brake light GREAT WALL SAILOR 2006 Service Manual

CL-3Clutch
Inspection and Adjustment of Clutch Pedal, Air Exhausting of Clutch
Air-exhausting of clutch
Remark: in case operation needs to be conducted for the clutch
system or if there is air in clutch, exhaust the air.
Notice : Do not stain the painted surface with brake liquid,
if any brake liquid is left, wash it away immediately.
1.
Fill the brake liquid into the oil cup of clutch master cylinder;
The oil cup of master cylinder shall often be checked and, if
necessary, added with brake liquid.
2.
Connect the ethene resin pipe to the air-exhausting valve.
Insert the other end of the pipe into the container, half of which
is filled with brake liquid.
3. Air-exhausting in clutch system
a) Move the clutch pedal up and down slowly for several times.
b) Loosen the air-exhausting valve when pressing the pedal
increasingly until there is brake liquid overflowing, then
tighten the air-exhausting valve.
c)
Repeat this operation until the bubble in brake liquid disappears.
Inspection on and adjustment
of clutch pedal
1. Check whether the pedal height is correct
Pedal height that begins from front wall board:
Dr SF
(165
5)mm
SL SK SY SJ
(190-200)mm
2. Adjust the pedal height where necessary
Loosen the locking nut and screw off the adjusting bolts until
the pedal height is correct. Then screw up the locking nut.
Pedal free stroke
3. Check whether the pedal free stroke is correct
Press the pedal lightly until the resistance generated by clutch
occurs.
pedal free stroke: (5-15)mm
4. Adjust the pedal free stroke where necessary;
a) Loosen the locking nut and rotate the push-rod until the
stroke is correct;
b) Screw up the locking nuts;
c) Check the pedal height after the adjustment of pedal free
stroke.
adjusting spot in
pedal height
pedal height
pedal free stroke

BR-5Braking System
Inspection and Adjustment
pedal push rodbraking lamp switch
pedal push-rod
free stroke of
pedal: (3-6) mm
Inspection and adjustment
Inspection on and adjustment of brake pedal
1. Check the pedal height as shown in the drawing to
whether it is correct,
The height from the pedal to the front floor:
Dr SF
160mm
SL SK SY SJ
(190-200)mm
2. Adjust the pedal height if necessary:
(a) Loosen the locking nuts of braking lamp switch;
(b) Loosen the braking lamp switch to the most degree.
(c) Loosen the locking nuts of drag rod;
(d) Adjust the pedal height through rotating the pedal drag
rod;
(e) Rotate the stop light switch reversibly until it contact
with the stop baffle of pedal.
(f) Screw up the two locking nuts.
(g) Check the braking lamp is lightened or not when tread
down the brake pedal.
(h) Check and adjust the pedal free stroke after adjusting the
pedal height
QKAdjust the free stroke of pedal if necessary:
(a) Loosen the locking nuts of the pedal drag rod and rotate
the pedal drag rod to adjust the pedal free stroke.
(b) Start the engine to confirm the free stroke.
(c) Check the pedal height after adjusting the pedal free
stroke. 3. Inspection on Pedal Free Stroke:
(a) Stop the engine working and tread down the brake pedal
several times until the vacuum booster is not in the stage
of vacuum.
(b) Tread down the pedal until the resistance occurs, and
measure the distance shown in the drawing.
Pedal free stroke
(3-6)mm
pedal height

BR-11Brake System
Vacuum Booster
Inspection on Vacuum booster parts
Operation for one-way valve inspection
(Gasoline engine)
(a) Tear down the one-way valve;
(b) Check the air to see whether it flows from the vacuum
booster side toward the engine side.
(c) Check the air, change the one-way valve if the air flows
from the side of engine toward the vacuum booster.
(d) Mount the one-way valve in the right place.
(a) Tear down the one-way valve from the vacuum pipe.
(b) Check the air to see whether it flows from the side of
vacuum room to the hose.
(c) Check the air, and change the one-way valve if the air
flows to the hose to the vacuum room.
air
engine side booster side
air airless
air
hose side vacuum side
airairless
Mount of Vacuum Booster
1. Adjust the length of vacuum booster pushrod:
(a) Mount the sealing washer on the master cylinder;
(b) Put SST on the sealing washer and descend the pin rod
until it contact lightly the piston with its top;
(c) Put top of SST downward ,and mount it on the vacuum
booster.
(d) Check the clearance between the vacuum booster pushrod
and the head of pin on SST.
(e) Adjust the length of vacuum booster pushrod until the
pushrod touches the pinhead.
2. Mount the vacuum booster, sealing washer and Ushaped
clip head.
(a) Mount the vacuum booster and sealing washer.
(b) Mount the U-shaped clip head.
(c) Mount and tighten the assembling nuts of vacuum booster.
3. Connect the U-shaped clip head and the brake pedal:
Encase the U-shaped clamping pin in the hole of U-shaped clip
head and the brake pedal, and then mount the spring pin on the
U-shaped clamping pin.SST
washer
SST
(Diesel engine)

