brake GREAT WALL PEGASUS 2006 Owners Manual

BE-73
SY SJ
1 grounding wire
2 wire harness at right front door
3 warm air motor
4 connected to wire harness at right front door
5 control case of central control lock
6 electric aerial
7 heat-sensitive resistance
8 speed-adjusting resistance
9 connected to housing wire harness
10 connected to housing wire harness
11 A/C switch
12 air-volume switch
13 ashtray luminous lamp
14 grounding wire
15 ECU
16 CD device
17 CD device
18 cigarette lighter
19 cigarette lighter grounding wire
20 cigarette lighter luminous lamp
21 combined switch
22 fog lamp switch
23 dual flasher switch
24 rear defroster switch
25 rear brush switch
26 rear washer switch27 combination instrument
28 combination instrument
29 stop lamp switch
30 roof wire harness
31 connected to housing wire harness
32 connected to housing wire harness
33 connected to housing wire harness
34 connected to wire harness at left front door
35 connected to wire harness at left front door
36 connected to wire harness at left front door
37 protective box
38 rear defrost relay
39 connected to wire harness of rear air-conditioner
40 grounding wire
41 parking brake switch
42 connected to chassis wire harness
43 wire harness at right rear door
44 right front door lamp switch
45 right rear loudspeaker
46 rear washer motor
47 connected to wire harness at tail door
48 left front door lamp switch
49 wire harness at left rear door
50 left rear loudspeaker
51 standby power seat
1
2
3
4
5
6
7
8
9
101112
13
14
15
1617
181920
21 22232425262728
29
30
31
32
3334
35
36
37
38
39
4041 4243 444546
47
48495051
Cab wire harness (continued)
Body Electric System
Wire Harness Distribution

B0-59Body
Safety Belt
Safety belt
1. Driving test (in the security place);
(a) Fix the safety belt of the front seat.
(b) Drive the vehicle at the speed of 16 km/h and brake it
suddenly;
(c) Check the safety belt, which should be lock tightly
without expansion.
Remark: it is required to tear down the mechanism
fittings of the safety belt to make the following static load
test at the security place, in addition, moderate inspection
for the new safety belt should be conducted before
mounting no matter when the new safety belt fittings is
needed to mount.
2. Static test

a) Tear down the lock-type expansion fittings;
(b) Tilt the expansion fittings slowly;
(c) Check the expansion of safety belt, which should be
pulled out when the tilt angle is no more than 15 but not
be pulled out when the tilt angle is more than 45
.
If the requirement is not met, change the safety belt fittings.
Two-point safety belt
(manually operated)
(a) Adjust the safety belt to the moderate length;
(b) Exert the stable load on the belt;
(c) Check whether the safety belt is elongated or not, in such
case, the belt should not be elongated.

A-2
Clutch
Specification
Item Specification
Fastening torque for clutch tube on master cylinder
Fastening torque for clutch tube on wheel-brake cylinder
Fastening torque for clutch pressure plate160
190-200
5-15
0.3
0.8
0.2
0.6
5
Max misplacement
0.5 Pedal height (calculated from front wall
Pedal free stroke
Min depth of clutch-facing rivet
Max radial swing difference of clutch rib
Max radial swing difference of flywheel
Max width of wear of diaphragm spring
Max width of wear of diaphragm spring
Alignment degree of diaphragm spring endApplicable vehicle model
Dr SF
SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Torsion moment
Fastening location (N*m)
15-17
15-17
30 Applicable Vehicle model
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,
Lubricant Type
GL-5 SAE80W/90
Torsion moment of relative connecting elements
Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)
Unit
ãã Specification of Maintenance and Up-Keeping
Clutch and Gearbox
Locating screw of fork axle at first and second gear
Locating screw of yoke block
Screw on baffle of rear bearing of output shaft
Screw of reverse idler shaft
Bolt of gearshift cover
Bolt of front cover
Bolt of rear body
Bolt of clutch shell
Bolt of locating spring13
17
15
20
17
22
17
20
15
20
15
20
30
45
30
45
17
22 Fastening location N*m

