5. When changing the fuse, please use the specified 15 A fuse. Fuses with an unmatched size will lead
to abnormal operation, and even damage the player or cause a fire hazard\
.
6. Please do not share the player's power supply with other equipment, otherwise it might lead to a
malfunction due to overloading.
7. Please wrap up the exposed places of the wire with insulating cement to \
avoid short circuiting.
8. Bind up all the connection wires well to avoid any connecting term inal touching the player or other
mental parts of the vehicle body and leading to a short circuit.
9. When switching the player's power on, the external connection amplifier's controlling signal will output
through the lead wire P.CONT. If the player is connected with an external connection amplifier, please
do not connect the lead wire P.CONT to the amplifier's supply terminal, otherwise it will cause a
malfunction.
10. The player's outputting terminal must not be grounded, otherwise the amplifier may burn out. Please
do not use a 3-wire type speaker system which shares the ground cable. Please do not connect the
speaker wire to the vehicle body.
11. The maximum rated power of the speaker connected to this player is 50 W , resistance value is 4 Ω.
Control wire connection areas of importance