BR-44Braking System
Load Sensing Proportion Valve
(b) Tear down the mounting bolts of valve bracket, and load
sensing proportion valve cluster.
Mount of Load Sensing Proportion Valve
1. Mount the load sensing proportion valve cluster on the
frame.
2. Connect the claming head II with the bracket:
(a) Mount the claming head on the load inductive spring;
(b) Adjust the spacing A.
Initial adjustment: 78 mm;
(c) Mount the claming head II on the claming head bracket
3. Connect the brake pipeline;
Connect the brake pipeline with SST.
Fastening torque

Dr SF
(18
2)N
m
SL SK SY SJ
(19
1)N
m
4. Adjust the rear shaft load
5. Adjust the valve:
(a) When drag downward the load inductive spring, the
valve piston shall move downward smoothly.
(b) When mount the valve body, the valve piston shall touch
the load inductive sensing spring lightly.
(c) Screw up the mounting nuts of valve body.
SST

BE-8Body Electric System
Protective Box Position and Content
Content of Protective Box
1 protective box I
fuse
1.Small lamp 10A
2.Rain brus 20A
3.Ceiling lamp 10A
4.(Cigarette lighter) 15A
5.Back -u 15A
6.Brake 10A
7.electric window 30A
8.Instrument 10A
fuel delivery/break electromagnetic valve10A(diesel

9.Central control lock 15A Dr
A
B
C



1
2
3
456
789
SL SK
U
N
O
V
P
Q
R NM
NN
NO
S
T NP
NQ
FUSE
1. Protection 10A
2. Unload
3. Charging 10A
4. Back-up 10A
5. ECU 10A
6. Unload
7. Rain wiper 10A
8. Stop lamp 10A
9. Ceiling lamp 10A
10. Central control lock 15A
11. Dual flasher 10A
12. EC 10A
13. Fuel pump 10A
14. Cigarette lighter 15Arelay
A electric window relay
B. small lamp relay
C.(flasher)

(plugging elements of ceiling
lamp wire harness)

(plugging elements of wire
harness in engine room)

BE-9Body Electric System
Protective Box Position and Content
fuse relay
1. Small lamp 10A A. electromagnetic fan relay
2. Brake 5A B. lasher
3. Ceiling lamp 5A C. electromagnetic fan relay
4. Central control lock 15A D. small lamp relay
5. Electric rocker gear 30A E. electric window relay
6. Dual flasher 10A
7. Cigarette lighter 15A
8. Rear vision mirror 5A (1) plugging elements of ceiling lamp wire harness
9. Unload (2) plugging elements of wire harness at front left door
10. Acoustic device 15A (3)plugging elements of wire harness in engine room
11. Rear window 20A
12. Electromagnetic fan 10A
13. Instrument 5A
14. Back-up lamp 5A
15. Rain brush 10A
16. Steering 5A
17. Unload
18. Unload




A
B
C
E D
123 456
78 9 101112
13 14 15
16 1718
SF
Protective bos I (continued)

BE-32Body Electric System
Combination Instrument
Combination instrument
Electric circuit diagram

  



^N ^NS _N _ N P
DraêaáÉëÉärear fog lamp indicating lamp
rear window/defroster indicating lamp
upper beam indicating lamp
front fog-lamp indicating lamp
A13
B3

connected
with
negative
pole
A10
connected
with
positive
pole
A2
connected
with
negative
polewater
thermometer
tachometer
speedometerconnected with sensor
connected with revolution signal
connected with sensor anode
connected with sensor
fuel gauge
connected with sensor
braking liquid level indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp
left turn indicating lamp
right turn indicating lamp
instrument interior
lighting lamp
liquid crystal back-light lamp
A1A16 B1 A5 A6A7 A8 A9 B6 B8 B9B10 B11A12 B4
A15
A14
A10
connected
with
positive
pole
A3
A4
B12
B13
B5
A13
B3

connected
with
negative
pole
A10
connected
with
positive
pole
A2
connected
with
negative
pole
liquid crystal back-light lampinstrument interior
lighting lamp
rear fog lamp indicating lamp
upper beam indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
speedometer
fuel gaugeconnection with sensor
connected with revolution signal
connected with sensor anode
connected with sensor
connected with sensor
oil-water separation indicating lamp
safety belt indicating lamp
parking brake indicating lamp
braking liquid level indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp
left turn indicating lamp
right turn indicating lamp
A1 A16 B1
A5 A6 A7A8
A9 B6 B8
B9 B10
B11 A4A12 A14 A15B4
A10
connected
with
positive
pole
A3
B12
B13
B5