A-5
Torsion moment
Fastening location Applicable vehicle model N*m
Limit bolt of steering knuckle
U-type fixing bolt
Bolt of spring pin of rear plate and shackle
Central bolt of rear steel plate spring
Connecting bolt of rear vibration damper and rear axle
Connecting bolt of front vibration damper and lower swing arm
Connecting bolt of rear vibration damper and frame
Connecting bolt of rear vibration damper and lower swing arm
Fixing bolt of pedestal arm of torsion rod spring
Locking nut of torsion rod spring
Fixing bolt at two ends of transverse stabilizer rod
Fixing bolt of transverse stabilizer rod bracket
Connection bolt of guide lever and lower arm
Fixing nut at front end of guide lever
Axial fixing nut of front suspension and lower arm
Axial fixing nut of lower arm of front suspension
Connecting nut of steering knuckle and upper ball stud
Connecting bolt of steering knuckle and lower ball stud90
10
110
10
90
10
50
5
64
5
25
5
25
5
137
10
83
5
83
5
23
3
29
5
23
3
25
5
96
10
150
10
96
10
178
15
226
25
196
10
226
025
210025
110
10
142
10
142
10 SJ
Dr SL SK SY SJ
Dr SL SK SY SJ
SL SK SY SJ
SF
SL SK SY SJ
SL SK SY SJ
SF
SL SK SY SJ
SL SK SY SJ
Dr
SL SK SY SJ
Dr SF
SL SK SY SJ
Dr SF SL SK SY
Dr
Dr SL SK SY SJ
SF
Dr
SF
SL SK SY
SJ
Dr SL SK SY SJ
SF
Dr SF SL SK SY SJ
Braking system
specification
Item Applicable vehicle model specification
Pedal height
Free stroke of pedal
Stroke of operating lever of parking brake160mm
190-200mm
3-6mm
9-10

7-9
Dr SF
SL SK SY SJ
Dr SL SK SF SY SJ
Dr
SL SK SY
torsion moment
Fastening location Applicable vehicle model N*m
Brake oil pipeDr SF
SL SK SY SJ18
2
19
1
Specification of Maintenance and Up-Keeping
Braking System

A-6
Torsion moment
Fastening location Applicable vehicle model N*m
Fixing nut of steering wheel
Connecting nut of steering ger and swing arm
Fixing bolt of steering driven arm
Fixing bolt of steering gear
Connecting nut of steering drag rod and swing arm of
steering gear
Connecting nut of steering drag rod and steering driven
arm
Connecting nut of steering drag rod and front brake
Steering limit boltDr SF
SL SK SY SJ
Dr SF
Dr
SF
SL SK SY
SJ
Dr
SF
SL SK SY
SJ
Dr SF
Dr
SF
Dr SF
SJ50
5
30
2
245
25
80
10
142
10
83
10
78
10
96
10
145
10
96
10
78
10
91
10
91
10
59
5
91
10
90
10
Steering system
Specification
Item Applicable vehicle model Specification
Max play of steering wheel
Tension degree of driving belt:
When f=98N New belt
Old beltDr SF
Dr SL SK SF SY SJ
Dr SL SK SF SY SJ6

5-7mm
7-9mm
Specification of Maintenance and Up-Keeping
Steering System

B-3
Application position
Front axle
Rear axle
2WD 4WD
3916011

3916012
3916013
3916014
3916015
3916016
3916017
3916018
3916019
3916020 Press fitting tool of up-
per arm liner
Disassembling and as-
sembling tools of wheel
brake cylinder of front
brake caliper
Disassembling tool of
front drive shaft bearing
Pneumatic caliper of
outer sleeve of front drive
shaft
Press fitting casing of
front drive shaft bearing
Disassembling tool of
main teeth oil seal
Press fitting tool of main
teeth oil seal
Disassembling tool of
long semi-axis
Electric cutch tester
Disassembling tool of oil
seal and needle bearingOil seal of long semi-
axis of front axle
Inner oil seal of rear axle
shaft
Needle bearing of long
semi-axis
SST Special tool
Diagram Tool Name tool number Remark
SST Special Tool
Special Service Tool