tow GREAT WALL PEGASUS 2006 Service Manual

SA-80
Dismantle of Rear half Axle Shaft
1. Tear down the wheels.
2. Tear down the rear brake drum.
3. Tear down the grab end of the bracing wire of hand brake
from the rear brake.
4. Tear down the half-shaft and the rear brake assembly
from the rear axle housing.
5. Tear down the flat steel retainer ring for shaft from the
half-shaft;
Tear down the flat steel retainer ring for shaft with the ring
calipers.
6. Tear down the half-shaft:
Put down a wooden plate on the flat ground, and thrust the end
of spline of half-shaft and rear brake assembly toward the
wooden plate to separate the shaft and the rear brake assembly.
Inspection on and repairing of half-shaft parts
1. Check the wear, damage and swing difference half-shaft
and the flange.
Max shaft run-out: 2 mm
Max flange run-out: 0.2 mm
In case the half-shaft is damaged, or wearied or the measuring
value of the swing difference is excessive, change the half-
shaft.
2. Check he oil seal of rear wheel bearing:
Check to see whether there is wear or damage, and change the
oil seal if necessary.
3. The disassembly of the outer oil seal of rear wheel
bearing;
Tear down the outer oil seal of rear wheel bearing with SST. Suspension System and Automobile Axle (rear)
Rear Half Axle Shaft

BR-11Brake System
Vacuum Booster
Inspection on Vacuum booster parts
Operation for one-way valve inspection
(Gasoline engine)
(a) Tear down the one-way valve;
(b) Check the air to see whether it flows from the vacuum
booster side toward the engine side.
(c) Check the air, change the one-way valve if the air flows
from the side of engine toward the vacuum booster.
(d) Mount the one-way valve in the right place.
(a) Tear down the one-way valve from the vacuum pipe.
(b) Check the air to see whether it flows from the side of
vacuum room to the hose.
(c) Check the air, and change the one-way valve if the air
flows to the hose to the vacuum room.
air
engine side booster side
air airless
air
hose side vacuum side
airairless
Mount of Vacuum Booster
1. Adjust the length of vacuum booster pushrod:
(a) Mount the sealing washer on the master cylinder;
(b) Put SST on the sealing washer and descend the pin rod
until it contact lightly the piston with its top;
(c) Put top of SST downward ,and mount it on the vacuum
booster.
(d) Check the clearance between the vacuum booster pushrod
and the head of pin on SST.
(e) Adjust the length of vacuum booster pushrod until the
pushrod touches the pinhead.
2. Mount the vacuum booster, sealing washer and Ushaped
clip head.
(a) Mount the vacuum booster and sealing washer.
(b) Mount the U-shaped clip head.
(c) Mount and tighten the assembling nuts of vacuum booster.
3. Connect the U-shaped clip head and the brake pedal:
Encase the U-shaped clamping pin in the hole of U-shaped clip
head and the brake pedal, and then mount the spring pin on the
U-shaped clamping pin.SST
washer
SST
(Diesel engine)

SR-11Steering System
Power Steering (General Introduction)
power steering oil pump
power steering gear steering drive shaft
oil cup
Power steering
Introduction
Principal of Power Steering
The power steering is a kind of hydraulic device that use
the engine power to steer. The engine drive the power
steering oil pump to generate the hydraulic pressure, which
actuates the piston in steering gear, so that the worm shaft
can provide to the piston with a supplementary force, which
has relation with the pressure actuated on the piston.
Therefore, pressure increase is required if larger steering
force is needed, and the pressure variation is accomplished
through the control valve.
Intermediate position (forward straightly)
The liquid from the power steering oil pump is sent to
the control valve, which, if locates at the intermediate, will
allow the liquid to pass and enter into the drain outlet, finally
return the pump. At this time, it is difficult to increase the
pressure; meanwhile, due to the equal pressures at the both
sides of the power piston, it cannot move toward either side.
Steering time
When the steering drive shaft move toward either side,
the control valve will move together with it, in case one oil
passage is shut off, meanwhile open the other larger, the
liquid flow variation will increase the pressure, as result, the
unequal pressure at both sides of piston will make the piston
move toward the side of smaller pressure, therefore, the
liquid is pressed in the pump through the control valve.
pump control valve
drain outlet
power cylinde
power piston
segmental gear shaft worm shaftsteering gear
Pump

SR-12Steering System
Power Steering (Introduction)
Suggestion on maintenance
The failure of power steering system usually relates to the
steering difficulty due to lack of supplementary force. In such
case, it is the first to verify the problem is produced by the pump
or steering gear when repairing. In doing so, the problem can be
checked on vehicle with the pressure meter.
On-vehicle Inspection
As the power steering is a hydraulic pressure device, its
trouble usually caused by the lack of specified hydraulic
pressure or the abnormal work of control valve. As a result, it
cannot acquire the moderate hydraulic pressure.
In case the problem is caused by the pump, the steering
wheel will deflect toward right or left. On the other side, if the
problem is caused by control valve, when the steering wheel
rotates to left or right, the steering will become more difficult
due to the unequal supplementary force. However, when there
is wear on the piston sealing ring of power cylinder, it also cause
the hydraulic pressure loss that may lead into steering difficulty
toward right or left.
Before making inspection on vehicle, verify the power
steering system firstly to see whether there is air. If any, the air
volume will increase with the variation of hydraulic pressure,
which will cause the hydraulic pressure fluctuation that makes
the power steering work abnormally. In order to verify whether
there is any air in the system, check whether the liquid level
varies or not when the steering wheel rotates completely toward
the right or left. For instance, if there is air in the system, the air
will be compressed, which will reduce the liquid level
remarkably, when the steering wheel rotating. If there is no air
in system, the liquid level variation is very small even though
the hydraulic pressure increases. This is because the liquid
volume will not varies when being compressed. And the small
liquid level variation is caused by the expansion of hose
between the pump and steering gear when the hydraulic pres-
sure increasing.
Meanwhile, the air in system sometimes will cause the
pump or steering gear produce noise when the steering wheel
rotating completely toward a certain direction. After checking
or exchanging the pump or steering gear, the on-vehicle inspec-
tion should be often conducted to guarantee the normal work of
power steering system.

SR-14Steering System
Power Steering (On-Vehicle Inspection)
Change of power steering liquid
1. Tear down the oil-returning hose from the oil cup to
drain the liquid into the container;
2. Run the engine in the idle status, and rotate the
steering wheel toward the max rotating angle for
several times in right or left direction while draining the
liquid, until the oil in steering liquid is drained up.
3. Turn off the engine.
4. Connect the oil-returning pipe and inject the new
power steering liquid in the liquid tank;
Hydraulic oil type: No.8 Liquid drive oil (Q/SH003.01.012-88)
5. Start the engine, and make it running in the idle status.
Rotate the steering wheel to the max rotating angle repeatedly
several times, meanwhile, supplement new power steering
liquid in the liquid tank until there is no foam or turbidities in
the liquid tank, and the oil indicating lamp reaches the marked
range when the engine is turned off.
6. Tighten the liquid tank cover
7. Exhaust the air in the power steering system;
Ai-r bleeding in power steering system
1. Check the liquid level height in the liquid tank
Check the liquid level and, if needed, supplement the liquid.
2. Start the engine in the idle status and rotate the
steering wheel repeatedly to the max rotating angle
several times.
3. Turn off the engine and connect the ethane pipe and
bleeding plug.
4. Start the engine and rotate the steering wheel
repeatedly to the max rotating angle several times.
5. Locate the steering wheel at the intermediate position.