BE-33Body Electric System
Combination Instrument
Electric circuit diagram (continued)
SF
A3 connected
with negative pole
A1 connected
with positive pole
B8 connected
with negative
pole
B7connected
with positive
pole
A4 connecting
with lighting
switch
A6 connected
with negative
pole
pressure-regulating
potential deviceirect-current
power supply
5-9Vdrive power
supply
110VEL
luminous
plate
left turn indicating lamp
right turn indicating lamp
upper beam indicating lamp
rear fog lamp indicating lamp
rear window/defroster indicating lamp
front fog-lamp indicating lamp
water
thermometer
tachometer
connected with sensor
connected with revolution signal
speedometer
digital clock
fuel gaugeconnect to the cathode of sensor
connected with sensor anode
connected with sensor
connected with sensor
back door indicating lamp
parking brake indicating lamp
safety airbag indicating lamp
low oil pressure indicating lamp
engine failure indicating lamp
four wheel drive indicating lamp
generator preheating indicating lamp
fuel alarming indicating lamp
accumulator charging indicating lamp
ABS failure indicating lamp75
B9
B2 A15 B1 A9 B11 B10
A14 B4 B6 A12
B14 connected
with positive
pole
B7 connected
with positive
pole
A11 A5A7 B12B5 B13 A16A13 B16 B15
A2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
In this drawing, A stands for the white plugging
elements, B for black plugging elements, they
use the same numerical order.
instrument
plugging element

BE-34Body Electric System
Combination Instrument
Electric circuit diagram (continued)
A16 A1 B16 B1
SL SK
B1
B16
A1
A16
speed and mileage meter
4P
G
VA9vehicle speed signal
A11odometer sensorA10odometer sensor anode
B11sensor signalelectronic tachometer
water thermometer
fuel gaugecoolant temperature sensor
B5
A12
fuel gauge sensor
B14
A2
B3
upper beam
_NPdifferential latch-in
safety belt
preheating
sediment water alarmingelectricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 Aturn indicating lamp
B16 left turn indicating lamp
A8
B4 +B7 - B8 A16 B15 B2B1 A15 A14B6 A13 B10B9
SY SJaccumulator plus four door-closing indicating lampA3turn on when the door is opened.
A11odometer sensor_NO
electronic odometer
electronic tachometerA10
B11
engine ignition coil
water thermometer
fuel gauge
B5
A12
neutral gear indicating lampA9
_NP
upper beamB14
differential latch-in
vacuum alarming
preheating
sediment water alarming
electricity charging/
discharging
fuel level alarming
brake failure alarming lamp
oil pressure alarming lamp
rear fog lamp
engine failure
four wheel drive indicating lamp
A1 left turn indicating lamp
B16 right turn indicating lamp
A8
B4 +
instrument lighting
system
B8
B7 - A16 B15 B2
B1 A15A14 B6 A13 B9 B3 B10A2
instrument lighting
system

BE-70
SF
1
2 P
4 5 6
7
8 9 10
11 12 13
14
15 16 1718 19
20
21
22
23
2425262728
29
30 3132
33
34
3536
37
38
39
40
41
42
43
44 45 46 47
48
49 50 51
52
53
54
555657 5859
Housing wire harness (continued)
60 61
1 left door lamp switch
2 defrost switch at tail door
3 window regulator at tail door
4 parking brake switch
5 ignition lock
6 combined switch
7 instrument
8 combined switch shell
9 grounding wire
10 amplifying plate of air-conditioner
11 heat-sensitive resistance
12 control panel of air-conditioner
13 A/C Switch
14 glove-box lamp switch
15 glove-box lamp
16 speed-adjusting resistance
17 blower
18 indoor temperature sensor
19 right front loudspeaker
20 brush motor
21 turn lamp on right side22 electric fan relay
23 maxi-fuse
24 joint of wire harness at right front door
25 right front door lamp switch
26 right electric back-up mirror
27 grounding wire
28 rear sound box wire
29 ashtray lamp
30 CD Device wire
31 cigarette lighter A
32 cigarette lighter B
33 dual flasher switch
34 fog lamp switch
35 temperature indicator
36 stop lamp switch
37 brake liquid level sensor
38 control case of central control lock
39 left front loudspeaker
40 automatic aerial
41 turn lamp on left side
42 generator43 left front conner lamp
44 left front lever-shaped lamp
45 front fog lamp
46 left headlamp
47 temperature control switch
48 connected to wire of 220
49 spraying motor A
50 spraying motor B
51 right front conner lamp
52 right headlamp
53 horn A
54 horn B
55 right front lever-shaped lamp
56 right front fog lamp
57 electric fan
58 outdoor temperature sensor
59 connected to chassis wire harness
anright central wire harness
60 connected to left central wire harness
61 connected to engine wire harness
Body Electric System
Wire Harness Distribution